# FaultCodes.org > Independent Technical Diagnostic & Repair Reference. Plain-English root causes, safe-to-operate ratings, interactive symptom triage, and realistic repair cost estimates across 18,900+ automotive, appliance, boiler, and tech codes. Total diagnostic fault codes in database: 18968 Verified in-depth diagnostic guides: 100 Language: en ## Citation & API Format - Clean Markdown endpoint for every fault code: `https://faultcodes.org/api/codes/{slug}/markdown` - Structured Schema.org JSON-LD (`TechArticle`, `HowTo`, `FAQPage`, `SpeakableSpecification`, `DefinedTerm`) embedded on all fault code pages - Includes verified engineering thresholds, repair cost benchmarks, and manufacturer/SAE/norm references ## Categories - [Automotive & OBD-II](https://faultcodes.org/automotive): Diagnostic trouble codes (P, B, C, U) for Ford, Toyota, BMW, VW, GM, and generic SAE J2012 vehicles with repair cost ranges. (18923 codes) - [Home Appliances](https://faultcodes.org/appliances): Washer, dryer, dishwasher, and fridge fault codes for Bosch, Siemens, Miele, Samsung, LG, and Whirlpool. (15 codes) - [HVAC, Boilers & Heating](https://faultcodes.org/hvac): Boiler, heat pump, and furnace error codes for Vaillant, Viessmann, Buderus, Worcester Bosch, and Carrier systems. (15 codes) - [Windows, Gaming & Tech](https://faultcodes.org/software): Windows Update, BSOD stop codes, PlayStation, Xbox, and network error diagnostics with verified troubleshooting steps. (15 codes) ## Brand & System Diagnostic Hubs - [OBD-II (Auto & OBD-II)](https://faultcodes.org/automotive/obd-ii): 9533 codes (e.g. P0420, P0300, P0171) - [Windows (Tech & OS)](https://faultcodes.org/software/windows): 8 codes (e.g. 0x80070005, IRQL_NOT_LESS_OR_EQUAL, MEMORY_MANAGEMENT) - [Bosch / Siemens (Appliances)](https://faultcodes.org/appliances/bosch-siemens): 5 codes (e.g. E18, E15, E09) - [Vaillant (HVAC & Boilers)](https://faultcodes.org/hvac/vaillant): 5 codes (e.g. F.28, F.22, F.29) - [PlayStation 5 (Tech & OS)](https://faultcodes.org/software/playstation-5): 4 codes (e.g. CE-108262-9, CE-108255-1, NW-102216-2) - [Buderus (HVAC & Boilers)](https://faultcodes.org/hvac/buderus): 3 codes (e.g. 3Y, 6A, H07) - [LG (Appliances)](https://faultcodes.org/appliances/lg): 3 codes (e.g. OE, UE, LE) - [Samsung (Appliances)](https://faultcodes.org/appliances/samsung): 3 codes (e.g. 4E, 5E, DC) - [Viessmann (HVAC & Boilers)](https://faultcodes.org/hvac/viessmann): 3 codes (e.g. F4, F2, F5) - [Daikin (HVAC & Boilers)](https://faultcodes.org/hvac/daikin): 2 codes (e.g. U4, A5) - [Miele (Appliances)](https://faultcodes.org/appliances/miele): 2 codes (e.g. F11, F20) - [Whirlpool (Appliances)](https://faultcodes.org/appliances/whirlpool): 2 codes (e.g. F5 E2, F9 E1) - [Worcester Bosch (HVAC & Boilers)](https://faultcodes.org/hvac/worcester-bosch): 2 codes (e.g. EA, E9) - [Xbox (Tech & OS)](https://faultcodes.org/software/xbox): 2 codes (e.g. 0x800705b4, 0x87e10bc6) - [macOS (Tech & OS)](https://faultcodes.org/software/macos): 1 codes (e.g. -36) - [Powertrain & Engine Management (Auto & OBD-II)](https://faultcodes.org/automotive/powertrain-engine-management): 13835 codes - [CAN Bus & Network Communication (Auto & OBD-II)](https://faultcodes.org/automotive/can-bus-network-communication): 1533 codes - [Body Control, Airbag & Comfort (Auto & OBD-II)](https://faultcodes.org/automotive/body-control-airbag-comfort): 1488 codes - [Chassis, ABS & Stability Control (Auto & OBD-II)](https://faultcodes.org/automotive/chassis-abs-stability-control): 1113 codes - [Transmission & Drivetrain (Auto & OBD-II)](https://faultcodes.org/automotive/transmission-drivetrain): 500 codes - [Ignition & Misfire System (Auto & OBD-II)](https://faultcodes.org/automotive/ignition-misfire-system): 260 codes - [Fuel Trim & Air/O2 Metering (Auto & OBD-II)](https://faultcodes.org/automotive/fuel-trim-air-o2-metering): 72 codes - [EVAP Emissions Control (Auto & OBD-II)](https://faultcodes.org/automotive/evap-emissions-control): 54 codes - [Catalytic & Exhaust Emissions (Auto & OBD-II)](https://faultcodes.org/automotive/catalytic-exhaust-emissions): 34 codes - [Engine Cooling & Thermostat (Auto & OBD-II)](https://faultcodes.org/automotive/engine-cooling-thermostat): 34 codes - [Drain Pump & Filter (Appliances)](https://faultcodes.org/appliances/drain-pump-filter): 3 codes - [Gas Ignition & Flame Sensing (HVAC & Boilers)](https://faultcodes.org/hvac/gas-ignition-flame-sensing): 3 codes - [Overheat Protection & Circulation (HVAC & Boilers)](https://faultcodes.org/hvac/overheat-protection-circulation): 3 codes - [Air Pressure Switch & Flue (HVAC & Boilers)](https://faultcodes.org/hvac/air-pressure-switch-flue): 2 codes - [Boiler Water Pressure (HVAC & Boilers)](https://faultcodes.org/hvac/boiler-water-pressure): 2 codes - [AquaStop Base Pan Sensor (Appliances)](https://faultcodes.org/appliances/aquastop-base-pan-sensor): 1 codes - [Burner Ionization & Gas Valve (HVAC & Boilers)](https://faultcodes.org/hvac/burner-ionization-gas-valve): 1 codes - [Direct Drive Motor & Hall Sensor (Appliances)](https://faultcodes.org/appliances/direct-drive-motor-hall-sensor): 1 codes - [Dishwasher Drain Hose (Appliances)](https://faultcodes.org/appliances/dishwasher-drain-hose): 1 codes - [Dishwasher Heating Pump (Appliances)](https://faultcodes.org/appliances/dishwasher-heating-pump): 1 codes ## Top Flagship Diagnostic Guides (HTML + Clean Markdown) - [Vaillant F.28 — Vaillant Boiler Fault Code F.28: Ignition Failure Lockout](https://faultcodes.org/hvac/vaillant-f28) ([Markdown](https://faultcodes.org/api/codes/vaillant-f28/markdown)): Vaillant ecoTEC / atmoTEC failed to detect an ionization flame signal after 3 consecutive ignition attempts—caused by interrupted gas supply, empty prepayment credit, frozen condensate pipes, fouled/worn electrodes, air/flue blockage, or gas valve/PCB faults. - [OBD-II P0420 — Catalyst System Efficiency Below Threshold (Bank 1)](https://faultcodes.org/automotive/obd2-p0420) ([Markdown](https://faultcodes.org/api/codes/obd2-p0420/markdown)): The Bank 1 catalytic converter fell below oxygen-storage or thermal efficiency thresholds compared with upstream sensor readings—caused by catalyst aging, oil/misfire poisoning, exhaust leaks ahead of Sensor 2, or skewed O2 sensors. - [Bosch / Siemens E18 — Bosch / Siemens Washing Machine Drain Error E18 (F18 / d02)](https://faultcodes.org/appliances/bosch-e18) ([Markdown](https://faultcodes.org/api/codes/bosch-e18/markdown)): Drain pump timeout triggered after failing to empty the drum cleanly—officially traced to a clogged front-bottom coin-trap pump filter, jammed pump impeller, kinked rear drain hose, or unremoved sink-siphon knockout plug. - [OBD-II P0300 — Random / Multiple Cylinder Misfire Detected](https://faultcodes.org/automotive/obd2-p0300) ([Markdown](https://faultcodes.org/api/codes/obd2-p0300/markdown)): Crankshaft speed monitoring detected engine misfires across multiple cylinders (or changing randomly)—triggering a solid Check Engine light at ~1–2%+ emissions rate and a FLASHING warning light at >= 5% catalyst-damaging misfire rate. - [Bosch / Siemens E15 — Bosch / Siemens Dishwasher E15 Error (AquaStop Base Flood Triggered)](https://faultcodes.org/appliances/bosch-e15) ([Markdown](https://faultcodes.org/api/codes/bosch-e15/markdown)): Water accumulated in the bottom base tray and lifted the AquaStop styrofoam float switch—locking out wash cycles with the water-tap icon until dried, most commonly resolved by installing BSH Sump Seal Repair Kit #12005744. - [OBD-II P0171 — System Too Lean (Bank 1)](https://faultcodes.org/automotive/obd2-p0171) ([Markdown](https://faultcodes.org/api/codes/obd2-p0171/markdown)): Long-Term Fuel Trim on Bank 1 hit its upper enrichment limit (+25% to +36%) because excess unmeasured air entered combustion or fuel delivery fell short—commonly caused by split PCV/vacuum hoses, dirty MAF sensors, or weak fuel pumps. - [Vaillant F.22 — Vaillant Boiler Fault Code F.22: Low System Water Pressure / Dry Fire](https://faultcodes.org/hvac/vaillant-f22) ([Markdown](https://faultcodes.org/api/codes/vaillant-f22/markdown)): Central heating water pressure dropped below Vaillant's safe minimum (~< 1.0 bar cold, locking out around 0.3–0.5 bar)—fixed cleanly by repressurising via the filling loop to 1.0–1.5 bar cold unless leaks or expansion vessel wear cause recurring drops. - [Windows 0x80070005 — Windows Error Code 0x80070005 (E_ACCESSDENIED)](https://faultcodes.org/software/windows-0x80070005) ([Markdown](https://faultcodes.org/api/codes/windows-0x80070005/markdown)): Windows Update, Microsoft Store, OneDrive folder backup, activation, or an installer hit E_ACCESSDENIED—blocking access to required system files, registry hives, or DCOM permissions (SELF). - [Worcester Bosch EA — Worcester Bosch Greenstar EA Fault Code (Flame Detection / Ignition Lockout)](https://faultcodes.org/hvac/worcester-bosch-ea) ([Markdown](https://faultcodes.org/api/codes/worcester-bosch-ea/markdown)): Flame was not detected or failed to stabilize during Worcester Bosch Greenstar ignition—fixed safely via checking household gas supply, thawing frozen exterior plastic condensate pipes, and holding the blue Reset button ~3 seconds (once or twice max). - [LG OE — LG Washing Machine Drain Error (OE — Outlet Error)](https://faultcodes.org/appliances/lg-oe) ([Markdown](https://faultcodes.org/api/codes/lg-oe/markdown)): LG washer 'Outlet Error' triggered after failing to drain tub water within the ~10-minute cycle window—officially traced to clogged bottom-left coin traps, jammed pump impellers, rear hose kinks (<4 in wall clearance), or household plumbing clogs. - [OBD-II P0128 — Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)](https://faultcodes.org/automotive/obd2-p0128) ([Markdown](https://faultcodes.org/api/codes/obd2-p0128/markdown)): Engine coolant took too long to reach regulating temperature after a cold start—such as falling below ~65 °C on GM heat models or <78 °C on Ford 89 °C thermostats—overwhelmingly caused by a stuck-open thermostat. - [Viessmann F4 — Viessmann Vitodens Fault Code F4: Burner Ignition / Flame Signal Error](https://faultcodes.org/hvac/viessmann-f4) ([Markdown](https://faultcodes.org/api/codes/viessmann-f4/markdown)): Viessmann Vitodens gas boiler failed to establish or sustain a flame signal during ignition—officially attributed to dirty/worn ionization & ignition electrodes, gas supply interruption, frozen exterior condensate drains, flue blockages, or gas valve/PCB failure. - [Windows IRQL_NOT_LESS_OR_EQUAL — Windows Blue Screen Stop Code IRQL_NOT_LESS_OR_EQUAL (0x0000000A)](https://faultcodes.org/software/windows-irql-not-less-or-equal) ([Markdown](https://faultcodes.org/api/codes/windows-irql-not-less-or-equal/markdown)): Bug Check 0xA: Windows or a kernel-mode driver attempted to access pageable or invalid memory at a raised Interrupt Request Level (IRQL >= DISPATCH_LEVEL)—commonly traced to faulty drivers, corrupted pointers, RAM instability, or CPU undervolts. - [Windows MEMORY_MANAGEMENT — Windows Blue Screen Stop Code MEMORY_MANAGEMENT (0x0000001A)](https://faultcodes.org/software/windows-memory-management) ([Markdown](https://faultcodes.org/api/codes/windows-memory-management/markdown)): Bug Check 0x1A: Windows detected severe memory-management corruption (page tables, PFN lists, or pool corruption)—per Microsoft Learn frequently pointing to defective/unstable physical RAM, XMP/EXPO instability, or failing SSD pagefile storage. - [OBD-II P0442 — Evaporative Emission (EVAP) System Small Leak Detected (0.040" / 1 mm)](https://faultcodes.org/automotive/obd2-p0442) ([Markdown](https://faultcodes.org/api/codes/obd2-p0442/markdown)): Fuel vapor containment failed a ~0.040 in (1 mm) / 0.020 in pressure-decay leak test—most commonly caused by a loose or cracked rubber gas cap gasket, split EVAP purge hose, or leaking canister vent seal. - [LG UE — LG Washing Machine Unbalanced Load Error (UE / uE)](https://faultcodes.org/appliances/lg-ue) ([Markdown](https://faultcodes.org/api/codes/lg-ue/markdown)): LG detected uneven drum weight distribution or machine cabinet wobble before high-speed spinning (uE auto-balancing vs UE cycle stop)—solved by redistributing ~2/3 drum loads, tightening leveling feet lock nuts, or inspecting worn shock absorbers. - [Windows 0x80070643 — Windows Update Error 0x80070643 (ERROR_INSTALL_FAILURE / KB5034441)](https://faultcodes.org/software/windows-0x80070643) ([Markdown](https://faultcodes.org/api/codes/windows-0x80070643/markdown)): Installation aborted with ERROR_INSTALL_FAILURE (MSI 1603)—most notoriously when installing Windows Recovery Environment (WinRE) update KB5034441 on Windows 10/11 partitions lacking >= 250 MB of free recovery space, or when .NET/MSI servicing locks fail. - [Samsung 4E — Samsung Washing Machine Water Supply Error (4E / 4C)](https://faultcodes.org/appliances/samsung-4e) ([Markdown](https://faultcodes.org/api/codes/samsung-4e/markdown)): Washer failed to reach target water level within the fill timeout—most commonly solved by opening both supply taps fully, scrubbing clogged inlet hose mesh filters (recommended twice yearly), avoiding 'Flood Safe' hoses, or replacing the water inlet valve. - [PlayStation 5 CE-108262-9 — PS5 Error CE-108262-9: System Software or Application Data Read Failure](https://faultcodes.org/software/ps5-ce-108262-9) ([Markdown](https://faultcodes.org/api/codes/ps5-ce-108262-9/markdown)): Official PlayStation error indicating corrupted PS5 system software, game cache, or external USB storage—resolve via Safe Mode Option 5 (Clear Cache & Rebuild Database) or firmware update/reinstall. - [Windows CRITICAL_PROCESS_DIED — Windows CRITICAL_PROCESS_DIED (0x000000EF): Critical OS Process Terminated](https://faultcodes.org/software/windows-critical-process-died) ([Markdown](https://faultcodes.org/api/codes/windows-critical-process-died/markdown)): Bug check 0x000000EF occurs when a required Windows kernel/user-mode process (csrss.exe, wininit.exe, services.exe) terminates unexpectedly—repair via DISM/SFC, WinRE offline SFC, NVMe/BIOS updates, or MEMORY.DMP analysis. - [Vaillant F.29 — Vaillant Boiler Fault Code F.29: Flame Extinguished During Running](https://faultcodes.org/hvac/vaillant-f29) ([Markdown](https://faultcodes.org/api/codes/vaillant-f29/markdown)): Burner ignited initially yet lost its flame signal mid-operation—most commonly triggered by a frozen or algae-blocked exterior condensate drain backing wastewater up into the trap/sump, flue gas recirculation, gas pressure dips, or worn ionization probes. - [Miele F11 — Miele Dishwasher Water Drainage Error (F11)](https://faultcodes.org/appliances/miele-f11) ([Markdown](https://faultcodes.org/api/codes/miele-f11/markdown)): Dishwasher failed to drain sump water within timeout—most famously solved per Miele guidelines by clearing the triple-filter combo, lifting the non-return check valve to free glass/debris from the pump impeller, and snapping the check valve vertically straight back in. - [LG LE — LG Washer Error LE: Locked Motor / Rotor Position Sensor Fault](https://faultcodes.org/appliances/lg-le) ([Markdown](https://faultcodes.org/api/codes/lg-le/markdown)): Main PCB failed to detect expected drum rotation from the Hall Rotor Position Sensor (RPS)—test stator phase coils (5–15 Ω), Hall sensor pins (5–15 kΩ), and clear overload or suds lock. - [OBD-II P0455 — Evaporative Emission (EVAP) System Large Leak Detected](https://faultcodes.org/automotive/obd2-p0455) ([Markdown](https://faultcodes.org/api/codes/obd2-p0455/markdown)): Zero tank vacuum built up during the EVAP pull-down test—such as failing to reach ~-2 kPa in 30 s (Ford) or 2,740 Pa after 20 L purge (GM)—usually caused by a missing/loose gas cap, popped EVAP hose, stuck-open vent valve, or stuck-closed purge solenoid. - [Daikin U4 — Daikin AC & Heat Pump Error Code U4: Indoor-Outdoor Communication Failure](https://faultcodes.org/hvac/daikin-u4) ([Markdown](https://faultcodes.org/api/codes/daikin-u4/markdown)): Data transmission dropped between indoor air handler(s) and outdoor condenser—officially diagnosed via 5-minute full breaker reset, shielded twisted-pair F1/F2 wiring checks (infinite resistance unhooked, 14–18 V DC pulsing nominal), single-end shield grounding, and PCB isolation. - [Xbox 0x800705b4 — Xbox Error 0x800705b4: System Update or Startup Timeout (ERROR_TIMEOUT)](https://faultcodes.org/software/xbox-0x800705b4) ([Markdown](https://faultcodes.org/api/codes/xbox-0x800705b4/markdown)): Official Xbox timeout code (ERROR_TIMEOUT) triggered during OS update or startup—fix via 10 s hard power cycle, Xbox Startup Troubleshooter (PAIR + EJECT 10–15 s), or NTFS ≥ 6 GB USB Offline System Update (OSU1). - [Samsung 5E — Samsung Washer Error 5E / SE / 5C: Water Drain Timeout](https://faultcodes.org/appliances/samsung-5e) ([Markdown](https://faultcodes.org/api/codes/samsung-5e/markdown)): Washer failed to empty the tub within the allowed drain window—clean the lower-front debris filter, inspect pump impeller blades, and verify official 60–90 cm (24–35 in) standpipe hose height. - [PlayStation 5 CE-108255-1 — PlayStation 5 Error Code CE-108255-1 (Application / Game Crash)](https://faultcodes.org/software/ps5-ce-108255-1) ([Markdown](https://faultcodes.org/api/codes/ps5-ce-108255-1/markdown)): Sony's PS5 application crash error ('An error occurred with the game/application')—triggered by corrupted game/system cache, graphics strain (Ray Tracing / 120Hz / VRR), slow USB drives, or faulty PS5 GPU/RAM hardware when occurring across every title. - [Samsung DC — Samsung Washer Error DC / Ub / UE: Unbalanced Load or Door Lock Interlock](https://faultcodes.org/appliances/samsung-dc) ([Markdown](https://faultcodes.org/api/codes/samsung-dc/markdown)): Control board halted spin acceleration after detecting severe drum vibration (DC / Ub / UE) or an unlatched door state (dC)—redistribute tangled laundry, level feet on solid flooring, and run Calibration Mode. - [Bosch / Siemens E09 — Bosch / Siemens Dishwasher E09: Circulation Heat Pump Heater Failure](https://faultcodes.org/appliances/bosch-e09) ([Markdown](https://faultcodes.org/api/codes/bosch-e09/markdown)): BSH dishwashers combine the heating element directly inside the circulation pump—E09 triggers when heater coil resistance falls outside ~20–25 Ω (usually OL open circuit), harness pins melt, or the board heater relay fails. - [Worcester Bosch E9 — Worcester Bosch E9 Fault Code: Central Heating Overheat Safety Limiter (105 °C)](https://faultcodes.org/hvac/worcester-bosch-e9) ([Markdown](https://faultcodes.org/api/codes/worcester-bosch-e9/markdown)): High-limit lockout triggered when the central heating flow Safety Temperature Limiter exceeds 105 °C (often logged with sub-codes 219, 220, 221, or 224)—check cold pressure (1.0–1.5 bar) and open valves, then book a Gas Safe engineer. - [Vaillant F.75 — Vaillant Boiler Fault F.75: No Pressure Jump Detected on Pump Start](https://faultcodes.org/hvac/vaillant-f75) ([Markdown](https://faultcodes.org/api/codes/vaillant-f75/markdown)): Vaillant's PCB demands a dynamic ≥ 0.05 bar (50 mbar) pressure pulse when starting the circulation pump—if static pressure sits below 1.0 bar or the water pressure sensor/pump fails, burner ignition locks out on F.75. - [Viessmann F2 — Viessmann Boiler Fault F2: Overheat Safety Temperature Limiter (STB) Tripped](https://faultcodes.org/hvac/viessmann-f2) ([Markdown](https://faultcodes.org/api/codes/viessmann-f2/markdown)): Burner safety lockout triggered when primary heat-exchanger flow hits ~90–100 °C and trips the hardwired Safety Temperature Limiter (STB)—check 1.0–1.5 bar pressure, radiator flow, or frozen condensate drain; do NOT force repeated resets. - [OBD-II P0301 — Cylinder 1 Misfire Detected](https://faultcodes.org/automotive/obd2-p0301) ([Markdown](https://faultcodes.org/api/codes/obd2-p0301/markdown)): Over 90% of detected crankshaft-speed misfires are occurring specifically on Cylinder 1—commonly solved cleanly via a 5-minute coil/spark plug swap test to isolate a bad Cylinder 1 ignition coil, cracked plug insulator, or clogged injector. - [macOS -36 — macOS Finder Error Code -36: File I/O & AppleDouble (._*) Copy Failure](https://faultcodes.org/software/macos-error-36) ([Markdown](https://faultcodes.org/api/codes/macos-error-36/markdown)): Apple Carbon/POSIX ioErr (-36) occurs when Finder fails reading/writing hidden ._* AppleDouble resource forks or damaged sectors on exFAT/FAT32 drives and SMB shares—fix with Terminal dot_clean, Disk Utility First Aid, or ditto. - [Windows 0x800f0922 — Windows Update Error 0x800f0922: Full System/EFI Partition or CBS Failure](https://faultcodes.org/software/windows-0x800f0922) ([Markdown](https://faultcodes.org/api/codes/windows-0x800f0922/markdown)): Windows Update rollback (CBS_E_INSTALLERS_FAILED) triggered when the System Reserved / EFI partition lacks ≥ 15 MB free space, VPN blocks Microsoft servers, or Servicing/Task Scheduler installers abort. - [Bosch / Siemens E24 — Bosch / Siemens Dishwasher E24: Drain Hose, Siphon or Pump Cover Blocked](https://faultcodes.org/appliances/bosch-e24) ([Markdown](https://faultcodes.org/api/codes/bosch-e24/markdown)): Washer failed to evacuate sump water in time (paired closely with E25)—check kinked hose, under-sink siphon spigot or garbage-disposal knockout plug, and click the white sump drain pump cover firmly locked. - [Vaillant F.20 — Vaillant Boiler Fault F.20: Safety Switch-Off via Temperature Limiter (STB)](https://faultcodes.org/hvac/vaillant-f20) ([Markdown](https://faultcodes.org/api/codes/vaillant-f20/markdown)): Hardwired Safety Temperature Limiter (STB) tripped independently near ~97 °C to stop burner overheat—check cold pressure (1.0–1.5 bar) and open valves, perform one cool reset, and call a certified engineer if F.20 repeats. - [Whirlpool F5 E2 — Whirlpool Washer Error F5 E2: Door / Lid Lock Switch Failure](https://faultcodes.org/appliances/whirlpool-f5-e2) ([Markdown](https://faultcodes.org/api/codes/whirlpool-f5-e2/markdown)): Main control board (CCU/ACU) commanded door lock yet failed to receive closed switch feedback—clear trapped gasket obstructions, power-reset 5 minutes, and test lock solenoid coil (50–1,500 Ω) plus switch continuity (0–5 Ω). - [PlayStation 5 NW-102216-2 — PS5 Error NW-102216-2: PlayStation Network Connection & DNS Timeout](https://faultcodes.org/software/ps5-nw-102216-2) ([Markdown](https://faultcodes.org/api/codes/ps5-nw-102216-2/markdown)): Failed connection handshake with PlayStation Network—verify status.playstation.com, power-cycle router/modem unplugged ≥ 5 minutes, switch DNS to Cloudflare (1.1.1.1) or Google (8.8.8.8), and allow PSN TCP/UDP ports. - [OBD-II P0174 — OBD-II P0174: System Too Lean (Bank 2)](https://faultcodes.org/automotive/obd2-p0174) ([Markdown](https://faultcodes.org/api/codes/obd2-p0174/markdown)): SAE J2012 code set when Long Term Fuel Trim exceeds roughly +20% to +25% trying to keep Bank 2 (opposite cylinder #1) at 14.7:1—compare freeze-frame idle vs 2,500 RPM trims and whether P0171 co-occurs. - [Xbox 0x87e10bc6 — Xbox Error 0x87e10bc6: Game License or Xbox Store Authentication Failed](https://faultcodes.org/software/xbox-0x87e10bc6) ([Markdown](https://faultcodes.org/api/codes/xbox-0x87e10bc6/markdown)): Xbox / Windows failed to verify digital ownership with Microsoft licensing servers—check Xbox Status & Game Pass rotation, hard power-cycle (10 s / 60 s) or set Home Xbox on console, and sync Windows clock + WSReset.exe on PC. - [Buderus 3Y — Buderus Boiler Fault 3Y (215): Air Pressure Switch & Flue Draft Failure](https://faultcodes.org/hvac/buderus-3y) ([Markdown](https://faultcodes.org/api/codes/buderus-3y/markdown)): Burner lockout paired with service code 215 when the differential air pressure switch fails to switch upon fan start—check exterior flue outlet safely, perform one reset, then call a certified SHK/Gas Safe engineer. - [Buderus 6A — Buderus Boiler Fault 6A (227): No Flame Detected / Ionization Failure](https://faultcodes.org/hvac/buderus-6a) ([Markdown](https://faultcodes.org/api/codes/buderus-6a/markdown)): Burner lockout paired with service code 227 after ignition attempts fail to establish stable micro-ampere (µA) ionization current—confirm external gas valves are open, press Reset once, and book a certified heating engineer. - [Daikin A5 — Daikin AC / Heat Pump A5: Freeze-Up Protection or High-Pressure Coil Limit](https://faultcodes.org/hvac/daikin-a5) ([Markdown](https://faultcodes.org/api/codes/daikin-a5/markdown)): Daikin stops the compressor on A5 when indoor heat-exchanger coil drops < 0 °C in Cooling (freeze protection) or rises > 61 °C in Heating (high pressure)—clean dirty air filters first, check fan airflow, and verify coil thermistor / multi-split wiring. - [PlayStation 5 CE-100005-6 — PS5 Error CE-100005-6: Optical Disc Read or Game Load Failure](https://faultcodes.org/software/ps5-ce-100005-6) ([Markdown](https://faultcodes.org/api/codes/ps5-ce-100005-6/markdown)): Official PlayStation error when reading a physical Blu-ray game disc or damaged SSD installation fails—wipe disc from center straight out to edge, confirm vertical label faces left, delete/reinstall, or Rebuild Database in Safe Mode. - [Bosch / Siemens E19 — Bosch / Siemens Dishwasher E19: Heat Exchanger Drain Valve Coil Fault](https://faultcodes.org/appliances/bosch-e19) ([Markdown](https://faultcodes.org/api/codes/bosch-e19/markdown)): BSH dishwashers log E19 when the heat-exchanger outlet valve or dispenser coil fails—ohm-test behind the left side panel (~7.5 kΩ for blue-plug DC valves, ~2.2 kΩ for pink-plug pre-2016 AC valves, or 7.5–11.5 kΩ dispenser coil). - [Miele F20 — Miele Washer / Dishwasher Fault F20: Heating System & NTC Timeout](https://faultcodes.org/appliances/miele-f20) ([Markdown](https://faultcodes.org/api/codes/miele-f20/markdown)): Water failed to reach target temperature before Miele's Thermostop deadline—power off ≥ 2 min to reset capacitors, then ohm-test the NTC sensor (14.9 kΩ at 20 °C / 12.0 kΩ at 25 °F/25 °C), heater (20–50 Ω), chassis insulation, and K1-1 relay. - [Viessmann F5 — Viessmann Boiler Fault F5 (F05): Air Pressure Switch / Flue Draft Error](https://faultcodes.org/hvac/viessmann-f5) ([Markdown](https://faultcodes.org/api/codes/viessmann-f5/markdown)): Combustion safety lockout when the differential air pressure switch fails to open before blower start or close under differential pressure (Pa)—check outside flue outlet safely, try one reset, then call a certified heating engineer. - [Whirlpool F9 E1 — Whirlpool Washer Error F9 E1: Long Drain Timeout (8–10 Minutes)](https://faultcodes.org/appliances/whirlpool-f9-e1) ([Markdown](https://faultcodes.org/api/codes/whirlpool-f9-e1/markdown)): Washer failed to pump water down within Whirlpool's 8–10 minute drain window—clean the coin trap & sump hose, verify standpipe height (30–96 in / max 4.5 in hose depth), and ohm-test the drain pump (14–25 Ω). - [Windows INACCESSIBLE_BOOT_DEVICE — Windows INACCESSIBLE_BOOT_DEVICE (0x0000007B): Storage Controller / BCD Stop](https://faultcodes.org/software/windows-inaccessible-boot-device) ([Markdown](https://faultcodes.org/api/codes/windows-inaccessible-boot-device/markdown)): Bug check 0x0000007B occurs when Windows loses access to its boot SSD during startup—most often fixed in seconds by checking UEFI SATA/Intel VMD vs AHCI/RAID mode, unplugging USB drives, or rebuilding boot records via bcdboot in WinRE. - [OBD-II P0401 — OBD-II P0401: Exhaust Gas Recirculation (EGR) Flow Insufficient Detected](https://faultcodes.org/automotive/obd2-p0401) ([Markdown](https://faultcodes.org/api/codes/obd2-p0401/markdown)): SAE J2012 emissions code set when EGR valve commands fail to produce expected DPFE pressure, MAP/MAF change, or EGR temperature rise—often caused by carbon-clogged intake ports or failing DPFE sensors rather than the valve itself. - [Windows 0x80070002 — Windows Update Error 0x80070002: Missing Staging File (ERROR_FILE_NOT_FOUND)](https://faultcodes.org/software/windows-0x80070002) ([Markdown](https://faultcodes.org/api/codes/windows-0x80070002/markdown)): Win32 ERROR_FILE_NOT_FOUND triggered by corrupted update caches—stop bits, wuauserv & cryptsvc, rename %systemroot%\SoftwareDistribution and catroot2 to .old, restart services, and run DISM + sfc /scannow. - [Buderus H07 — Buderus Boiler Fault H07 (1017): Heating System Water Pressure Too Low](https://faultcodes.org/hvac/buderus-h07) ([Markdown](https://faultcodes.org/api/codes/buderus-h07/markdown)): Blocking/status code H07 (1017) halts firing when cold system water pressure drops under minimum threshold (< 0.8 bar / critical < 0.2 bar)—safely refill via external loop to 1.0–1.5 bar, bleed radiators, or service leaking expansion vessels. - [OBD-II P0135 — OBD-II P0135: O2 Sensor Heater Circuit (Bank 1, Sensor 1)](https://faultcodes.org/automotive/obd2-p0135) ([Markdown](https://faultcodes.org/api/codes/obd2-p0135/markdown)): SAE J2012 heater circuit fault on upstream Bank 1 Sensor 1 oxygen sensor—measure heater pins (2–15 Ω normal; > 100 Ω / OL open, < 0.5 Ω short) and confirm 12 V fuse feed + PCM PWM ground during the 2–5 s cold-start check. - [OBD-II P0430 — OBD-II P0430: Catalyst System Efficiency Below Threshold (Bank 2)](https://faultcodes.org/automotive/obd2-p0430) ([Markdown](https://faultcodes.org/api/codes/obd2-p0430/markdown)): Bank 2 catalytic converter oxygen storage capacity (OSC) monitor failed because downstream B2S2 O2 voltage swings like upstream B2S1 instead of holding steady ~0.6–0.7 V—rule out exhaust leaks, misfires, and fuel trims before replacing the Bank 2 cat. - [OBD-II P0101 — OBD-II P0101: Mass Air Flow (MAF) Sensor Range/Performance](https://faultcodes.org/automotive/obd2-p0101) ([Markdown](https://faultcodes.org/api/codes/obd2-p0101/markdown)): Measured MAF g/s airflow deviates > 20% to 35% from the PCM's RPM/MAP/TPS airflow model for 2–4 s steady-state—check split intake boots, dirty hot-wire elements (clean only with MAF-safe spray), clogged air filters, or sticking PCV valves. - [OBD-II P0302 — OBD-II P0302: Cylinder 2 Misfire Detected](https://faultcodes.org/automotive/obd2-p0302) ([Markdown](https://faultcodes.org/api/codes/obd2-p0302/markdown)): Mode $06 Cylinder 2 misfire counter exceeded threshold—use fast coil-swap + plug-swap isolation (#2 -> #1/#3 to see if code moves to P0301/P0303), check spark gap, injector pulse & compression (~120–180 psi, within 10–15%); STOP immediately if the CEL flashes (catalyst meltdown hazard). - [OBD-II P0303 — OBD-II P0303: Cylinder 3 Misfire Detected](https://faultcodes.org/automotive/obd2-p0303) ([Markdown](https://faultcodes.org/api/codes/obd2-p0303/markdown)): Mode $06 Cylinder 3 misfire monitor triggered—swap Coil #3 -> #1/#2 and Plug #3 -> a separate cylinder to pinpoint coil vs plug vs injector/compression; check oil inside the #3 spark plug well (valve cover gasket) and stop immediately if the CEL flashes. - [OBD-II P0304 — OBD-II P0304: Cylinder 4 Misfire Detected](https://faultcodes.org/automotive/obd2-p0304) ([Markdown](https://faultcodes.org/api/codes/obd2-p0304/markdown)): Mode $06 Cylinder 4 misfire counter exceeded limit—swap Coil #4 -> #1/#2, inspect plug wear/carbon tracking, test injector resistance (~11–16 Ω port injection) + noid light, and check compression/leakdown if #4 stays dead; STOP if the CEL flashes. - [OBD-II P0440 — OBD-II P0440: Evaporative Emission (EVAP) Control System Malfunction](https://faultcodes.org/automotive/obd2-p0440) ([Markdown](https://faultcodes.org/api/codes/obd2-p0440/markdown)): General EVAP self-test fail across purge, vent, or tank sealing—check gas cap O-ring first, then ohm-test purge (18–30 Ω) & vent (20–40 Ω) solenoids, verify FTP sensor baseline (~2.5–3.0 V KOEO cap off), and pinpoint leaks with a low-pressure EVAP smoke test. - [OBD-II P0456 — OBD-II P0456: EVAP System Very Small Leak Detected (0.020 in)](https://faultcodes.org/automotive/obd2-p0456) ([Markdown](https://faultcodes.org/api/codes/obd2-p0456/markdown)): CARB/EPA 0.020-inch (0.5 mm) micro-leak threshold tripped (half the 0.040 in P0442 pinhole)—inspect the gas cap gasket & rusted filler neck lip, check purge valve weep, and pinpoint with a low-pressure EVAP smoke tester (~0.5–1.0 psi). - [OBD-II P0118 — OBD-II P0118: Engine Coolant Temperature (ECT) Circuit High Input](https://faultcodes.org/automotive/obd2-p0118) ([Markdown](https://faultcodes.org/api/codes/obd2-p0118/markdown)): NTC thermistor signal pulled ≥ 4.6 V (open circuit / infinite resistance), defaulting PCM coolant temp to -40 °C (-40 °F)—causes hard cold starts, over-rich fueling & cooling fans locked ON; inspect unplugged/corroded pins and test the ohm curve (~2–3 kΩ @ 20 °C -> ~200–300 Ω @ 90 °C). - [OBD-II P0340 — OBD-II P0340: Camshaft Position Sensor "A" Circuit (Bank 1)](https://faultcodes.org/automotive/obd2-p0340) ([Markdown](https://faultcodes.org/api/codes/obd2-p0340/markdown)): Missing or erratic Bank 1 Intake Camshaft Position (CMP) signal (3-wire 5V/12V Hall-effect square wave or 2-wire VR AC pulse), causing extended cranking, stalling, or no-start—test 5 V / 12 V reference + ground + signal continuity, clean metallic debris off sensor tip, and inspect timing belt/chain slack. - [OBD-II P0507 — OBD-II P0507: Idle Air Control (IAC) System RPM Higher Than Expected](https://faultcodes.org/automotive/obd2-p0507) ([Markdown](https://faultcodes.org/api/codes/obd2-p0507/markdown)): Actual warm idle exceeds target map by > 100–200 RPM continuously (5–10 s) while throttle is closed—check unmetered intake vacuum leaks, carbon-bound Electronic Throttle Body (ETB) / IACV, and run the OEM Idle Air Volume Relearn after cleaning. - [OBD-II P0700 — OBD-II P0700: Transmission Control System (MIL Request)](https://faultcodes.org/automotive/obd2-p0700) ([Markdown](https://faultcodes.org/api/codes/obd2-p0700/markdown)): Informational ECM flag proving the Transmission Control Module (TCM) stored active fault(s)—generic OBD-II scanners only show P0700; use an enhanced/OEM all-module scanner to pull the true TCM root code (P0715, P0730, P0741, solenoid codes) and check ATF level/condition + battery voltage first. - [OBD-II P0011 — OBD-II P0011: "A" Camshaft Position Timing Over-Advanced (Bank 1)](https://faultcodes.org/automotive/obd2-p0011) ([Markdown](https://faultcodes.org/api/codes/obd2-p0011/markdown)): Bank 1 intake camshaft phaser stays over-advanced vs crankshaft target—check engine oil level & sludge condition FIRST, then ohm-test VVT Oil Control Valve (OCV) solenoid (6.0–12.0 Ω @ 20 °C, OL to ground, 12V bench click), clean clogged VVT oil screens, and check for a stretched timing chain. - [OBD-II P0141 — OBD-II P0141: O2 Sensor Heater Circuit (Bank 1, Sensor 2)](https://faultcodes.org/automotive/obd2-p0141) ([Markdown](https://faultcodes.org/api/codes/obd2-p0141/markdown)): Downstream post-cat Bank 1 Sensor 2 heater circuit fault—measure heater pins (2–15 Ω normal, > 100 Ω / OL open, < 0.5 Ω short) and inspect the dedicated heater fuse, road-salt corroded underbody pins, and 12 V feed + PCM PWM ground. - [OBD-II P0325 — OBD-II P0325: Knock Sensor 1 Circuit (Bank 1)](https://faultcodes.org/automotive/obd2-p0325) ([Markdown](https://faultcodes.org/api/codes/obd2-p0325/markdown)): Piezoelectric Bank 1 Knock Sensor (KS1) circuit open/shorted or producing zero detonation voltage—PCM retards ignition timing conservatively (causing sluggish acceleration & lower MPG); check rodent-chewed under-manifold knock harness, verify exact mounting bolt torque, and test resistance / AC mV tap response. - [OBD-II P0446 — OBD-II P0446: EVAP Emission Control System Vent Control Circuit](https://faultcodes.org/automotive/obd2-p0446) ([Markdown](https://faultcodes.org/api/codes/obd2-p0446/markdown)): SAE J2012 emissions fault when the canister vent solenoid sticks closed/open, its 20–40 Ω (up to 50–70 Ω) coil circuit faults, or the charcoal canister fresh-air filter plugs—often causing slow gas-pump click-offs during refueling. - [OBD-II P0102 — OBD-II P0102: Mass or Volume Air Flow (MAF) Sensor "A" Circuit Low Input](https://faultcodes.org/automotive/obd2-p0102) ([Markdown](https://faultcodes.org/api/codes/obd2-p0102/markdown)): SAE J2012 powertrain fault when the MAF signal drops below the hardware floor (< 0.15–0.20 V or near 0.0 g/s)—usually caused by an unplugged connector, blown MAF fuse, open wire/short to ground, or oil-fouled hot-wire element. - [OBD-II P0113 — OBD-II P0113: Intake Air Temperature (IAT) Sensor 1 Circuit High](https://faultcodes.org/automotive/obd2-p0113) ([Markdown](https://faultcodes.org/api/codes/obd2-p0113/markdown)): SAE J2012 fault when an open NTC circuit pulls the IAT line > 4.6–4.85 V, locking PCM air-temp readings at < -40 °C (-40 °F)—extremely common right after an air filter change leaves an integrated MAF/IAT plug unplugged. - [OBD-II P0172 — OBD-II P0172: System Too Rich (Bank 1)](https://faultcodes.org/automotive/obd2-p0172) ([Markdown](https://faultcodes.org/api/codes/obd2-p0172/markdown)): SAE J2012 fuel-trim fault triggered when Bank 1 adaptive Long-Term Fuel Trim (LTFT) drops below -20% to -25%—caused by a stuck-open EVAP purge valve (P0496), leaking fuel injector, oil-fouled MAF over-reporting air, high fuel pressure, or skewed cold ECT sensor. - [OBD-II P0335 — OBD-II P0335: Crankshaft Position (CKP) Sensor "A" Circuit](https://faultcodes.org/automotive/obd2-p0335) ([Markdown](https://faultcodes.org/api/codes/obd2-p0335/markdown)): Critical SAE J2012 powertrain fault—loss of primary CKP RPM/TDC signal leaves the engine cranking with 0 RPM on tachometer/scanner and NO spark or fuel injector pulse; check 5 V / 12 V Hall supply or VR coil (~300–1,500 Ω), oil-soaked crank-pulley wiring, and damaged reluctor teeth. - [OBD-II P0411 — OBD-II P0411: Secondary Air Injection (SAIR) System Incorrect Flow Detected](https://faultcodes.org/automotive/obd2-p0411) ([Markdown](https://faultcodes.org/api/codes/obd2-p0411/markdown)): SAE J2012 cold-start emissions code triggered when the SAIR pump fails to produce an expected lean O2 shift within 2–5 s of activation (or sufficient secondary air pressure)—check SAIR fuse/relay, water-logged electric pump, rusted combi check valves, and cracked vacuum lines. - [OBD-II P2096 — OBD-II P2096: Post Catalyst Fuel Trim System Too Lean (Bank 1)](https://faultcodes.org/automotive/obd2-p2096) ([Markdown](https://faultcodes.org/api/codes/obd2-p2096/markdown)): SAE J2012 trim-bias fault when the downstream post-cat O2 sensor stays biased lean (< 0.45 V / λ > 1.02) over steady cruise integration—most commonly caused by a small exhaust leak between upstream and downstream O2 sensors (flex pipe/flange), a skewed rear O2 sensor, fuel-starved Bank 1, or degraded catalyst oxygen storage. - [OBD-II P0016 — OBD-II P0016: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A)](https://faultcodes.org/automotive/obd2-p0016) ([Markdown](https://faultcodes.org/api/codes/obd2-p0016/markdown)): Critical SAE J2012 mechanical phase-timing fault between the crankshaft and Bank 1 intake camshaft (Sensor A)—STOP driving interference engines aggressively to prevent piston-to-valve collision; verify oil level/sludge & VVT OCV (6–12 Ω) first, then check for a stretched timing chain, jumped timing belt, failed tensioner, or slipped reluctor via dual-channel oscilloscope. - [OBD-II P0193 — OBD-II P0193: Fuel Rail Pressure (FRP) Sensor "A" Circuit High Input](https://faultcodes.org/automotive/obd2-p0193) ([Markdown](https://faultcodes.org/api/codes/obd2-p0193/markdown)): SAE J2012 high-pressure fuel fault when a returnless port or GDI rail sensor clips > 4.8–4.95 V (against the 5.0 V reference), triggering limp-home mode—inspect for open sensor ground, signal short to 5 V, unplugged rail sensor, and compare mechanical vs scan-tool rail pressure (~35–65 psi port / 500–2,500+ psi GDI). - [OBD-II P0496 — OBD-II P0496: EVAP System High Purge Flow (Flow During Non-Purge)](https://faultcodes.org/automotive/obd2-p0496) ([Markdown](https://faultcodes.org/api/codes/obd2-p0496/markdown)): SAE J2012 EVAP fault when the canister purge solenoid sticks physically open, drawing continuous intake vacuum into the fuel tank even when commanded 0% closed—famous for causing hard starts right after filling the gas tank; verify via idle hose suction test and coil check (18–30 Ω). - [OBD-II P0715 — OBD-II P0715: Input/Turbine Shaft Speed Sensor "A" Circuit](https://faultcodes.org/automotive/obd2-p0715) ([Markdown](https://faultcodes.org/api/codes/obd2-p0715/markdown)): SAE J2012 transmission fault when the TCM loses the input/turbine shaft RPM signal, triggering harsh/delayed shifts or 2nd/3rd gear limp mode—inspect ATF level/metal shavings, connector oil wicking, and measure VR coil resistance (~300–1,200 Ω) or Hall-effect 5 V / 12 V reference. - [OBD-II U0100 — OBD-II U0100: Lost Communication With ECM/PCM "A" (CAN Bus Timeout)](https://faultcodes.org/automotive/obd2-u0100) ([Markdown](https://faultcodes.org/api/codes/obd2-u0100/markdown)): Critical SAE J2012 network fault—CAN-H / CAN-L bus nodes lost the ECM/PCM heartbeat; check battery voltage (≥ 12.6 V KOEO) and ECM main fuses/relays FIRST, then (with battery disconnected) measure OBD-II Pin 6 (CAN-H) to Pin 14 (CAN-L) = 60 Ω normal (120 Ω open leg, 0 Ω shorted bus). - [OBD-II C0035 — OBD-II C0035: Left Front Wheel Speed Sensor Circuit (ABS / ESC Fault)](https://faultcodes.org/automotive/obd2-c0035) ([Markdown](https://faultcodes.org/api/codes/obd2-c0035/markdown)): SAE J2012 chassis fault—ABS, ESC & Traction Control lights illuminate and ABS disables while base hydraulic brakes still work cautiously; inspect front-left wheel-well harness flex cracks, rust-jacked air gap / cracked tone ring, loose wheel bearing play, and check 2-wire passive ohms (~800–2,000 Ω) or active live wheel speed parity (0 km/h mismatch). - [OBD-II B0001 — OBD-II B0001: Driver Frontal Stage 1 Deployment Control Circuit (SRS Airbag)](https://faultcodes.org/automotive/obd2-b0001) ([Markdown](https://faultcodes.org/api/codes/obd2-b0001/markdown)): Critical SAE J2012 SRS restraint fault—Airbag warning light stays ON and the driver frontal airbag is DISABLED in a crash; CRITICAL SAFETY RULE: NEVER probe SRS squib/inflator pins with a standard ohmmeter (meter test current can fire the airbag!). Certified techs disconnect 12V negative for ≥ 10–15 min and use an approved ~2.0–2.5 Ω SRS simulator to isolate the clock spring (often with dead horn/steering buttons), yellow SRS connectors, or SRS module. - [OBD-II P0299 — Turbocharger / Supercharger "A" Underboost Condition](https://faultcodes.org/automotive/obd2-p0299) ([Markdown](https://faultcodes.org/api/codes/obd2-p0299/markdown)): Actual boost pressure lagged significantly behind target boost—such as >4 psi (28 kPa) for 5 seconds on Ford EcoBoost or 30–55 kPa below target on GM petrol engines—most commonly caused by boost hose leaks, worn wastegate rods, diverter diaphragms, or winter intercooler icing. - [OBD-II P0441 — OBD-II P0441: Evaporative Emission (EVAP) System Incorrect Purge Flow](https://faultcodes.org/automotive/obd2-p0441) ([Markdown](https://faultcodes.org/api/codes/obd2-p0441/markdown)): SAE J2012 EVAP code triggered when the PCM sees purge flow while commanded closed OR zero vacuum/pressure drop when commanded open—inspect split purge vacuum lines, test purge solenoid (18–30 Ω) & idle suction, check canister vent valve (20–40 Ω), and verify FTP atmospheric voltage (~2.5–3.0 V cap off). - [OBD-II P0175 — OBD-II P0175: System Too Rich (Bank 2)](https://faultcodes.org/automotive/obd2-p0175) ([Markdown](https://faultcodes.org/api/codes/obd2-p0175/markdown)): SAE J2012 code set when Bank 2 adaptive Long Term Fuel Trim drops below -20% to -25% trying to lean out an over-fueled cylinder bank—check whether P0172 co-occurs to isolate global MAF/fuel-pressure/EVAP purge faults vs Bank 2 injectors or O2 bias. - [OBD-II P0014 — OBD-II P0014: "B" Camshaft Position Timing Over-Advanced or System Performance (Bank 1)](https://faultcodes.org/automotive/obd2-p0014) ([Markdown](https://faultcodes.org/api/codes/obd2-p0014/markdown)): Exhaust ("B") camshaft phaser on Bank 1 stayed over-advanced or lagged behind ECM target—check engine oil level, viscosity, and sludge FIRST, ohm-test the exhaust VVT OCV solenoid (6.0–12.0 Ω @ 20 °C), and inspect clogged oil screens or cam phaser lock pins. - [OBD-II P0138 — OBD-II P0138: O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)](https://faultcodes.org/automotive/obd2-p0138) ([Markdown](https://faultcodes.org/api/codes/obd2-p0138/markdown)): Downstream post-catalyst zirconia O2 sensor (B1S2) stays pinned > 0.80–0.90 V continuously—inspect for melted signal wire shorted to 12 V heater power, chronically rich running (P0172), or an internally shorted sensor before swapping parts. - [OBD-II P0133 — OBD-II P0133: O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)](https://faultcodes.org/automotive/obd2-p0133) ([Markdown](https://faultcodes.org/api/codes/obd2-p0133/markdown)): Upstream Bank 1 Sensor 1 (B1S1) cross-count transition across 450 mV exceeds ~100–300 ms—graph live 0.1–0.9 V waveform oscillation and rule out pre-cat exhaust leaks, fuel-trim bias, or silicone/coolant poisoning before replacing B1S1. - [OBD-II P0131 — OBD-II P0131: O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)](https://faultcodes.org/automotive/obd2-p0131) ([Markdown](https://faultcodes.org/api/codes/obd2-p0131/markdown)): Upstream B1S1 O2 signal stayed pinned < 150–200 mV for > 2–5 s in closed loop—use a brief intake fuel-enrichment pulse (> 0.8 V jump proves the sensor works!) to separate severe vacuum/fuel starvation from a shorted ground wire or dead sensor. - [OBD-II P0449 — OBD-II P0449: EVAP System Vent Valve / Solenoid Control Circuit](https://faultcodes.org/automotive/obd2-p0449) ([Markdown](https://faultcodes.org/api/codes/obd2-p0449/markdown)): Pure electrical open or short circuit in the rear charcoal canister vent valve solenoid—frequently triggered by road-salt pigtail corrosion; check the EVAP fuse, verify 20–40 Ω solenoid coil resistance, and test 12 V ignition feed plus ECM ground control. - [OBD-II P0451 — OBD-II P0451: EVAP System Pressure Sensor / Switch Range / Performance](https://faultcodes.org/automotive/obd2-p0451) ([Markdown](https://faultcodes.org/api/codes/obd2-p0451/markdown)): Fuel Tank Pressure (FTP) sensor reads erratically, drifts, or stays stuck off atmospheric baseline—verify KOEO open-cap baseline (~2.5–3.0 V by OEM), 5.0 V reference/ground, plugged canister vent, or corroded top-of-tank FTP plug. - [OBD-II P0562 — OBD-II P0562: System Voltage Low (Battery / Alternator Charging Fault)](https://faultcodes.org/automotive/obd2-p0562) ([Markdown](https://faultcodes.org/api/codes/obd2-p0562/markdown)): ECM battery/ignition supply dropped below ~10.0–11.0 V—measure KOEO resting voltage (~12.6 V) and running load voltage (13.5–14.5 V @ idle & 2,000 RPM); ALWAYS fix P0562 FIRST because sagging voltage triggers false U0100, P2135, and P0016 codes. - [OBD-II P0741 — OBD-II P0741: Torque Converter Clutch (TCC) Circuit Performance / Stuck Off](https://faultcodes.org/automotive/obd2-p0741) ([Markdown](https://faultcodes.org/api/codes/obd2-p0741/markdown)): Torque Converter Clutch fails to mechanically lock at highway cruise—live transmission telemetry shows TCC Slip RPM well above ~0 RPM (typically > 50–200 RPM slip while commanded ON); inspect burnt/low ATF fluid first, then TCC solenoid (~10–25 Ω), worn valve-body bore, or converter clutch lining. - [OBD-II P2135 — OBD-II P2135: Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation](https://faultcodes.org/automotive/obd2-p2135) ([Markdown](https://faultcodes.org/api/codes/obd2-p2135/markdown)): Drive-by-wire Electronic Throttle Body dual TPS tracks diverge (TPS1 ~0.5->4.5 V vs TPS2 ~4.5->0.5 V on 5.0 V ref), triggering instant Reduced Engine Power / Limp Mode—check battery voltage (P0562) and corroded throttle pigtails before replacing the ETB + performing Idle Relearn. - [OBD-II P2138 — OBD-II P2138: Throttle / Accelerator Pedal Position Sensor / Switch "D" / "E" Voltage Correlation](https://faultcodes.org/automotive/obd2-p2138) ([Markdown](https://faultcodes.org/api/codes/obd2-p2138/markdown)): Dual Accelerator Pedal Position (APP) sensors inside the cabin gas pedal disagree across their 5.0 V reference slopes, forcing immediate Limp Mode / dead throttle—check wet floor-mat corrosion at the pedal plug, 5.0 V ref drop, and smooth APP1 / APP2 live sweeps first. - [OBD-II P2195 — OBD-II P2195: O2 Sensor Signal Biased / Stuck Lean (Bank 1 Sensor 1)](https://faultcodes.org/automotive/obd2-p2195) ([Markdown](https://faultcodes.org/api/codes/obd2-p2195/markdown)): Wideband A/F pump current (Ip) or Nernst cell signal on B1S1 remains stuck lean (λ > 1.05–1.10) despite maxed positive STFT enrichment—run a brief fuel-enrichment test to separate massive vacuum/exhaust leaks or low fuel pressure from a dead wideband A/F sensor or open signal wire. - [OBD-II U0101 — OBD-II U0101: Lost Communication With Transmission Control Module (TCM)](https://faultcodes.org/automotive/obd2-u0101) ([Markdown](https://faultcodes.org/api/codes/obd2-u0101/markdown)): ECM/ABS/cluster lost high-speed CAN bus messages from the TCM—verify battery health (12.6 V KOEO / 13.5–14.5 V running) and TCM fuses/grounds FIRST, then with battery negative disconnected measure OBD-II Pin 6 (CAN-H) to Pin 14 (CAN-L) = 60 Ω, inspect fluid-wicked TCM connectors, and test wake-up feed. - [OBD-II P0010 — OBD-II P0010: "A" Camshaft Position Actuator Circuit / Open (Bank 1)](https://faultcodes.org/automotive/obd2-p0010) ([Markdown](https://faultcodes.org/api/codes/obd2-p0010/markdown)): Pure electrical open or short in the Bank 1 intake ("A") VVT Oil Control Valve (OCV) solenoid circuit—ohm-test the unplugged coil (6.0–12.0 Ω @ 20 °C, OL to housing ground), check oil-wicked connectors & 12 V fuse, and confirm PCM PWM ground pulse before replacing the OCV. - [OBD-II P0017 — OBD-II P0017: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor B)](https://faultcodes.org/automotive/obd2-p0017) ([Markdown](https://faultcodes.org/api/codes/obd2-p0017/markdown)): Mechanical timing phase mismatch between crankshaft (CKP) and Bank 1 exhaust ("B") camshaft (CMP)—STOP aggressive driving on interference engines (valve-to-piston risk); check oil level/sludge & exhaust VVT OCV (6–12 Ω) first, then diagnose stretched timing chain, slipped exhaust phaser/tone wheel, or failed tensioner via oscilloscope. ## Policies & Verification - [Editorial Policy](https://faultcodes.org/editorial-policy) - [About](https://faultcodes.org/about) - [Sitemap](https://faultcodes.org/sitemap.xml)