FaultCodes.org
E9Worcester BoschOverheat Protection & CirculationVerified Guide· Updated: Nov 22, 2026

Worcester Bosch E9 Fault Code: Central Heating Overheat Safety Limiter (105 °C)

High-limit lockout triggered when the central heating flow Safety Temperature Limiter exceeds 105 °C (often logged with sub-codes 219, 220, 221, or 224)—check cold pressure (1.0–1.5 bar) and open valves, then book a Gas Safe engineer.

Quick AnswerCritical — Stop Immediately

Fault code E9 on Worcester Bosch Greenstar (and Bosch/Junkers Condens) boilers signals a critical overheat safety lockout: the central heating flow Safety Temperature Limiter (STB) exceeded its absolute trip threshold of `105 °C` and shut down the gas valve (often accompanied by diagnostic sub-codes `219`, `220`, `221`, or `224`). Safely inspect the cold pressure gauge (1.0–1.5 bar target), verify radiator valves are open, wait for the unit to cool, and press Reset once—if E9 repeats or boiler pressure stays normal, keep the cover closed and contact a Gas Safe registered engineer to clear trapped air, descale the primary heat exchanger, test the pump/diverter valve, or replace the thermal limiter ($140–$550 / £95–£410).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Overheat Protection & Circulation
Professional Repair
$140 – $550

What This Fault Code Means

A central heating flow Safety Temperature Limiter sits directly on the primary circuit to guarantee water never flashes into uncontrolled steam inside the Greenstar heat exchanger. If circulation stops—through trapped air, low water pressure, hard-water limescale buildup, or a failing circulation pump—flow temperature shoots past 105 °C, locking out on E9 until manually diagnosed and cooled.

Common Symptoms

  • Boiler shuts off completely displaying E9 (with optional sub-code 219–224 on service screens) and ceases heating/hot water
  • Loud kettling, hissing, or banging noises inside the cabinet right before shutdown
  • Boiler refuses to clear permanently on Reset because internal overheating or limiter latching triggers again rapidly

Most Likely Root Causes

  • Trapped air lock or low system water pressure (< 1.0 bar) starving primary heat exchanger circulation
  • Heavy limescale or magnetite sludge buildup creating localized > 105 °C metal hot spots inside the heat exchanger
  • Seized, underperforming, or dead heating circulation pump or stuck diverter valve
  • Faulty central heating flow Safety Temperature Limiter (STB) or damaged limiter wiring harness

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Safety Temperature Limiter Trip Point

Hard cutoff protecting Greenstar heat exchanger against boiling

105 °C (CH flow pipe)
Associated Greenstar Sub-Codes

Differentiate heat exchanger overheat vs limiter/sensor circuit fault

219 / 220 / 221 / 224
Normal Cold Gauge Pressure

Homeowner may only top up external loop and attempt one cool reset

1.0–1.5 bar
Casing & Repair Restriction

Room-sealed combustion cover must never be removed by homeowners

Gas Safe / Certified Engineer Only

Commonly Affected Models & Service Bulletins

  • Worcester Bosch Greenstar i / Si / CDi / Ri Condensing Boilers
  • Worcester Bosch Greenstar 2000 / 4000 / 8000 Life & Style Series
  • Bosch / Junkers Cerapur & Condens Boilers (equivalent `E9` overheat code)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Homeowner safe check only: read the front cold pressure gauge (1.0–1.5 bar target—repressurize via key/filling link only if under 1.0 bar) and make sure radiator lockshields/TRVs aren't all closed.
  2. 2Wait 20 minutes for internal pipes to cool, note any displayed 3-digit sub-code (219, 220, 221, 224) for the engineer, and perform one single Reset—never repeatedly reset an overheat lockout.
  3. 3Gas Safe / certified engineer diagnostics: test heat-exchanger pressure/flow (ΔT), verify pump speed and bleed air at the primary exchanger, check heat exchanger scaling (219–224), and measure cold continuity on the 105 °C STB cutout.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Was cold boiler pressure under 1.0 bar or were all heating zone/radiator valves closed?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Filling key / external filling link (homeowner cold-pressure adjustment only)Certified engineer: Gas Safe calibrated multimeter, pump test leads & flue analyzerCertified engineer: OEM Worcester Bosch 105 °C STB limiter & chemical descaler
  1. 1Check cold boiler gauge pressure; if below 1.0 bar, safely top up to 1.0–1.5 bar using the external or keyless filling link and vent cool radiators (re-checking gauge).
  2. 2Confirm open circulation by leaving at least 2–3 radiator valves fully open, wait until cooled down, and perform one single reset.
  3. 3If E9 immediately re-locks or pressure was already 1.0–1.5 bar, turn off electrical power to the boiler and call a Gas Safe registered / certified heating engineer—never open a sealed Greenstar cover yourself.
  4. 4The engineer replaces or unsticks a failed circulation pump / diverter valve, power-flushes or chemically descales the primary heat exchanger, clears trapped air, and replaces any faulty 105 °C safety limiter.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0
Professional Repair (Parts + Labor)$140 – $550

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: Worcester Bosch E9 (Overheat Protection & Circulation)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $140 – $550

Frequently Asked Questions

What do Worcester Bosch E9 sub-codes 219, 220, 221, or 224 mean?

They pinpoint the exact overheat channel inside Greenstar diagnostics—distinguishing between a genuine flow-pipe temperature spike above 105 °C, primary heat-exchanger scaling, or an open-circuit safety temperature limiter / sensor wiring fault.

Can a DIY homeowner fix Worcester Bosch fault E9 without calling an engineer?

Only if the sole trigger was low water pressure (< 1.0 bar) or closed radiator valves fixed by filling back to 1.0–1.5 bar and pressing Reset once. Any persistent E9 requires a Gas Safe engineer because Greenstar casings form the room-sealed combustion enclosure.

Related Searches & Questions

Worcester Bosch E9 fault code 105 degreesWorcester Bosch Greenstar E9 219 220 221 224Worcester E9 reset overheat costBosch Condens E9 Störung

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

HVAC & Boilers →
Worcester Bosch E9 Fault Code: Central Heating… — Fixes & Cost | FaultCodes.org