Samsung Washer Error DC / Ub / UE: Unbalanced Load or Door Lock Interlock
Control board halted spin acceleration after detecting severe drum vibration (DC / Ub / UE) or an unlatched door state (dC)—redistribute tangled laundry, level feet on solid flooring, and run Calibration Mode.
Samsung washer code DC (closely paired with Ub / UE / Ur load-imbalance alerts on top-loaders, and also indicating Door Check `dC` on newer front-loaders) means the controller blocked high-speed spin due to an off-balance drum or an open/unconfirmed door latch. Stop the cycle, detangle heavy wet jeans/towels evenly around the tub, verify the cabinet sits rock-solid with lock nuts tightened directly on the floor (never on uncertified rolling dollies), close the door firmly until it clicks, and run Calibration Mode with an empty drum. Balancing and leveling cost $0 DIY; replacing worn suspension rods/shock absorbers or a door latch switch runs ~$25–$65 DIY ($120–$230 pro).
- Safe to Operate?
- Yes (Short Term)
- DIY Difficulty
- Easy (Basic Tools)
- System
- Drum Balance & Door Lock
- Professional Repair
- $120 – $230
What This Fault Code Means
During spin ramp-up, Samsung's inverter PCB monitors motor current ripple and accelerometer feedback—first shifting into an automatic balance retry loop (Ur) and then stopping with DC / Ub / UE if laundry clumps to one wall. On AddWash/EcoBubble front-loaders (dC), the board also displays a Door Check fault if the main door or AddDoor magnetic switch fails to signal locked status.
Common Symptoms
- Timer hangs around
9–13minutes remaining while drum rocks back and forth (Urretry) before stopping withDC/Ub - Violent drum banging against cabinet walls or machine walking across the laundry room floor
- Front-load washer refuses to start/spin and flashes
DC/dCimmediately after closing the main door or AddDoor
Most Likely Root Causes
- Clumped heavy single item (bath mat, heavy duvet, tangled fitted sheet, or one jacket washed alone)
- Unlevel washer feet, soft/springy flooring, or third-party rolling washer trolleys/stands amplifying vibration
- Partially open main door, AddWash mini-door latch misaligned, or failing door lock switch (
dCon front-loaders) - Worn suspension rods (top-loaders) or tired shock absorbers / spring dampers causing empty-drum balance errors
Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold |
|---|---|
| Related Balance / Retry Codes Control runs Ur water-rebalance cycles before halting on DC/Ub | DC / Ub / UE (Retry: Ur) |
| Front-Load Variant Meaning Check main door & AddDoor closure if fault stops before spin | dC (Door Check / Interlock) |
| Cabinet Leveling Tolerance Samsung advises directly on solid floor without aftermarket wheeled trolleys | 0 mm diagonal rock + locked jam nuts |
| Post-Leveling Setup Re-learns empty drum weight baseline after suspension or leveling work | 1–2 min unplug + Calibration Mode |
Commonly Affected Models & Service Bulletins
- Samsung Top-Load ActiveWaterJet & VRT Plus Washers (WA45 / WA50 / WA54 Series)
- Samsung EcoBubble & QuickDrive Front-Load Washers (WW / WF Series)
- Samsung Bespoke AI Washers & Washer-Dryer Combos
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Confirm whether the machine was spinning (
DCload imbalance /Ub/UE) or refusing to start right after pressing Start (dCdoor-open check on front-loaders). - 2Press corners diagonally across the top lid/frame: any rocking shows uneven leveling feet; verify the machine rests solidly on hard flooring rather than a third-party rolling stand.
- 3Empty the drum completely and test a high-speed Spin Only cycle (plus Samsung Calibration Mode) to isolate wet-laundry distribution from mechanical suspension or door-latch faults.
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Does the washer spin smoothly when clothes are loosely mixed/redistributed or when spun completely empty?
Step-by-Step Troubleshooting & Fix
Tools & Parts Reference
dC door-lock microswitch diagnosis is needed)OEM suspension rod set (4x) or shock absorber pair (if suspension sags)- 1Open the washer, loosen tangled towels/sheets, add 2–3 medium items when washing single bulky blankets so weight distributes evenly, and never overload past ~75–80% tub volume.
- 2Adjust the four leveling feet with a wrench until centered by bubble level and lock their jam nuts tight up against the cabinet base; remove unapproved wheeled trolleys/sliders.
- 3For front-loaders displaying
dC, remove stray fabric from the rubber door boot, press both the main door and AddDoor firmly until latched, and ohm-test the door switch if the latch fails to lock. - 4Unplug for 1–2 minutes to clear board memory, run Calibration Mode on an empty tub, and replace weak top-loader suspension rods (
x4kit) or front-load shock absorbers if even balanced/empty loads still bounce and triggerDC.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $0 – $65 |
| Professional Repair (Parts + Labor) | $120 – $230 |
Recommended Diagnostic Tools & Replacement Parts
Check OEM specifications and compatible tools for this repair.
Frequently Asked Questions
Why does Samsung DC mean unbalanced load on some washers and door open on others?
Across older and top-load Samsung models, DC stands for unbalanced drum load (alongside Ub/UE and retry loop Ur), whereas newer EcoBubble/AddWash front-loaders display dC for Door Check alongside UB/UE for imbalance.
Why does Samsung advise against sliding rollers or aftermarket stands?
Rubber caster pads and thin metal rolling pedestals flex at high spin RPMs, tricking the vibration algorithm into reading constant imbalance (DC/Ub) and shortening suspension life.