FaultCodes.org

Fuel Trim & Air/O2 Metering Fault Codes (Auto & OBD-II)

72 diagnostic trouble codes covering Fuel Trim & Air/O2 Metering (Automotive & OBD-II) with symptom triage and fix steps.

72 codes indexed
Quick Answer

Our Fuel Trim & Air/O2 Metering index covers 72 fault codes in Automotive & OBD-II, led by high-frequency lookups like P0171, P0174, P0135, P0101. Of these, 18 carry high or critical urgency ratings requiring prompt inspection.

Auto & OBD-II
72 codes indexed
Urgency
18 high / critical
Popular Fault Codes
P0171
P0171OBD-II

System Too Lean (Bank 1)

Long-Term Fuel Trim on Bank 1 hit its upper enrichment limit (+25% to +36%) because excess unmeasured air entered combustion or fuel delivery fell short—commonly caused by split PCV/vacuum hoses, dirty MAF sensors, or weak fuel pumps.

P0174OBD-II

OBD-II P0174: System Too Lean (Bank 2)

SAE J2012 code set when Long Term Fuel Trim exceeds roughly `+20% to +25%` trying to keep Bank 2 (opposite cylinder #1) at `14.7:1`—compare freeze-frame idle vs 2,500 RPM trims and whether P0171 co-occurs.

P0135OBD-II

OBD-II P0135: O2 Sensor Heater Circuit (Bank 1, Sensor 1)

SAE J2012 heater circuit fault on upstream **Bank 1 Sensor 1** oxygen sensor—measure heater pins (`2–15 Ω` normal; `> 100 Ω / OL` open, `< 0.5 Ω` short) and confirm **12 V fuse feed + PCM PWM ground** during the `2–5 s` cold-start check.

P0101OBD-II

OBD-II P0101: Mass Air Flow (MAF) Sensor Range/Performance

Measured **MAF `g/s`** airflow deviates **`> 20% to 35%`** from the PCM's `RPM/MAP/TPS` airflow model for `2–4 s` steady-state—check **split intake boots, dirty hot-wire elements** (clean only with MAF-safe spray), **clogged air filters, or sticking PCV valves**.

P0141OBD-II

OBD-II P0141: O2 Sensor Heater Circuit (Bank 1, Sensor 2)

Downstream post-cat **Bank 1 Sensor 2** heater circuit fault—measure heater pins (**`2–15 Ω` normal**, **`> 100 Ω / OL` open**, **`< 0.5 Ω` short**) and inspect the **dedicated heater fuse, road-salt corroded underbody pins**, and **`12 V` feed + PCM PWM ground**.

P0102OBD-II

OBD-II P0102: Mass or Volume Air Flow (MAF) Sensor "A" Circuit Low Input

SAE J2012 powertrain fault when the **MAF signal drops below the hardware floor (`< 0.15–0.20 V` or near `0.0 g/s`)**—usually caused by an **unplugged connector, blown MAF fuse, open wire/short to ground, or oil-fouled hot-wire element**.

P0172OBD-II

OBD-II P0172: System Too Rich (Bank 1)

SAE J2012 fuel-trim fault triggered when Bank 1 adaptive **Long-Term Fuel Trim (`LTFT`) drops below `-20% to -25%`**—caused by a **stuck-open EVAP purge valve (`P0496`), leaking fuel injector, oil-fouled MAF over-reporting air, high fuel pressure, or skewed cold ECT sensor**.

P0175OBD-II

OBD-II P0175: System Too Rich (Bank 2)

SAE J2012 code set when Bank 2 adaptive Long Term Fuel Trim drops below `-20% to -25%` trying to lean out an over-fueled cylinder bank—check whether `P0172` co-occurs to isolate global MAF/fuel-pressure/EVAP purge faults vs Bank 2 injectors or O2 bias.

P0138OBD-II

OBD-II P0138: O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)

Downstream post-catalyst zirconia O2 sensor (`B1S2`) stays pinned `> 0.80–0.90 V` continuously—inspect for melted signal wire shorted to `12 V` heater power, chronically rich running (`P0172`), or an internally shorted sensor before swapping parts.

P0133OBD-II

OBD-II P0133: O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)

Upstream Bank 1 Sensor 1 (`B1S1`) cross-count transition across `450 mV` exceeds `~100–300 ms`—graph live `0.1–0.9 V` waveform oscillation and rule out pre-cat exhaust leaks, fuel-trim bias, or silicone/coolant poisoning before replacing `B1S1`.

P0131OBD-II

OBD-II P0131: O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)

Upstream `B1S1` O2 signal stayed pinned `< 150–200 mV` for `> 2–5 s` in closed loop—use a brief intake fuel-enrichment pulse (`> 0.8 V` jump proves the sensor works!) to separate severe vacuum/fuel starvation from a shorted ground wire or dead sensor.

P2195OBD-II

OBD-II P2195: O2 Sensor Signal Biased / Stuck Lean (Bank 1 Sensor 1)

Wideband A/F pump current (`Ip`) or Nernst cell signal on `B1S1` remains stuck lean (`λ > 1.05–1.10`) despite maxed positive `STFT` enrichment—run a brief fuel-enrichment test to separate massive vacuum/exhaust leaks or low fuel pressure from a dead wideband A/F sensor or open signal wire.

P0100OBD-II

Mass or Volume Air Flow Sensor A Circuit

OBD-II P0100: Mass or Volume Air Flow Sensor A Circuit

P0103OBD-II

Mass or Volume Air Flow Sensor A Circuit High

OBD-II P0103: Mass or Volume Air Flow Sensor A Circuit High

P0104OBD-II

Mass or Volume Air Flow Sensor A Circuit Intermittent

OBD-II P0104: Mass or Volume Air Flow Sensor A Circuit Intermittent

P0105OBD-II

Manifold Absolute Pressure/Barometric Pressure Sensor Circuit

OBD-II P0105: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit

P0106OBD-II

Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance

OBD-II P0106: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance

P0107OBD-II

Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Low

OBD-II P0107: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Low

P0108OBD-II

Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High

OBD-II P0108: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High

P0109OBD-II

Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Intermittent

OBD-II P0109: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Intermittent

P010AOBD-II

Mass or Volume Air Flow Sensor B Circuit

OBD-II P010A: Mass or Volume Air Flow Sensor B Circuit

P010BOBD-II

Mass or Volume Air Flow Sensor B Circuit Range/Performance

OBD-II P010B: Mass or Volume Air Flow Sensor B Circuit Range/Performance

P010COBD-II

Mass or Volume Air Flow Sensor B Circuit Low

OBD-II P010C: Mass or Volume Air Flow Sensor B Circuit Low

P010DOBD-II

Mass or Volume Air Flow Sensor B Circuit High

OBD-II P010D: Mass or Volume Air Flow Sensor B Circuit High

P010EOBD-II

Mass or Volume Air Flow Sensor B Circuit Intermittent/Erratic

OBD-II P010E: Mass or Volume Air Flow Sensor B Circuit Intermittent/Erratic

P010FOBD-II

Mass or Volume Air Flow Sensor A/B Correlation

OBD-II P010F: Mass or Volume Air Flow Sensor A/B Correlation

P0130OBD-II

O2 Sensor Circuit Bank 1 Sensor 1

OBD-II P0130: O2 Sensor Circuit Bank 1 Sensor 1

P0132OBD-II

O2 Sensor Circuit High Voltage Bank 1 Sensor 1

OBD-II P0132: O2 Sensor Circuit High Voltage Bank 1 Sensor 1

P0134OBD-II

O2 Sensor Circuit No Activity Detected Bank 1 Sensor 1

OBD-II P0134: O2 Sensor Circuit No Activity Detected Bank 1 Sensor 1

P0136OBD-II

O2 Sensor Circuit Bank 1 Sensor 2

OBD-II P0136: O2 Sensor Circuit Bank 1 Sensor 2

P0137OBD-II

O2 Sensor Circuit Low Voltage Bank 1 Sensor 2

OBD-II P0137: O2 Sensor Circuit Low Voltage Bank 1 Sensor 2

P0139OBD-II

O2 Sensor Circuit Slow Response Bank 1 Sensor 2

OBD-II P0139: O2 Sensor Circuit Slow Response Bank 1 Sensor 2

P013AOBD-II

O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2

OBD-II P013A: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2

P013BOBD-II

O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 2

OBD-II P013B: O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 2

P013COBD-II

O2 Sensor Slow Response - Rich to Lean Bank 2 Sensor 2

OBD-II P013C: O2 Sensor Slow Response - Rich to Lean Bank 2 Sensor 2

P013DOBD-II

O2 Sensor Slow Response - Lean to Rich Bank 2 Sensor 2

OBD-II P013D: O2 Sensor Slow Response - Lean to Rich Bank 2 Sensor 2

P013EOBD-II

O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 2

OBD-II P013E: O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 2

P013FOBD-II

O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 2

OBD-II P013F: O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 2

P0140OBD-II

O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2

OBD-II P0140: O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2

P0142OBD-II

O2 Sensor Circuit Bank 1 Sensor 3

OBD-II P0142: O2 Sensor Circuit Bank 1 Sensor 3

P0143OBD-II

O2 Sensor Circuit Low Voltage Bank 1 Sensor 3

OBD-II P0143: O2 Sensor Circuit Low Voltage Bank 1 Sensor 3

P0144OBD-II

O2 Sensor Circuit High Voltage Bank 1 Sensor 3

OBD-II P0144: O2 Sensor Circuit High Voltage Bank 1 Sensor 3

P0145OBD-II

O2 Sensor Circuit Slow Response Bank 1 Sensor 3

OBD-II P0145: O2 Sensor Circuit Slow Response Bank 1 Sensor 3

P0146OBD-II

O2 Sensor Circuit No Activity Detected Bank 1 Sensor 3

OBD-II P0146: O2 Sensor Circuit No Activity Detected Bank 1 Sensor 3

P0147OBD-II

O2 Sensor Heater Circuit Bank 1 Sensor 3

OBD-II P0147: O2 Sensor Heater Circuit Bank 1 Sensor 3

P0148OBD-II

Fuel Delivery Error

OBD-II P0148: Fuel Delivery Error

P0149OBD-II

Fuel Timing Error

OBD-II P0149: Fuel Timing Error

P014AOBD-II

O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 2

OBD-II P014A: O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 2

Frequently Asked Questions

What causes Fuel Trim & Air/O2 Metering fault codes?

Codes under Fuel Trim & Air/O2 Metering (Automotive & OBD-II) indicate out-of-range sensor signals, circuit faults, mechanical wear, or leaks within that subsystem. Notable examples include P0171, P0174, P0135, P0101.

Are Fuel Trim & Air/O2 Metering fault codes safe to ignore?

18 of the 72 indexed Fuel Trim & Air/O2 Metering codes are flagged high or critical urgency. Even low-severity alerts can trigger failed inspections or secondary damage if left unresolved.

How much does it cost to repair a Fuel Trim & Air/O2 Metering fault?

Repair costs range from $0–$50 for DIY connector, fuse, or hose fixes to professional service rates depending on the affected module. Open any specific code page below to compare DIY parts vs. professional labor estimates.

Fuel Trim & Air/O2 Metering Fault Codes (Auto & OBD-II) — Causes, Fixes & Cost | FaultCodes.org