FaultCodes.org
P0016OBD-IIPowertrain & Engine ManagementVerified Guide· Updated: Nov 22, 2026

OBD-II P0016: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A)

Critical SAE J2012 mechanical phase-timing fault between the crankshaft and Bank 1 intake camshaft (`Sensor A`)—STOP driving interference engines aggressively to prevent piston-to-valve collision; verify oil level/sludge & VVT OCV (`6–12 Ω`) first, then check for a stretched timing chain, jumped timing belt, failed tensioner, or slipped reluctor via dual-channel oscilloscope.

Quick AnswerCritical — Stop Immediately

Code P0016 (SAE J2012) means the crankshaft and Bank 1 intake camshaft (`Sensor A`) are mechanically out of phase correlation. CRITICAL SAFETY WARNING: Most modern engines are interference designs—stop driving aggressively and avoid high RPM (have the vehicle inspected promptly or towed if chain rattle/rough running is present) because jumping one more tooth can bend valves and destroy the engine! Always check engine oil level, sludge, and the VVT Oil Control Valve (OCV) solenoid (`6–12 Ω` coil) first, then inspect for a stretched timing chain, jumped timing belt teeth, collapsed hydraulic tensioner, or slipped reluctor wheel using a dual-channel oscilloscope ($40–$220 DIY sensor/OCV checks; $650–$2,400 professional timing chain/belt overhaul).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Powertrain & Engine Management
Professional Repair
$650 – $2,400

What This Fault Code Means

The PCM continuously compares the phase angle between the Crankshaft Position (CKP) trigger wheel and Bank 1 Intake Camshaft Position (CMP "A") signal against stored base timing (0° parked phase). Even a one-tooth timing chain stretch/jump, a sticky oil-sludged VVT phaser/OCV, or a spun camshaft reluctor tone wheel shifts cam-to-crank alignment past the OEM tolerance threshold and triggers P0016.

Common Symptoms

  • Metallic timing chain rattle on cold startup, rough idle, stalling, or severe power loss
  • Extended cranking before startup and illuminated Check Engine Light (P0016, often paired with P0011 or P0017)
  • Audible mechanical knock or no-start condition if timing jumped multiple teeth on an interference engine

Most Likely Root Causes

  • Stretched timing chain, worn plastic guides, or collapsed hydraulic chain tensioner (#1 mechanical cause on modern high-mileage engines)
  • Low, neglected, or sludged engine oil starving the VVT cam phaser, or a sticking VVT Oil Control Valve (OCV) (coil spec 6–12 Ω)
  • Jumped timing belt tooth/teeth (or damaged keyway/crank bolt slip after recent belt/water-pump service)
  • Slipped/spun camshaft or crankshaft reluctor tone wheel (or bent trigger tooth), verified decisively on a dual-channel oscilloscope

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Engine Damage Risk

Stop driving aggressively; chain/belt jump bends pistons & valves

Interference engine valve-impact risk
VVT OCV Solenoid Coil Spec

Inspect OCV screen for metal/sludge and verify crisp 12 V actuation

6–12 Ω (typical 12 V spool valve)
Definitive Correlation Test

Separates stretched chain / jumped belt / slipped reluctor from oil drag

Dual-channel scope (CKP vs CMP A)

Commonly Affected Models & Service Bulletins

  • Chevrolet Equinox / Traverse / GM Ecotec 2.4L & 3.6L V6 (timing chain stretch & tensioners)
  • Volkswagen / Audi 2.0T TSI EA888 & BMW N20/N26 (timing chain tensioner & reluctor slip)
  • Hyundai / Kia Theta II, Ford EcoBoost & Honda/Toyota VVT engines (sludged OCVs & timing wear)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Shut off and inspect engine oil dipstick level & condition immediately (low or black sludged oil starves hydraulic tensioners and VVT phasers); note any cold-start timing chain rattle.
  2. 2Remove and inspect the Bank 1 Intake VVT Oil Control Valve (OCV) spool screen for metal/sludge debris, test coil resistance (6–12 Ω), and verify smooth spool snap when pulsed with 12 V (plus check VVT commanded vs actual cam angle on live scan data).
  3. 3Capture a dual-channel oscilloscope waveform comparing CKP vs Bank 1 Intake CMP (`Sensor A`) against a known-good OEM reference—confirming true mechanical phase offset vs sensor dropout—before pulling the timing cover to verify mechanical TDC timing marks.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is the engine oil critically low/sludged, or is the Bank 1 Intake VVT OCV (6–12 Ω) clogged with debris or stuck?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data / bi-directional scanner (Desired vs Actual Cam Phase °)Dual-channel lab oscilloscope (comparing CKP & Bank 1 Intake CMP waveforms)Digital multimeter (6–12 Ω OCV test), engine timing locking pins & torque wrench
  1. 1If engine oil is severely low or sludged and timing marks are intact, perform an engine oil + OEM filter change and inspect/clean or replace a stuck VVT OCV solenoid (`6–12 Ω`).
  2. 2If dual-channel scope traces or physical timing marks confirm mechanical offset, have a qualified technician replace the complete timing chain/belt kit (chain/belt, tensioner, guides, and sprockets/phaser as needed)—never reuse a worn tensioner.
  3. 3If timing marks align yet the reluctor shifted on its shaft, replace the damaged camshaft/crankshaft reluctor or phaser and torque crank pulley bolts strictly to OEM spec.
  4. 4Clear P0016, verify 0° idle phase error (commanded vs actual matches cleanly), and confirm quiet cold starts.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$40 – $220
Professional Repair (Parts + Labor)$650 – $2,400

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: P0016 (Powertrain & Engine Management)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $650 – $2,400

Frequently Asked Questions

Can I keep driving with code P0016?

No—especially not aggressively! Because most modern engines are interference engines, driving with a stretched timing chain, failing tensioner, or jumped timing belt risks skipping additional teeth and bending intake/exhaust valves, turning a timing job into catastrophic engine failure.

Can replacing the camshaft or crankshaft sensor fix P0016?

Almost never. P0016 means both sensors ARE generating signals, and the PCM clearly sees they are out of mechanical time with each other—always inspect oil condition, VVT OCV (6–12 Ω), and physical timing alignment via dual-channel oscilloscope first.

Related Searches & Questions

OBD2 P0016 crankshaft camshaft correlation bank 1 sensor Acan I drive with P0016 bent valvesP0016 timing chain stretched vs VVT solenoid OCVP0016 dual channel oscilloscope CKP CMP waveform

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0016: Crankshaft Position – Camshaft… — Fixes & Cost | FaultCodes.org