FaultCodes.org
E24Bosch / SiemensDishwasher Drain HoseVerified Guide· Updated: Nov 22, 2026

Bosch / Siemens Dishwasher E24: Drain Hose, Siphon or Pump Cover Blocked

Washer failed to evacuate sump water in time (paired closely with E25)—check kinked hose, under-sink siphon spigot or garbage-disposal knockout plug, and click the white sump drain pump cover firmly locked.

Quick AnswerModerate — Plan Repair

Code E24 on Bosch, Siemens, Neff, and Gaggenau dishwashers signals a drainage flow restriction (closely related to E25 jammed impeller). After switching off power and removing lower sump standing water, check three places: verify the sink siphon / garbage disposal knockout plug was removed and isn't clogged with grease, straighten any kinked corrugated drain hose behind the unit, and clean the triple filter plus click the white drain pump cover tightly into place until it snaps—a loose cover drops suction and immediately re-triggers E24. Clearing a pump cover, hose, or siphon costs $0; replacing a failed drain pump runs ~$35–$75 DIY ($120–$260 technician).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Dishwasher Drain Hose
Professional Repair
$120 – $260

What This Fault Code Means

Before refilling or ending cycles, BSH dishwashers sense drain load through current draw on the heat/circulation pump and drain pump. If backpressure from a clogged sink spigot, pinched rear hose, garbage-disposal plug on new installs, or air bypass around an unlatched sump pump cover slows evacuation, the PCB halts with E24 within minutes.

Common Symptoms

  • Dishwasher stops early or near cycle end displaying E24 with murky standing water in the bottom sump
  • Draining sound runs sluggishly or makes a sucking noise because the pump cover isn't snapped down flush
  • E24 appears immediately on the very first run of a newly installed dishwasher

Most Likely Root Causes

  • Loose or unlatched white drain pump cover inside the sump letting pump pressure bypass cleanly
  • Clogged under-sink siphon spigot (grease plug) or unremoved garbage disposal knockout plug on fresh installations
  • Pinched, sharply bent, or collapsed corrugated drain hose behind the cabinet
  • Debris (E25 overlap: glass chips, olive/lemon seeds, labels) blocking pump impeller or failing drain pump motor

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Sump Pump Cover Requirement

Loose volute cover prevents pressure buildup and causes immediate E24

Audible snap-lock seal
Program Drain Reset Hold

Forces 1-minute pump-out test after sump/siphon service

Reset / Cancel held 3 s (`0:01`)
Companion Impeller Jam Code

Both E24 & E25 share pump cavity, check valve, and siphon troubleshooting

E25 (blocked impeller / missing cover)

Commonly Affected Models & Service Bulletins

  • Bosch Serie 2 / Serie 4 / Serie 6 / Serie 8 Dishwashers (SMS / SMV / SMI / SHE / SHX)
  • Siemens iQ100 / iQ300 / iQ500 / iQ700 Dishwashers (SN / SX Series)
  • Neff & Gaggenau BSH-Group Dishwashers

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Switch off AC power at the breaker/outlet, bail hot standing water out of the lower tub, put on cut-resistant gloves, and twist out the cylindrical micro-filter and flat filter plate.
  2. 2Unsnap the plastic drain pump cover inside the sump (pull tab up/back), inspect the pump impeller blades carefully for glass/seeds, and snap the cover back in firmly until it audibly clicks lock-flush.
  3. 3Inspect the rear corrugated drain hose for kinks and detach its end from the sink siphon spigot or garbage disposal to check for grease plugs or a sealed factory knockout disc.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Was the white plastic drain pump cover loose inside the sump, or was grease/debris blocking the sink siphon spigot?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Cut-resistant gloves & sponge/towels (safe sump glass/water removal)Flathead screwdriver / nut driver (hose clamp & sink siphon cleaning)Multimeter (only needed if testing pump windings after plumbing clears)
  1. 1Turn off mains power, wear gloves (in case glass fragments rest in the sump), clean the cylinder/flat mesh filters, lift off the drain pump cover, spin out any pits/shards blocking the impeller, and lock the pump cover securely until it clicks.
  2. 2Straighten kinks along the corrugated drain hose behind the dishwasher and pull off its clamped connection at the sink siphon / disposal inlet.
  3. 3Poke out grease buildup inside the sink trap branch—or knock out and retrieve the solid plastic disposal inlet plug if recently installed—then clamp the drain hose firmly onto the spigot.
  4. 4Restore power, hold Reset / Cancel (3 s) until 0:01 drains any remaining sump water, and verify a Quick Wash completes with zero E24 alert (replace the drain pump only if impeller path and plumbing are spotless yet pump won't spin).

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0 – $75
Professional Repair (Parts + Labor)$120 – $260

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does an unlocked drain pump cover trigger Bosch E24 even when everything is clean?

BSH specifies that the snap-in pump cover forms the volute seal over the impeller. If left slightly tilted or unclicked after cleaning the filter, water simply swirls inside the sump instead of building head pressure up the drain hose, tripping E24.

How do I reset Bosch error E24 once the clog is cleared?

Press and hold the Reset / Start (3 sec) button until the display changes to 0:01, close the door so the 1-minute drain cycle completes, then restart your program.

Related Searches & Questions

Bosch dishwasher E24 fix siphon pump coverSiemens E24 E25 not draining resetBosch E24 new install knockout plugBosch dishwasher reset 0:01 drain

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Appliances →
Bosch / Siemens Dishwasher E24: Drain Hose, Siphon… — Fixes & Cost | FaultCodes.org