FaultCodes.org
F.28VaillantGas Ignition & Flame SensingVerified Guide· Updated: Nov 22, 2026

Vaillant Boiler Fault Code F.28: Ignition Failure Lockout

Vaillant ecoTEC / atmoTEC failed to detect an ionization flame signal after 3 consecutive ignition attempts—caused by interrupted gas supply, empty prepayment credit, frozen condensate pipes, fouled/worn electrodes, air/flue blockage, or gas valve/PCB faults.

Quick AnswerCritical — Stop Immediately

Vaillant fault code F.28 (or F28) means the boiler triggered 3 consecutive ignition attempts without detecting a micro-amp flame ionization signal and locked out safely to prevent unburnt gas buildup. Safely verify that other gas appliances work (plus check prepayment meter credit if applicable), inspect exterior plastic condensate pipes for winter freezing (thaw gently with warm, never boiling water), ensure the outdoor flue terminal isn't blocked, and press Reset once only. If F.28 returns—or if you ever smell gas—do not press Reset repeatedly and do not open the boiler casing; book a certified Gas Safe / HVAC engineer (€0 safe homeowner checks; $140–$560 / £95–£420 professional repair).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Gas Ignition & Flame Sensing
Professional Repair
$140 – $560

What This Fault Code Means

On heat or hot-water demand, the Vaillant PCB opens the gas control valve, triggers the ignition transformer spark across the electrode gap, and measures ionization rectification micro-amps (µA). If zero flame signal returns across three start cycles, F.28 locks the burner off safely.

Common Symptoms

  • Display shows flashing F.28 / F28 with crossed-out flame icon and zero heating or hot water
  • Clicking ignition sparks or three fan start/stop attempts followed by lockout
  • Commonly appears during freezing winter snaps (frozen outdoor condensate line) or after street/meter gas shutoffs

Most Likely Root Causes

  • Interrupted gas supply, closed boiler yellow gas cock, empty prepayment gas meter, or air pocket in pipe after nearby gas maintenance
  • Frozen external plastic condensate drain pipe causing condensate water to back up inside the combustion chamber
  • Pitted, cracked, or carbon-fouled ignition / ionization electrode or frayed high-voltage ignition lead
  • Restricted air intake / flue terminal recirculation, seized/defective gas valve solenoid, low dynamic gas pressure, or PCB failure

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Boiler Ignition Retry Lockout

Locks out safely when zero ionization flame current registers

3 consecutive failed ignition attempts
Flame Detection Principle

Carbon buildup or cracked electrode ceramic breaks flame sensing

Ionization electrode micro-amp (µA) signal
Safe Homeowner Reset Limit

Repeated resets without resolving cause risk unburnt gas buildup

Max 1 single reset check
Common Cold-Weather Cause

Thaw safely outside using warm (never boiling) water

Frozen external condensate pipe (<0 °C)

Commonly Affected Models & Service Bulletins

  • Vaillant ecoTEC plus & ecoTEC pro Wall-Hung Condensing Gas Boilers
  • Vaillant ecoTEC exclusive & ecoCOMPACT Combi/System Units
  • Vaillant atmoTEC / turboTEC Gas Heating Boilers

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Safety Check: If you smell raw gas, do NOT touch electrical switches or reset—shut the emergency gas valve off, ventilate rooms, and call the national gas emergency helpline immediately.
  2. 2Test whether a gas stove/hob ignites normally, verify prepayment meter credit, check that boiler isolation gas taps are open, and inspect exterior condensate discharge pipes in freezing weather.
  3. 3Visually check external wall/roof flue grilles from ground level for snow/leaves/debris and perform 1 single Reset; leave internal gas pressures, electrodes, and valve testing strictly to a certified engineer.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Do other gas appliances (hob/cooker) also fail to light, or is a prepayment gas meter out of credit?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Warm (non-boiling) water bottle or jug (external condensate pipe thawing only)Certified engineer calibrated gas manometer (standing & working mbar/kPa)Certified engineer combustion gas analyzer & OEM Vaillant electrode set
  1. 1Confirm active household gas supply (check other gas appliances, emergency shutoff, and prepayment credit).
  2. 2If sub-zero weather froze an exterior plastic condensate pipe, gently pour warm (never boiling) water along the pipe or hold a hot-water bottle against the frozen elbow to thaw it cleanly.
  3. 3Press the Vaillant crossed-flame Reset button once cleanly and listen for normal ignition.
  4. 4If F.28 locks out again immediately: stop pressing Reset and call a certified gas heating engineer to inspect/clean or replace worn ignition & ionization electrodes, verify ignition cable insulation, measure dynamic standing & working gas pressures, test gas valve solenoids, and check PCB outputs.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0
Professional Repair (Parts + Labor)$140 – $560

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: Vaillant F.28 (Gas Ignition & Flame Sensing)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $140 – $560

Frequently Asked Questions

How many times is it safe to press Reset for Vaillant F.28?

Vaillant and Gas Safe engineers advise resetting at most once after confirming gas supply and thawing any frozen condensate pipe—repeated resets can accumulate unburnt gas or mask unsafe flue/valve faults.

What is the difference between Vaillant F.28 and F.29?

F.28 fails to establish a flame during initial ignition start-up (3 failed attempts), whereas F.29 ignites cleanly first and then loses its flame during active running.

Related Searches & Questions

vaillant f28 fault codevaillant f28vaillant f28 faultvaillant f28 fault code how to fixvaillant f28 errorvaillant f28 f29vaillant f28 codevaillant f28 and f54vaillant f28 fault resetvaillant f28 low pressurevaillant f28 meaningvaillant boiler f28 meaning

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

HVAC & Boilers →
Vaillant Boiler Fault Code F.28: Ignition Failure Lockout | FaultCodes.org