FaultCodes.org

Home Appliances

Washer, dryer, dishwasher, and fridge fault codes for Bosch, Siemens, Miele, Samsung, LG, and Whirlpool.

15 codes indexed
E18Bosch / Siemens

Bosch / Siemens Washing Machine Drain Error E18 (F18 / d02)

Drain pump timeout triggered after failing to empty the drum cleanly—officially traced to a clogged front-bottom coin-trap pump filter, jammed pump impeller, kinked rear drain hose, or unremoved sink-siphon knockout plug.

E15Bosch / Siemens

Bosch / Siemens Dishwasher E15 Error (AquaStop Base Flood Triggered)

Water accumulated in the bottom base tray and lifted the AquaStop styrofoam float switch—locking out wash cycles with the water-tap icon until dried, most commonly resolved by installing BSH Sump Seal Repair Kit #12005744.

OELG

LG Washing Machine Drain Error (OE — Outlet Error)

LG washer 'Outlet Error' triggered after failing to drain tub water within the ~10-minute cycle window—officially traced to clogged bottom-left coin traps, jammed pump impellers, rear hose kinks (<4 in wall clearance), or household plumbing clogs.

UELG

LG Washing Machine Unbalanced Load Error (UE / uE)

LG detected uneven drum weight distribution or machine cabinet wobble before high-speed spinning (`uE` auto-balancing vs `UE` cycle stop)—solved by redistributing ~2/3 drum loads, tightening leveling feet lock nuts, or inspecting worn shock absorbers.

4ESamsung

Samsung Washing Machine Water Supply Error (4E / 4C)

Washer failed to reach target water level within the fill timeout—most commonly solved by opening both supply taps fully, scrubbing clogged inlet hose mesh filters (recommended twice yearly), avoiding 'Flood Safe' hoses, or replacing the water inlet valve.

F11Miele

Miele Dishwasher Water Drainage Error (F11)

Dishwasher failed to drain sump water within timeout—most famously solved per Miele guidelines by clearing the triple-filter combo, lifting the non-return check valve to free glass/debris from the pump impeller, and snapping the check valve vertically straight back in.

LELG

LG Washer Error LE: Locked Motor / Rotor Position Sensor Fault

Main PCB failed to detect expected drum rotation from the Hall Rotor Position Sensor (RPS)—test stator phase coils (5–15 Ω), Hall sensor pins (5–15 kΩ), and clear overload or suds lock.

5ESamsung

Samsung Washer Error 5E / SE / 5C: Water Drain Timeout

Washer failed to empty the tub within the allowed drain window—clean the lower-front debris filter, inspect pump impeller blades, and verify official `60–90 cm` (`24–35 in`) standpipe hose height.

DCSamsung

Samsung Washer Error DC / Ub / UE: Unbalanced Load or Door Lock Interlock

Control board halted spin acceleration after detecting severe drum vibration (`DC` / `Ub` / `UE`) or an unlatched door state (`dC`)—redistribute tangled laundry, level feet on solid flooring, and run Calibration Mode.

E09Bosch / Siemens

Bosch / Siemens Dishwasher E09: Circulation Heat Pump Heater Failure

BSH dishwashers combine the heating element directly inside the circulation pump—`E09` triggers when heater coil resistance falls outside ~20–25 Ω (usually `OL` open circuit), harness pins melt, or the board heater relay fails.

E24Bosch / Siemens

Bosch / Siemens Dishwasher E24: Drain Hose, Siphon or Pump Cover Blocked

Washer failed to evacuate sump water in time (paired closely with `E25`)—check kinked hose, under-sink siphon spigot or garbage-disposal knockout plug, and click the white sump drain pump cover firmly locked.

F5 E2Whirlpool

Whirlpool Washer Error F5 E2: Door / Lid Lock Switch Failure

Main control board (CCU/ACU) commanded door lock yet failed to receive closed switch feedback—clear trapped gasket obstructions, power-reset 5 minutes, and test lock solenoid coil (`50–1,500 Ω`) plus switch continuity (`0–5 Ω`).

E19Bosch / Siemens

Bosch / Siemens Dishwasher E19: Heat Exchanger Drain Valve Coil Fault

BSH dishwashers log `E19` when the heat-exchanger outlet valve or dispenser coil fails—ohm-test behind the left side panel (`~7.5 kΩ` for blue-plug DC valves, `~2.2 kΩ` for pink-plug pre-2016 AC valves, or `7.5–11.5 kΩ` dispenser coil).

F20Miele

Miele Washer / Dishwasher Fault F20: Heating System & NTC Timeout

Water failed to reach target temperature before Miele's Thermostop deadline—power off `≥ 2 min` to reset capacitors, then ohm-test the **NTC sensor (`14.9 kΩ` at `20 °C` / `12.0 kΩ` at `25 °F`/`25 °C`)**, **heater (`20–50 Ω`)**, chassis insulation, and `K1-1` relay.

F9 E1Whirlpool

Whirlpool Washer Error F9 E1: Long Drain Timeout (8–10 Minutes)

Washer failed to pump water down within Whirlpool's `8–10 minute` drain window—clean the coin trap & sump hose, verify standpipe height (`30–96 in` / max `4.5 in` hose depth), and ohm-test the drain pump (`14–25 Ω`).

Home Appliances — FaultCodes.org | FaultCodes.org