FaultCodes.org
E15Bosch / SiemensAquaStop Base Pan SensorVerified Guide· Updated: Nov 22, 2026

Bosch / Siemens Dishwasher E15 Error (AquaStop Base Flood Triggered)

Water accumulated in the bottom base tray and lifted the AquaStop styrofoam float switch—locking out wash cycles with the water-tap icon until dried, most commonly resolved by installing BSH Sump Seal Repair Kit #12005744.

Quick AnswerHigh — Service Soon

Bosch / Siemens dishwasher error E15 (often flashing alongside the water-tap icon) means the AquaStop flood protection switch tripped because water collected in the bottom drip tray (~2–3 mm is enough to lift the styrofoam float). Shut off the water tap and unplug/flip the breaker immediately—the drain pump keeps running continuously even with the power button off to guard against kitchen flooding. Drying the bottom tray behind the kickplate clears a one-time spill, while recurring E15 leaks are most famously fixed with the official BSH Sump Seal Repair Kit (Part #12005744) after checking your door's E-Number ($0–$35 DIY kit; $140–$310 technician).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
AquaStop Base Pan Sensor
Professional Repair
$140 – $310

What This Fault Code Means

Every BSH dishwasher (Bosch, Siemens, Neff, Gaggenau) integrates a sealed plastic bottom safety tray housing a styrofoam float connected to a microswitch. When detergent oversudsing or a weeping gasket leaks water down into that tray, the float closes the AquaStop switch, locking the water inlet valve shut and running the drain pump non-stop until disconnected and emptied.

Common Symptoms

  • Display flashes E15 and the water-tap / faucet icon immediately upon start or mid-cycle
  • Drain pump hums continuously even when the door is open or the front Power button is pressed off
  • Water fails to fill into the tub because the AquaStop inlet valve stays locked closed

Most Likely Root Causes

  • Flattened or dried rubber gasket between the plastic pump sump and stainless steel tub (solved by BSH Repair Kit 12005744)
  • Accidental detergent oversudsing (regular liquid dish soap instead of dishwasher tabs) pushing foam out the air vent
  • Loose or split internal circulation hose, worn door-bottom gasket, or weeping water inlet valve
  • Loose heater-pump O-ring or clogged drain pump seal dripping into the bottom tray

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Safety Trigger Mechanism

Located inside the sealed bottom pan; closes AquaStop circuit on flood detection

Styrofoam float microswitch (~2–3 mm water)
Official BSH Sump Seal Repair Kit

Seals the plastic pump sump rim against the stainless steel tub floor

Part #12005744 (Gasket + Sump Screws)
Fail-Safe Pump Behavior

Pump continues running even with panel powered off until unplugged / breaker off

Inlet shut + continuous drain pump
Parts Compatibility Lookup

Verify exact appliance E-Nr. on Bosch/Siemens shop before ordering seals

Laser-etched E-Number (inner door lip)

Commonly Affected Models & Service Bulletins

  • Bosch Dishwashers (Serie 4, Serie 6, Serie 8, SMS / SMV / SHX / SHPM stainless-tub models)
  • Siemens Dishwashers (iQ300, iQ500, SN-series utilizing pump-sump gasket #12005744)
  • Neff & Gaggenau BSH-built dishwashers sharing the same AquaStop base tray architecture

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Turn off the cold water supply valve under the sink, unplug the dishwasher (or flip the kitchen breaker), and note your exact E-Number laser-etched along the top inner stainless door edge.
  2. 2Unscrew the lower toe-kick panel (Torx T20) underneath the door, shine a flashlight into the base tray to confirm standing water around the round styrofoam float, and soak it completely dry.
  3. 3Restore power temporarily and run a short Rinse cycle with the kickplate still off while watching beneath the center sump bowl with a flashlight for active drips.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Did standing water soak the base tray right after excess foam/dish soap or heavy kitchen spills?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Torx T20 screwdriver (toe-kick & sump fasteners)Absorbent towels / sponge or wet-dry vacuumBSH Sump Seal Repair Kit #12005744 (for active sump-rim leaks)Inspection flashlight
  1. 1Disconnect power at the breaker/plug and turn off the kitchen supply valve before opening lower panels or tilting the appliance.
  2. 2Remove the lower toe-kick plate (Torx T20), carefully blot ALL standing water out of the bottom tray with a towel or sponge until the styrofoam float drops completely dry.
  3. 3If oversudsing caused a one-time leak, dry the tray, use proper low-suds dishwasher tablets, and test a normal cycle.
  4. 4If active water drips from around the central sump rim inside the tray, order Official BSH Sump Seal Repair Kit #12005744 (verify against your E-Number), remove lower racks/filters inside the tub, unfasten the sump screws (Torx T20), clean mineral residue off the stainless tub edge, fit the silicone gasket + tension screws, and leak-test with the kickplate off.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0 – $35
Professional Repair (Parts + Labor)$140 – $310

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

What is Bosch Part Number 12005744 for E15?

BSH Part #12005744 is the official Bosch/Siemens/Neff Sump Seal (Pump Pot) Repair Kit containing a heavy-duty silicone compression gasket and replacement screws designed specifically to stop recurring E15 sump-seam leaks without replacing the entire pump housing. Always match your door's E-Number before ordering.

Why won't my Bosch dishwasher stop humming even when I press Power Off during E15?

The AquaStop styrofoam float switch hard-wires power directly to the drain pump as a flood safeguard so trapped water keeps pumping out. You must unplug it or switch off the circuit breaker while drying the base.

Related Searches & Questions

bosch e15 errorbosch e15 error codebosch e15bosch e15 watertapbosch e15 error code dishwasherbosch e15 error dishwasherbosch e15 error watertapbosch e15 error pump keeps runningbosch e15 codebosch e15 dishwasherbosch e 15 meaningbosch dishwasher e15 meaning

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Appliances →
Bosch / Siemens Dishwasher E15 Error (AquaStop Base Flood Triggered) | FaultCodes.org