# Samsung DC: Samsung Washer Error DC / Ub / UE: Unbalanced Load or Door Lock Interlock

> **Quick Answer:** Samsung washer code **DC** (closely paired with **Ub / UE / Ur** load-imbalance alerts on top-loaders, and also indicating Door Check **`dC`** on newer front-loaders) means the controller blocked high-speed spin due to an **off-balance drum** or an **open/unconfirmed door latch**. Stop the cycle, detangle heavy wet jeans/towels evenly around the tub, verify the cabinet sits rock-solid with lock nuts tightened directly on the floor (never on uncertified rolling dollies), close the door firmly until it clicks, and run **Calibration Mode** with an empty drum. Balancing and leveling cost $0 DIY; replacing worn suspension rods/shock absorbers or a door latch switch runs ~$25–$65 DIY ($120–$230 pro).

- **URL:** https://faultcodes.org/appliances/samsung-dc
- **Category:** Home Appliances
- **Brand / Standard:** Samsung
- **System Area:** Drum Balance & Door Lock
- **Severity:** Low — Minor Issue
- **Safe to Operate?:** Yes (Short Term)
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
During spin ramp-up, Samsung's inverter PCB monitors motor current ripple and accelerometer feedback—first shifting into an automatic balance retry loop (`Ur`) and then stopping with `DC` / `Ub` / `UE` if laundry clumps to one wall. On AddWash/EcoBubble front-loaders (`dC`), the board also displays a Door Check fault if the main door or AddDoor magnetic switch fails to signal locked status.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Related Balance / Retry Codes | DC / Ub / UE (Retry: Ur) | Control runs Ur water-rebalance cycles before halting on DC/Ub |
| Front-Load Variant Meaning | dC (Door Check / Interlock) | Check main door & AddDoor closure if fault stops before spin |
| Cabinet Leveling Tolerance | 0 mm diagonal rock + locked jam nuts | Samsung advises directly on solid floor without aftermarket wheeled trolleys |
| Post-Leveling Setup | 1–2 min unplug + Calibration Mode | Re-learns empty drum weight baseline after suspension or leveling work |

## Commonly Affected Models & Service Bulletins
- Samsung Top-Load ActiveWaterJet & VRT Plus Washers (WA45 / WA50 / WA54 Series)
- Samsung EcoBubble & QuickDrive Front-Load Washers (WW / WF Series)
- Samsung Bespoke AI Washers & Washer-Dryer Combos

## Common Symptoms
- Timer hangs around `9–13` minutes remaining while drum rocks back and forth (`Ur` retry) before stopping with `DC` / `Ub`
- Violent drum banging against cabinet walls or machine walking across the laundry room floor
- Front-load washer refuses to start/spin and flashes `DC` / `dC` immediately after closing the main door or AddDoor

## Most Likely Root Causes
- Clumped heavy single item (bath mat, heavy duvet, tangled fitted sheet, or one jacket washed alone)
- Unlevel washer feet, soft/springy flooring, or third-party **rolling washer trolleys/stands** amplifying vibration
- Partially open main door, AddWash mini-door latch misaligned, or failing **door lock switch** (`dC` on front-loaders)
- Worn **suspension rods** (top-loaders) or tired **shock absorbers / spring dampers** causing empty-drum balance errors

## Tools & Parts Reference
- Bubble carpenter level & open-end wrench (adjust & lock foot jam nuts)
- Multimeter (if front-load `dC` door-lock microswitch diagnosis is needed)
- OEM suspension rod set (4x) or shock absorber pair (if suspension sags)

## Step-by-Step Troubleshooting & Fix
1. Open the washer, loosen tangled towels/sheets, add 2–3 medium items when washing single bulky blankets so weight distributes evenly, and never overload past ~75–80% tub volume.
2. Adjust the four **leveling feet** with a wrench until centered by bubble level and lock their jam nuts tight up against the cabinet base; remove unapproved wheeled trolleys/sliders.
3. For front-loaders displaying `dC`, remove stray fabric from the rubber door boot, press both the main door and AddDoor firmly until latched, and ohm-test the door switch if the latch fails to lock.
4. Unplug for 1–2 minutes to clear board memory, run **Calibration Mode** on an empty tub, and replace weak top-loader suspension rods (`x4` kit) or front-load shock absorbers if even balanced/empty loads still bounce and trigger `DC`.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$65 | $120–$230 |
| GBP | £0–£55 | £95–£185 |
| CAD | CA$0–CA$85 | CA$155–CA$295 |
| EUR | €0–€60 | €110–€210 |
| CHF | CHF 0–CHF 80 | CHF 155–CHF 290 |

## Frequently Asked Questions
### Why does Samsung DC mean unbalanced load on some washers and door open on others?
Across older and top-load Samsung models, `DC` stands for unbalanced drum load (alongside `Ub`/`UE` and retry loop `Ur`), whereas newer EcoBubble/AddWash front-loaders display `dC` for Door Check alongside `UB`/`UE` for imbalance.

### Why does Samsung advise against sliding rollers or aftermarket stands?
Rubber caster pads and thin metal rolling pedestals flex at high spin RPMs, tricking the vibration algorithm into reading constant imbalance (`DC`/`Ub`) and shortening suspension life.


## Verified Official & Engineering References
- [Samsung Support US: Washer Error Codes DC, Ub & UE](https://www.samsung.com/us/support/) (Official Support)
- [Samsung Support Deutschland: Waschmaschine Fehlercode DC / UE](https://www.samsung.com/de/support/) (Official Support)
- [Samsung UK Support: Spin Balance & Calibration Troubleshooting](https://www.samsung.com/uk/support/home-appliances/) (Official Support)
