# Bosch / Siemens E15: Bosch / Siemens Dishwasher E15 Error (AquaStop Base Flood Triggered)

> **Quick Answer:** Bosch / Siemens dishwasher error E15 (often flashing alongside the water-tap icon) means the **AquaStop flood protection switch** tripped because water collected in the bottom drip tray (`~2–3 mm` is enough to lift the styrofoam float). Shut off the water tap and unplug/flip the breaker immediately—the drain pump keeps running continuously even with the power button off to guard against kitchen flooding. Drying the bottom tray behind the kickplate clears a one-time spill, while recurring E15 leaks are most famously fixed with the official **BSH Sump Seal Repair Kit (Part #12005744)** after checking your door's **E-Number** ($0–$35 DIY kit; $140–$310 technician).

- **URL:** https://faultcodes.org/appliances/bosch-e15
- **Category:** Home Appliances
- **Brand / Standard:** Bosch / Siemens
- **System Area:** AquaStop Base Pan Sensor
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Every BSH dishwasher (Bosch, Siemens, Neff, Gaggenau) integrates a sealed plastic bottom safety tray housing a styrofoam float connected to a microswitch. When detergent oversudsing or a weeping gasket leaks water down into that tray, the float closes the AquaStop switch, locking the water inlet valve shut and running the drain pump non-stop until disconnected and emptied.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Safety Trigger Mechanism | Styrofoam float microswitch (~2–3 mm water) | Located inside the sealed bottom pan; closes AquaStop circuit on flood detection |
| Official BSH Sump Seal Repair Kit | Part #12005744 (Gasket + Sump Screws) | Seals the plastic pump sump rim against the stainless steel tub floor |
| Fail-Safe Pump Behavior | Inlet shut + continuous drain pump | Pump continues running even with panel powered off until unplugged / breaker off |
| Parts Compatibility Lookup | Laser-etched E-Number (inner door lip) | Verify exact appliance E-Nr. on Bosch/Siemens shop before ordering seals |

## Commonly Affected Models & Service Bulletins
- Bosch Dishwashers (Serie 4, Serie 6, Serie 8, SMS / SMV / SHX / SHPM stainless-tub models)
- Siemens Dishwashers (iQ300, iQ500, SN-series utilizing pump-sump gasket #12005744)
- Neff & Gaggenau BSH-built dishwashers sharing the same AquaStop base tray architecture

## Common Symptoms
- Display flashes `E15` and the water-tap / faucet icon immediately upon start or mid-cycle
- Drain pump hums continuously even when the door is open or the front Power button is pressed off
- Water fails to fill into the tub because the AquaStop inlet valve stays locked closed

## Most Likely Root Causes
- Flattened or dried rubber gasket between the **plastic pump sump and stainless steel tub** (solved by BSH Repair Kit `12005744`)
- Accidental detergent oversudsing (regular liquid dish soap instead of dishwasher tabs) pushing foam out the air vent
- Loose or split internal circulation hose, worn door-bottom gasket, or weeping water inlet valve
- Loose heater-pump O-ring or clogged drain pump seal dripping into the bottom tray

## Tools & Parts Reference
- Torx T20 screwdriver (toe-kick & sump fasteners)
- Absorbent towels / sponge or wet-dry vacuum
- BSH Sump Seal Repair Kit #12005744 (for active sump-rim leaks)
- Inspection flashlight

## Step-by-Step Troubleshooting & Fix
1. Disconnect power at the breaker/plug and turn off the kitchen supply valve before opening lower panels or tilting the appliance.
2. Remove the lower toe-kick plate (`Torx T20`), carefully blot ALL standing water out of the bottom tray with a towel or sponge until the styrofoam float drops completely dry.
3. If oversudsing caused a one-time leak, dry the tray, use proper low-suds dishwasher tablets, and test a normal cycle.
4. If active water drips from around the central sump rim inside the tray, order **Official BSH Sump Seal Repair Kit #12005744** (verify against your E-Number), remove lower racks/filters inside the tub, unfasten the sump screws (`Torx T20`), clean mineral residue off the stainless tub edge, fit the silicone gasket + tension screws, and leak-test with the kickplate off.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$35 | $140–$310 |
| GBP | £0–£28 | £110–£240 |
| CAD | CA$0–CA$45 | CA$180–CA$395 |
| EUR | €0–€30 | €120–€270 |
| CHF | CHF 0–CHF 38 | CHF 165–CHF 350 |

## Frequently Asked Questions
### What is Bosch Part Number 12005744 for E15?
BSH Part **#12005744** is the official Bosch/Siemens/Neff Sump Seal (Pump Pot) Repair Kit containing a heavy-duty silicone compression gasket and replacement screws designed specifically to stop recurring E15 sump-seam leaks without replacing the entire pump housing. Always match your door's **E-Number** before ordering.

### Why won't my Bosch dishwasher stop humming even when I press Power Off during E15?
The AquaStop styrofoam float switch hard-wires power directly to the drain pump as a flood safeguard so trapped water keeps pumping out. You must unplug it or switch off the circuit breaker while drying the base.


## Verified Official & Engineering References
- [Bosch Official Support & Owner Manuals (E-Nr Lookup)](https://www.bosch-home.com/us/owner-support/get-support/owner-manuals) (Official Support)
- [Bosch Official Spare Parts & Repair Kit Lookup](https://www.bosch-home.com/us/shop) (Technical Manual)
