FaultCodes.org
P0174OBD-IIFuel Trim & Air/O2 MeteringVerified Guide· Updated: Nov 22, 2026

OBD-II P0174: System Too Lean (Bank 2)

SAE J2012 code set when Long Term Fuel Trim exceeds roughly +20% to +25% trying to keep Bank 2 (opposite cylinder #1) at 14.7:1—compare freeze-frame idle vs 2,500 RPM trims and whether P0171 co-occurs.

Quick AnswerModerate — Plan Repair

Code P0174 (SAE J2012) means the PCM detected a System Too Lean on Bank 2 (the cylinder bank not containing cylinder #1 on V6/V8 engines), typically setting once adaptive Long Term Fuel Trim (`LTFT`) or `LTFT + STFT` exceeds `+20% to +25%` above stoichiometric 14.7:1 fueling. First check whether P0171 (Bank 1) appears alongside P0174: both codes together point to a shared MAF sensor, main intake/PCV vacuum leak, or weak fuel pressure, whereas P0174 alone isolates Bank 2 intake manifold gaskets, injectors, or pre-O2 exhaust leaks. Watch trims in freeze frame—leaks that spike high at idle yet drop near 0% at ~2,500 RPM confirm a vacuum leak ($15–$190 DIY; $130–$520 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$130 – $520

What This Fault Code Means

To maintain a 14.7:1 stoichiometric burn for three-way catalytic conversion, the ECM monitors upstream Bank 2 oxygen sensors continuously via Short Term Fuel Trim (STFT) and long-term adaptive learning (LTFT). Either unmetered air sneaking past the Mass Air Flow (MAF) sensor, false oxygen entering an upstream exhaust crack, or insufficient fuel delivery pushes LTFT past +20–25% until P0174 turns on the Check Engine Light.

Common Symptoms

  • Rough or stumbling idle that partially smooths out at steady highway speed (classic vacuum leak signature)
  • Hesitation under throttle acceleration, sluggish uphill pull, or occasional cold-start stalling
  • Check Engine Light with P0174 alone—or P0171 + P0174 stored together on V6/V8 engines

Most Likely Root Causes

  • Dry-rotted rubber PCV hoses, cracked air intake boot, or leaking Bank 2 intake manifold gasket (vacuum leak)
  • Contaminated or oil-coated Mass Air Flow (MAF) sensor under-reporting incoming air mass (often triggers P0171 + P0174)
  • Pre-catalyst Bank 2 exhaust manifold / flange leak pulling outside oxygen past the upstream O2 sensor
  • Low fuel rail pressure (weak fuel pump/clogged filter) or clogged Bank 2 fuel injectors / skewed Bank 2 upstream O2 sensor

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Typical Lean Trim Threshold

Sustained positive correction over calibrated steady-state drive cycle

LTFT > +20% to +25% (or LTFT+STFT > +25%)
Target Stoichiometric Ratio

Gasoline stoichiometric reference controlled by upstream O2 feedback

14.7:1 AFR (λ = 1.00)
Vacuum Leak vs MAF/Fuel Check

Trims drop at 2,500 RPM for vacuum leaks; stay high under load for MAF/fuel

Idle vs ~2,500 RPM trim comparison
Bank Identification Rule

Applies to V-engines & dual-bank layouts; P0174+P0171 implies shared fault

Opposite Cylinder #1 (SAE J2012)

Commonly Affected Models & Service Bulletins

  • V6 & V8 Gasoline Vehicles with Dual-Bank Exhaust (Ford F-150 / Explorer / Mustang, Chevrolet Silverado / Tahoe, Toyota Tacoma / Tundra / 4Runner)
  • BMW & Mercedes-Benz Inline-6 / V6 / V8 Dual-Bank Engines
  • Audi / Volkswagen / Porsche V6 & V8 Engines (SAE J2012 / EOBD Compliant)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read Freeze Frame & stored DTCs first: check if P0171 accompanies P0174 (global airflow/fuel issue vs Bank 2-only leak), and compare LTFT + STFT at idle against steady `~2,500 RPM`.
  2. 2Trims that drop sharply toward 0% at 2,500 RPM prove an unmetered vacuum leak; trims that stay +20% or climb under high RPM load implicate a dirty/faulty MAF sensor or low fuel pressure.
  3. 3Run a low-pressure intake smoke test (and inspect Bank 2 exhaust flange soot/ticking ahead of Sensor 1), clean the MAF only with MAF-safe cleaner, and check fuel rail pressure against OEM bar/psi specs.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Do BOTH P0171 (Bank 1) and P0174 (Bank 2) appear together, AND do trims stay elevated above +20% at 2,500 RPM?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data scanner (monitoring STFT / LTFT Bank 1 & Bank 2 + MAF g/s)Dedicated MAF Sensor Cleaner spray (safe for hot-film/wire elements)Automotive intake EVAP/vacuum smoke machine & fuel rail pressure gauge
  1. 1Inspect rubber intake ducts between airbox and throttle body plus PCV lines for cracks, loose clamps, or unseated oil filler caps/dipsticks, replacing split hoses immediately.
  2. 2Spray dedicated MAF Sensor Cleaner gently onto MAF sensing wires/film (never brake cleaner or carb spray!), let dry 15 minutes completely, and inspect live g/s readings.
  3. 3Perform an intake smoke leak test to catch Bank 2 lower/upper intake manifold O-ring leaks or EGR/brake-booster lines; tighten or replace any leaking gaskets.
  4. 4Check upstream Bank 2 exhaust joints for cold ticking leaks (pulling false O2 into exhaust pulses), verify fuel pressure under load, clear codes, and watch combined LTFT + STFT return within ±10%.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$15 – $190
Professional Repair (Parts + Labor)$130 – $520

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Which side of the engine is Bank 2 on a P0174 fault?

Bank 1 always contains cylinder #1 (per SAE J2012), so Bank 2 is simply the opposite cylinder bank on V6, V8, or dual-bank engines. Inline 4-cylinder engines only have Bank 1 and rarely use Bank 2 trims.

Can an exhaust leak really cause lean code P0174?

Yes—between exhaust pulses, low pressure at a cracked Bank 2 manifold or blown flange gasket draws ambient air (21% oxygen) in ahead of the upstream O2 sensor. The ECM sees excess oxygen and adds unnecessary fuel until LTFT exceeds +25%.

Related Searches & Questions

p0174p0174 codep0174 code chevyp0174 fordp0174 code fordp0174 toyotap0174 ford f150p0174 nissanp0174 engine codep0174 and p0171p0174 meaningp0174 code meaning

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0174: System Too Lean (Bank 2) — Causes, Fixes & Cost | FaultCodes.org