# OBD-II P0016: OBD-II P0016: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A)

> **Quick Answer:** Code **P0016** (SAE J2012) means the **crankshaft and Bank 1 intake camshaft (`Sensor A`) are mechanically out of phase correlation**. **CRITICAL SAFETY WARNING:** Most modern engines are **interference designs**—**stop driving aggressively and avoid high RPM** (have the vehicle inspected promptly or towed if chain rattle/rough running is present) because jumping one more tooth can bend valves and destroy the engine! Always check **engine oil level, sludge, and the VVT Oil Control Valve (OCV) solenoid (`6–12 Ω` coil)** first, then inspect for a **stretched timing chain, jumped timing belt teeth, collapsed hydraulic tensioner, or slipped reluctor wheel** using a **dual-channel oscilloscope** ($40–$220 DIY sensor/OCV checks; $650–$2,400 professional timing chain/belt overhaul).

- **URL:** https://faultcodes.org/automotive/obd2-p0016
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Powertrain & Engine Management
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Professional Recommended
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
The PCM continuously compares the phase angle between the Crankshaft Position (CKP) trigger wheel and Bank 1 Intake Camshaft Position (CMP "A") signal against stored base timing (`0°` parked phase). Even a **one-tooth timing chain stretch/jump**, a sticky oil-sludged **VVT phaser/OCV**, or a spun camshaft reluctor tone wheel shifts cam-to-crank alignment past the OEM tolerance threshold and triggers `P0016`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Engine Damage Risk | Interference engine valve-impact risk | Stop driving aggressively; chain/belt jump bends pistons & valves |
| VVT OCV Solenoid Coil Spec | 6–12 Ω (typical 12 V spool valve) | Inspect OCV screen for metal/sludge and verify crisp 12 V actuation |
| Definitive Correlation Test | Dual-channel scope (CKP vs CMP A) | Separates stretched chain / jumped belt / slipped reluctor from oil drag |

## Commonly Affected Models & Service Bulletins
- Chevrolet Equinox / Traverse / GM Ecotec 2.4L & 3.6L V6 (timing chain stretch & tensioners)
- Volkswagen / Audi 2.0T TSI EA888 & BMW N20/N26 (timing chain tensioner & reluctor slip)
- Hyundai / Kia Theta II, Ford EcoBoost & Honda/Toyota VVT engines (sludged OCVs & timing wear)

## Common Symptoms
- Metallic **timing chain rattle on cold startup**, rough idle, stalling, or severe power loss
- Extended cranking before startup and illuminated Check Engine Light (`P0016`, often paired with `P0011` or `P0017`)
- Audible mechanical knock or no-start condition if timing jumped multiple teeth on an interference engine

## Most Likely Root Causes
- **Stretched timing chain, worn plastic guides, or collapsed hydraulic chain tensioner** (#1 mechanical cause on modern high-mileage engines)
- **Low, neglected, or sludged engine oil** starving the VVT cam phaser, or a sticking **VVT Oil Control Valve (OCV)** (coil spec `6–12 Ω`)
- **Jumped timing belt tooth/teeth** (or damaged keyway/crank bolt slip after recent belt/water-pump service)
- **Slipped/spun camshaft or crankshaft reluctor tone wheel** (or bent trigger tooth), verified decisively on a **dual-channel oscilloscope**

## Tools & Parts Reference
- OBD-II live-data / bi-directional scanner (**Desired vs Actual Cam Phase °**)
- **Dual-channel lab oscilloscope** (comparing CKP & Bank 1 Intake CMP waveforms)
- Digital multimeter (`6–12 Ω` OCV test), engine timing locking pins & torque wrench

## Step-by-Step Troubleshooting & Fix
1. If engine oil is severely low or sludged and timing marks are intact, perform an engine oil + OEM filter change and inspect/clean or replace a stuck **VVT OCV solenoid (`6–12 Ω`)**.
2. If dual-channel scope traces or physical timing marks confirm mechanical offset, have a qualified technician replace the **complete timing chain/belt kit** (chain/belt, tensioner, guides, and sprockets/phaser as needed)—never reuse a worn tensioner.
3. If timing marks align yet the reluctor shifted on its shaft, replace the damaged **camshaft/crankshaft reluctor or phaser** and torque crank pulley bolts strictly to OEM spec.
4. Clear `P0016`, verify `0°` idle phase error (`commanded vs actual` matches cleanly), and confirm quiet cold starts.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $40–$220 | $650–$2400 |
| GBP | £32–£175 | £500–£1850 |
| CAD | CA$55–CA$290 | CA$850–CA$3100 |
| EUR | €38–€200 | €580–€2150 |
| CHF | CHF 45–CHF 240 | CHF 780–CHF 2750 |

## Frequently Asked Questions
### Can I keep driving with code P0016?
No—especially not aggressively! Because most modern engines are **interference engines**, driving with a stretched timing chain, failing tensioner, or jumped timing belt risks skipping additional teeth and **bending intake/exhaust valves**, turning a timing job into catastrophic engine failure.

### Can replacing the camshaft or crankshaft sensor fix P0016?
Almost never. `P0016` means both sensors ARE generating signals, and the PCM clearly sees they are **out of mechanical time with each other**—always inspect oil condition, VVT OCV (`6–12 Ω`), and physical timing alignment via dual-channel oscilloscope first.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
