FaultCodes.org
F11MieleDrainage SystemVerified Guide· Updated: Nov 22, 2026

Miele Dishwasher Water Drainage Error (F11)

Dishwasher failed to drain sump water within timeout—most famously solved per Miele guidelines by clearing the triple-filter combo, lifting the non-return check valve to free glass/debris from the pump impeller, and snapping the check valve vertically straight back in.

Quick AnswerModerate — Plan Repair

Miele dishwasher error F11 signals a water drainage fault. Unplug/shut off the breaker and ladle out standing sump water before reaching inside—hidden glass shards often sit around the pump wheel. According to official Miele Support steps, clean the triple-filter assembly first, release the non-return check valve by pressing its catch inward and tilting inward to lift it out, manually rotate the drain pump impeller beneath it to clear seeds/glass, and critically seat the non-return valve vertically from above until it clicks completely straight (a crooked non-return valve is one of the top reasons F11 keeps coming back) ($0–$95 DIY check/valve; $140–$290 Miele service).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Drainage System
Professional Repair
$140 – $290

What This Fault Code Means

At the end of pre-rinse and main wash stages, Miele's drain pump pushes water past a spring-hinged ball non-return valve up the discharge hose. If food grease glues the triple filter shut, a lemon seed/glass shard jams the uncovered impeller beneath the check valve, or someone snaps the check valve back slightly sideways so water backflows, F11 interrupts the wash.

Common Symptoms

  • Dishwasher stops with standing water covering the bottom stainless sump filter grid and beeps F11
  • Gurgling/humming noise near the sump without water moving through the sink trap
  • Repeated F11 directly after cleaning filters if the non-return valve was seated unevenly

Most Likely Root Causes

  • Grease-caked triple-filter combination (coarse filter, micro-filter, and flat fine filter) choking water return
  • Jammed, warped, or improperly seated non-return (check) valve beneath the filter grid
  • Broken glass shard, cherry pit, toothpick, or bone sliver blocking the drain pump impeller blades under the non-return valve
  • Kinked rear drain hose, blocked sink spigot/disposal knockout plug, or burned-out Miele drain pump

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Non-Return Valve Release Step

Located inside dishwasher sump beneath the triple-filter combo

Press catch inward -> tilt inward & lift
Official Re-Installation Alignment

A cocked non-return valve is a top cause of recurring F11 faults

Place vertically straight from above until click
Impeller Test Feel (Power OFF)

Hard stops indicate trapped glass, bones, or toothpicks (use gloves)

Spins smoothly with gentle magnetic steps
Filter Combo Structure

All 3 stages must lock tightly flush onto the sump floor

3-stage (coarse + micro + flat fine filter)

Commonly Affected Models & Service Bulletins

  • Miele G4000 & G5000 Series Dishwashers
  • Miele G6000 & G7000 AutoDos EcoFlex Dishwashers
  • Miele Integrated & Freestanding Dishwashers with removable sump Non-Return Valve

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Switch off the dishwasher, unplug/flip breaker, remove the lower dish rack, unscrew and rinse the triple-filter combo completely clean.
  2. 2Scoop out sump water safely, locate the non-return valve (press catch inward -> tilt inward to pull out), rinse its rubber flap/ball, and check for tears or warping.
  3. 3Wearing cut-resistant gloves (broken glass hazard!), reach gently below the removed check valve to spin the drain pump impeller by finger—it should turn smoothly with slight magnetic steps.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Was the triple filter packed with food grease or was debris wedged in the impeller under the non-return valve?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Cut-resistant gloves (for safely checking glass chips in sump)Cup / sponge & towels to bale standing waterSoft brush & warm soapy water (triple-filter & check valve cleaning)Replacement OEM Miele non-return valve (if rubber flap warped/torn)
  1. 1Disconnect electrical power and scoop out standing sump water with a cup/sponge.
  2. 2Remove and wash the triple-filter assembly (coarse, cylindrical micro, and flat fine screen) in hot soapy water.
  3. 3Release the non-return check valve (press locking catch inward -> tilt inward), wash it clean, carefully clear glass chips/pits from the exposed drain pump impeller blades underneath, and confirm smooth rotation.
  4. 4Crucial Official Re-Install: Lower the non-return valve strictly vertically from straight above until it clicks firmly flat—test that it isn't cocked crooked, re-fit the triple filter tightly, inspect the external sink trap/drain hose for kinks, and test a short Rinse cycle.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0 – $95
Professional Repair (Parts + Labor)$140 – $290

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does Miele F11 often come back right after someone cleans the filter?

Miele warns that the non-return valve must be lowered vertically from straight above until it clicks flush. Setting it in sideways leaves a gap or jams the internal check ball, triggering immediate F11 drainage failures.

Can I feel the drain pump impeller move cleanly by hand?

Yes—after disconnecting power and guarding fingers against glass splinters, spinning the impeller beneath the check valve should feel smooth with gentle magnetic motor detents (step-step-step), never gritty or locked solid.

Related Searches & Questions

Miele dishwasher F11 error fixMiele F11 non-return valve check valve resetMiele F11 clean impeller filterMiele F11 error after cleaning filter

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Appliances →
Miele Dishwasher Water Drainage Error (F11) — Causes, Fixes & Cost | FaultCodes.org