FaultCodes.org

Automotive & OBD-II

Diagnostic trouble codes (P, B, C, U) for Ford, Toyota, BMW, VW, GM, and generic SAE J2012 vehicles with repair cost ranges.

18,923 codes indexed
P0420OBD-II

Catalyst System Efficiency Below Threshold (Bank 1)

The Bank 1 catalytic converter fell below oxygen-storage or thermal efficiency thresholds compared with upstream sensor readings—caused by catalyst aging, oil/misfire poisoning, exhaust leaks ahead of Sensor 2, or skewed O2 sensors.

P0300OBD-II

Random / Multiple Cylinder Misfire Detected

Crankshaft speed monitoring detected engine misfires across multiple cylinders (or changing randomly)—triggering a solid Check Engine light at ~1–2%+ emissions rate and a FLASHING warning light at >= 5% catalyst-damaging misfire rate.

P0171OBD-II

System Too Lean (Bank 1)

Long-Term Fuel Trim on Bank 1 hit its upper enrichment limit (+25% to +36%) because excess unmeasured air entered combustion or fuel delivery fell short—commonly caused by split PCV/vacuum hoses, dirty MAF sensors, or weak fuel pumps.

P0128OBD-II

Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

Engine coolant took too long to reach regulating temperature after a cold start—such as falling below ~65 °C on GM heat models or <78 °C on Ford 89 °C thermostats—overwhelmingly caused by a stuck-open thermostat.

P0442OBD-II

Evaporative Emission (EVAP) System Small Leak Detected (0.040" / 1 mm)

Fuel vapor containment failed a ~0.040 in (1 mm) / 0.020 in pressure-decay leak test—most commonly caused by a loose or cracked rubber gas cap gasket, split EVAP purge hose, or leaking canister vent seal.

P0455OBD-II

Evaporative Emission (EVAP) System Large Leak Detected

Zero tank vacuum built up during the EVAP pull-down test—such as failing to reach ~-2 kPa in 30 s (Ford) or 2,740 Pa after 20 L purge (GM)—usually caused by a missing/loose gas cap, popped EVAP hose, stuck-open vent valve, or stuck-closed purge solenoid.

P0301OBD-II

Cylinder 1 Misfire Detected

Over 90% of detected crankshaft-speed misfires are occurring specifically on Cylinder 1—commonly solved cleanly via a 5-minute coil/spark plug swap test to isolate a bad Cylinder 1 ignition coil, cracked plug insulator, or clogged injector.

P0174OBD-II

OBD-II P0174: System Too Lean (Bank 2)

SAE J2012 code set when Long Term Fuel Trim exceeds roughly `+20% to +25%` trying to keep Bank 2 (opposite cylinder #1) at `14.7:1`—compare freeze-frame idle vs 2,500 RPM trims and whether P0171 co-occurs.

P0401OBD-II

OBD-II P0401: Exhaust Gas Recirculation (EGR) Flow Insufficient Detected

SAE J2012 emissions code set when EGR valve commands fail to produce expected **DPFE pressure, MAP/MAF change, or EGR temperature rise**—often caused by **carbon-clogged intake ports or failing DPFE sensors** rather than the valve itself.

P0135OBD-II

OBD-II P0135: O2 Sensor Heater Circuit (Bank 1, Sensor 1)

SAE J2012 heater circuit fault on upstream **Bank 1 Sensor 1** oxygen sensor—measure heater pins (`2–15 Ω` normal; `> 100 Ω / OL` open, `< 0.5 Ω` short) and confirm **12 V fuse feed + PCM PWM ground** during the `2–5 s` cold-start check.

P0430OBD-II

OBD-II P0430: Catalyst System Efficiency Below Threshold (Bank 2)

Bank 2 catalytic converter **oxygen storage capacity (OSC)** monitor failed because downstream **B2S2** O2 voltage swings like upstream **B2S1** instead of holding steady `~0.6–0.7 V`—rule out **exhaust leaks, misfires, and fuel trims** before replacing the Bank 2 cat.

P0101OBD-II

OBD-II P0101: Mass Air Flow (MAF) Sensor Range/Performance

Measured **MAF `g/s`** airflow deviates **`> 20% to 35%`** from the PCM's `RPM/MAP/TPS` airflow model for `2–4 s` steady-state—check **split intake boots, dirty hot-wire elements** (clean only with MAF-safe spray), **clogged air filters, or sticking PCV valves**.

P0302OBD-II

OBD-II P0302: Cylinder 2 Misfire Detected

Mode `$06` **Cylinder 2** misfire counter exceeded threshold—use fast **coil-swap + plug-swap isolation** (`#2 -> #1/#3` to see if code moves to `P0301/P0303`), check **spark gap, injector pulse & compression (`~120–180 psi`, within `10–15%`)**; **STOP immediately if the CEL flashes** (catalyst meltdown hazard).

P0303OBD-II

OBD-II P0303: Cylinder 3 Misfire Detected

Mode `$06` **Cylinder 3** misfire monitor triggered—swap **Coil #3 -> #1/#2** and **Plug #3 -> a separate cylinder** to pinpoint coil vs plug vs injector/compression; check **oil inside the #3 spark plug well** (valve cover gasket) and **stop immediately if the CEL flashes**.

P0304OBD-II

OBD-II P0304: Cylinder 4 Misfire Detected

Mode `$06` **Cylinder 4** misfire counter exceeded limit—swap **Coil #4 -> #1/#2**, inspect plug wear/carbon tracking, test **injector resistance (`~11–16 Ω` port injection) + noid light**, and check **compression/leakdown** if #4 stays dead; **STOP if the CEL flashes**.

P0440OBD-II

OBD-II P0440: Evaporative Emission (EVAP) Control System Malfunction

General EVAP self-test fail across purge, vent, or tank sealing—check **gas cap O-ring** first, then ohm-test **purge (`18–30 Ω`) & vent (`20–40 Ω`) solenoids**, verify **FTP sensor baseline (`~2.5–3.0 V` KOEO cap off)**, and pinpoint leaks with a **low-pressure EVAP smoke test**.

P0456OBD-II

OBD-II P0456: EVAP System Very Small Leak Detected (0.020 in)

CARB/EPA **`0.020-inch (0.5 mm)` micro-leak** threshold tripped (half the `0.040 in` P0442 pinhole)—inspect the **gas cap gasket & rusted filler neck lip**, check **purge valve weep**, and pinpoint with a **low-pressure EVAP smoke tester (`~0.5–1.0 psi`)**.

P0118OBD-II

OBD-II P0118: Engine Coolant Temperature (ECT) Circuit High Input

NTC thermistor signal pulled **`≥ 4.6 V`** (open circuit / infinite resistance), defaulting PCM coolant temp to **`-40 °C (-40 °F)`**—causes **hard cold starts, over-rich fueling & cooling fans locked ON**; inspect unplugged/corroded pins and test the **ohm curve (`~2–3 kΩ @ 20 °C` -> `~200–300 Ω @ 90 °C`)**.

P0340OBD-II

OBD-II P0340: Camshaft Position Sensor "A" Circuit (Bank 1)

Missing or erratic **Bank 1 Intake Camshaft Position (CMP)** signal (3-wire `5V/12V` Hall-effect square wave or 2-wire VR AC pulse), causing **extended cranking, stalling, or no-start**—test **`5 V / 12 V` reference + ground + signal continuity**, clean **metallic debris off sensor tip**, and inspect **timing belt/chain slack**.

P0507OBD-II

OBD-II P0507: Idle Air Control (IAC) System RPM Higher Than Expected

Actual warm idle exceeds target map by **`> 100–200 RPM`** continuously (`5–10 s`) while throttle is closed—check **unmetered intake vacuum leaks**, **carbon-bound Electronic Throttle Body (ETB) / IACV**, and run the **OEM Idle Air Volume Relearn** after cleaning.

P0700OBD-II

OBD-II P0700: Transmission Control System (MIL Request)

Informational **ECM flag** proving the **Transmission Control Module (TCM)** stored active fault(s)—generic OBD-II scanners **only show `P0700`**; use an **enhanced/OEM all-module scanner** to pull the true TCM root code (`P0715`, `P0730`, `P0741`, solenoid codes) and check **ATF level/condition + battery voltage** first.

P0011OBD-II

OBD-II P0011: "A" Camshaft Position Timing Over-Advanced (Bank 1)

Bank 1 intake camshaft phaser stays **over-advanced** vs crankshaft target—**check engine oil level & sludge condition FIRST**, then ohm-test **VVT Oil Control Valve (OCV) solenoid (`6.0–12.0 Ω @ 20 °C`, `OL` to ground, 12V bench click)**, clean **clogged VVT oil screens**, and check for a **stretched timing chain**.

P0141OBD-II

OBD-II P0141: O2 Sensor Heater Circuit (Bank 1, Sensor 2)

Downstream post-cat **Bank 1 Sensor 2** heater circuit fault—measure heater pins (**`2–15 Ω` normal**, **`> 100 Ω / OL` open**, **`< 0.5 Ω` short**) and inspect the **dedicated heater fuse, road-salt corroded underbody pins**, and **`12 V` feed + PCM PWM ground**.

P0325OBD-II

OBD-II P0325: Knock Sensor 1 Circuit (Bank 1)

Piezoelectric **Bank 1 Knock Sensor (`KS1`)** circuit open/shorted or producing zero detonation voltage—PCM **retards ignition timing** conservatively (causing **sluggish acceleration & lower MPG**); check **rodent-chewed under-manifold knock harness**, verify **exact mounting bolt torque**, and test **resistance / AC mV tap response**.

P0446OBD-II

OBD-II P0446: EVAP Emission Control System Vent Control Circuit

SAE J2012 emissions fault when the **canister vent solenoid** sticks closed/open, its **20–40 Ω** (up to **50–70 Ω**) coil circuit faults, or the charcoal canister fresh-air filter plugs—often causing **slow gas-pump click-offs** during refueling.

P0102OBD-II

OBD-II P0102: Mass or Volume Air Flow (MAF) Sensor "A" Circuit Low Input

SAE J2012 powertrain fault when the **MAF signal drops below the hardware floor (`< 0.15–0.20 V` or near `0.0 g/s`)**—usually caused by an **unplugged connector, blown MAF fuse, open wire/short to ground, or oil-fouled hot-wire element**.

P0113OBD-II

OBD-II P0113: Intake Air Temperature (IAT) Sensor 1 Circuit High

SAE J2012 fault when an **open NTC circuit pulls the IAT line `> 4.6–4.85 V`**, locking PCM air-temp readings at **`< -40 °C (-40 °F)`**—extremely common right after an air filter change leaves an **integrated MAF/IAT plug unplugged**.

P0172OBD-II

OBD-II P0172: System Too Rich (Bank 1)

SAE J2012 fuel-trim fault triggered when Bank 1 adaptive **Long-Term Fuel Trim (`LTFT`) drops below `-20% to -25%`**—caused by a **stuck-open EVAP purge valve (`P0496`), leaking fuel injector, oil-fouled MAF over-reporting air, high fuel pressure, or skewed cold ECT sensor**.

P0335OBD-II

OBD-II P0335: Crankshaft Position (CKP) Sensor "A" Circuit

Critical SAE J2012 powertrain fault—loss of primary **CKP RPM/TDC signal** leaves the engine **cranking with `0 RPM` on tachometer/scanner and NO spark or fuel injector pulse**; check **`5 V / 12 V` Hall supply** or **VR coil (`~300–1,500 Ω`)**, **oil-soaked crank-pulley wiring**, and **damaged reluctor teeth**.

P0411OBD-II

OBD-II P0411: Secondary Air Injection (SAIR) System Incorrect Flow Detected

SAE J2012 cold-start emissions code triggered when the **SAIR pump fails to produce an expected lean O2 shift within `2–5 s` of activation** (or sufficient secondary air pressure)—check **SAIR fuse/relay, water-logged electric pump, rusted combi check valves, and cracked vacuum lines**.

P2096OBD-II

OBD-II P2096: Post Catalyst Fuel Trim System Too Lean (Bank 1)

SAE J2012 trim-bias fault when the **downstream post-cat O2 sensor stays biased lean (`< 0.45 V` / `λ > 1.02`) over steady cruise integration**—most commonly caused by a **small exhaust leak between upstream and downstream O2 sensors** (flex pipe/flange), a **skewed rear O2 sensor**, **fuel-starved Bank 1**, or **degraded catalyst oxygen storage**.

P0016OBD-II

OBD-II P0016: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A)

Critical SAE J2012 mechanical phase-timing fault between the **crankshaft and Bank 1 intake camshaft (`Sensor A`)**—**STOP driving interference engines aggressively** to prevent piston-to-valve collision; verify **oil level/sludge & VVT OCV (`6–12 Ω`)** first, then check for a **stretched timing chain, jumped timing belt, failed tensioner, or slipped reluctor via dual-channel oscilloscope**.

P0193OBD-II

OBD-II P0193: Fuel Rail Pressure (FRP) Sensor "A" Circuit High Input

SAE J2012 high-pressure fuel fault when a **returnless port or GDI rail sensor clips `> 4.8–4.95 V` (against the `5.0 V` reference)**, triggering limp-home mode—inspect for **open sensor ground, signal short to `5 V`, unplugged rail sensor**, and compare **mechanical vs scan-tool rail pressure (`~35–65 psi` port / `500–2,500+ psi` GDI)**.

P0496OBD-II

OBD-II P0496: EVAP System High Purge Flow (Flow During Non-Purge)

SAE J2012 EVAP fault when the **canister purge solenoid sticks physically open**, drawing **continuous intake vacuum into the fuel tank even when commanded `0%` closed**—famous for causing **hard starts right after filling the gas tank**; verify via idle hose suction test and coil check (`18–30 Ω`).

P0715OBD-II

OBD-II P0715: Input/Turbine Shaft Speed Sensor "A" Circuit

SAE J2012 transmission fault when the **TCM loses the input/turbine shaft RPM signal**, triggering **harsh/delayed shifts or 2nd/3rd gear limp mode**—inspect **ATF level/metal shavings**, **connector oil wicking**, and measure **VR coil resistance (`~300–1,200 Ω`)** or **Hall-effect `5 V / 12 V` reference**.

U0100OBD-II

OBD-II U0100: Lost Communication With ECM/PCM "A" (CAN Bus Timeout)

Critical SAE J2012 network fault—CAN-H / CAN-L bus nodes lost the **ECM/PCM heartbeat**; check **battery voltage (`≥ 12.6 V` KOEO) and ECM main fuses/relays FIRST**, then (with **battery disconnected**) measure **OBD-II Pin 6 (CAN-H) to Pin 14 (CAN-L) = `60 Ω` normal** (`120 Ω` open leg, `0 Ω` shorted bus).

C0035OBD-II

OBD-II C0035: Left Front Wheel Speed Sensor Circuit (ABS / ESC Fault)

SAE J2012 chassis fault—**ABS, ESC & Traction Control lights illuminate** and ABS disables while base hydraulic brakes still work cautiously; inspect **front-left wheel-well harness flex cracks, rust-jacked air gap / cracked tone ring, loose wheel bearing play**, and check **2-wire passive ohms (`~800–2,000 Ω`) or active live wheel speed parity (`0 km/h` mismatch)**.

B0001OBD-II

OBD-II B0001: Driver Frontal Stage 1 Deployment Control Circuit (SRS Airbag)

Critical SAE J2012 SRS restraint fault—**Airbag warning light stays ON and the driver frontal airbag is DISABLED in a crash**; **CRITICAL SAFETY RULE: NEVER probe SRS squib/inflator pins with a standard ohmmeter** (meter test current can fire the airbag!). Certified techs disconnect 12V negative for **≥ 10–15 min** and use an approved **`~2.0–2.5 Ω` SRS simulator** to isolate the **clock spring** (often with dead horn/steering buttons), **yellow SRS connectors**, or **SRS module**.

P0299OBD-II

Turbocharger / Supercharger "A" Underboost Condition

Actual boost pressure lagged significantly behind target boost—such as >4 psi (28 kPa) for 5 seconds on Ford EcoBoost or 30–55 kPa below target on GM petrol engines—most commonly caused by boost hose leaks, worn wastegate rods, diverter diaphragms, or winter intercooler icing.

P0441OBD-II

OBD-II P0441: Evaporative Emission (EVAP) System Incorrect Purge Flow

SAE J2012 EVAP code triggered when the PCM sees **purge flow while commanded closed OR zero vacuum/pressure drop when commanded open**—inspect **split purge vacuum lines**, test **purge solenoid (`18–30 Ω`) & idle suction**, check **canister vent valve (`20–40 Ω`)**, and verify **FTP atmospheric voltage (`~2.5–3.0 V` cap off)**.

P0175OBD-II

OBD-II P0175: System Too Rich (Bank 2)

SAE J2012 code set when Bank 2 adaptive Long Term Fuel Trim drops below `-20% to -25%` trying to lean out an over-fueled cylinder bank—check whether `P0172` co-occurs to isolate global MAF/fuel-pressure/EVAP purge faults vs Bank 2 injectors or O2 bias.

P0014OBD-II

OBD-II P0014: "B" Camshaft Position Timing Over-Advanced or System Performance (Bank 1)

Exhaust (`"B"`) camshaft phaser on Bank 1 stayed over-advanced or lagged behind ECM target—check engine oil level, viscosity, and sludge FIRST, ohm-test the exhaust VVT OCV solenoid (`6.0–12.0 Ω` @ `20 °C`), and inspect clogged oil screens or cam phaser lock pins.

P0138OBD-II

OBD-II P0138: O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)

Downstream post-catalyst zirconia O2 sensor (`B1S2`) stays pinned `> 0.80–0.90 V` continuously—inspect for melted signal wire shorted to `12 V` heater power, chronically rich running (`P0172`), or an internally shorted sensor before swapping parts.

P0133OBD-II

OBD-II P0133: O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)

Upstream Bank 1 Sensor 1 (`B1S1`) cross-count transition across `450 mV` exceeds `~100–300 ms`—graph live `0.1–0.9 V` waveform oscillation and rule out pre-cat exhaust leaks, fuel-trim bias, or silicone/coolant poisoning before replacing `B1S1`.

P0131OBD-II

OBD-II P0131: O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)

Upstream `B1S1` O2 signal stayed pinned `< 150–200 mV` for `> 2–5 s` in closed loop—use a brief intake fuel-enrichment pulse (`> 0.8 V` jump proves the sensor works!) to separate severe vacuum/fuel starvation from a shorted ground wire or dead sensor.

P0449OBD-II

OBD-II P0449: EVAP System Vent Valve / Solenoid Control Circuit

Pure electrical open or short circuit in the rear charcoal canister vent valve solenoid—frequently triggered by road-salt pigtail corrosion; check the EVAP fuse, verify `20–40 Ω` solenoid coil resistance, and test `12 V` ignition feed plus ECM ground control.

P0451OBD-II

OBD-II P0451: EVAP System Pressure Sensor / Switch Range / Performance

Fuel Tank Pressure (`FTP`) sensor reads erratically, drifts, or stays stuck off atmospheric baseline—verify KOEO open-cap baseline (`~2.5–3.0 V` by OEM), `5.0 V` reference/ground, plugged canister vent, or corroded top-of-tank FTP plug.

P0562OBD-II

OBD-II P0562: System Voltage Low (Battery / Alternator Charging Fault)

ECM battery/ignition supply dropped below `~10.0–11.0 V`—measure KOEO resting voltage (`~12.6 V`) and running load voltage (`13.5–14.5 V` @ idle & `2,000 RPM`); ALWAYS fix `P0562` FIRST because sagging voltage triggers false `U0100`, `P2135`, and `P0016` codes.

Automotive & OBD-II — FaultCodes.org | FaultCodes.org