FaultCodes.org
E09Bosch / SiemensDishwasher Heating PumpVerified Guide· Updated: Nov 22, 2026

Bosch / Siemens Dishwasher E09: Circulation Heat Pump Heater Failure

BSH dishwashers combine the heating element directly inside the circulation pump—E09 triggers when heater coil resistance falls outside ~20–25 Ω (usually OL open circuit), harness pins melt, or the board heater relay fails.

Quick AnswerModerate — Plan Repair

Code E09 (or E:09 / F09) on Bosch, Siemens, Neff, and Gaggenau dishwashers indicates a water heating circuit fault. On BSH dishwashers built since the late 2000s, the flow-through heater is molded inside the circulation heat pump assembly rather than sold as a standalone tubular element. Test the disconnected pump heater terminals with a multimeter: healthy elements measure ~20–25 Ω (most commonly 20–22 Ω, or ~11 Ω per section on older dual-circuit variants) with infinite (OL) insulation to ground; OL across the heater pins confirms a burned heating trace requiring heat-pump replacement matched to the exact door-frame E-Nr nameplate ($85–$150 DIY; $220–$390 technician).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Dishwasher Heating Pump
Professional Repair
$220 – $390

What This Fault Code Means

During heated wash and final rinse stages, the main power module closes a relay feeding AC power to thick-film heating tracks wrapped around the stainless circulation pump cylinder, monitoring temperature via NTC thermistors. When calcification or dry thermal cycling fractures the heating trace (OL) or burns the control board relay/connector, water stays cold and the controller aborts at cycle end with E09.

Common Symptoms

  • Dishwasher finishes its cycle (or stops late) leaving dishes wet, greasy, and cold with E09 displayed
  • Detergent pod remains partially undissolved in the dispenser or sump because wash water never heated
  • Tripped household breaker/RCD alongside E09 if the heater element insulation shorted to the metal housing

Most Likely Root Causes

  • Burned-out thick-film heating element integrated inside the BSH circulation heat pump (open circuit OL, ~85% of cases)
  • Burnt or cold-soldered heater relay / melted terminal pins on the main power control module
  • Overheated or scorched red power harness plug feeding the heat pump heater connector
  • Ground fault / insulation breakdown inside the flow-through pump heater jacket

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Integrated Heater Nominal Resistance

Older dual-circuit BSH variants read ~11 Ω per coil section

20–25 Ω (typically ~20–22 Ω)
Fault / Burnout Reading

Most frequent cause of E09; indicates fractured thick-film track

OL / ∞ Ω (open circuit)
Chassis Ground Insulation Check

Any continuity to ground leaks current and trips RCD/breaker

OL / ∞ Ω (to pump metal body)
OEM Part Lookup Identifier

Pump connector orientation & hose diameter vary by BSH series

Exact Door-Frame E-Nr + FD

Commonly Affected Models & Service Bulletins

  • Bosch Serie 4 / Serie 6 / Serie 8 Dishwashers (SMV / SMS / SMI / SHX Series)
  • Siemens iQ300 / iQ500 / iQ700 Dishwashers (SN / SX Series)
  • Neff, Constructa & Gaggenau BSH-Platform Flow-Through Heat Pump Dishwashers

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Copy the full E-Nr and FD code engraved on the top inner edge of the stainless steel door—BSH heat pumps vary by exact prefix/suffix revision.
  2. 2Unplug the dishwasher completely (or switch off its circuit breaker), remove the lower kickplate and right-side panel to reach the circulation pump motor, and unplug the heavy heater power connector.
  3. 3Measure resistance across the pump's heater terminals (nominal 20–25 Ω, often ~20–22 Ω; also verify OL / ∞ resistance from each heater pin to chassis ground to rule out insulation leakage).

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

With the heater plug disconnected, does your multimeter read OL (infinite) across the pump heater pins or continuity to ground?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Digital multimeter (Ω resistance + continuity-to-ground check)Torx T20 screwdriver (kickplate & right side panel removal)OEM BSH Circulation Heat Pump matched by E-Nr + stainless hose clampPliers / towels to catch residual sump water
  1. 1Disconnect mains power and turn off the under-sink water valve before tilting or opening the right-hand side panel.
  2. 2Check the heater connector and wiring harness back to the lower-right control module for heat discoloration or loose crimp pins; measure across heater pins (20–25 Ω normal; OL = failed heater trace).
  3. 3If the heater reads OL or shorts to ground, release the sump rubber clamp and install an exact-match OEM BSH circulation heat pump ordered by full E-Nr (fit new single-use ear/screw hose clamps so the sump cannot leak and trip E15).
  4. 4If the pump heater reads cleanly at 20–22 Ω with no ground fault, inspect the lower power PCB for a burnt solder joint or failed heater relay and test heated wash water temperature on a quick hot program.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$85 – $150
Professional Repair (Parts + Labor)$220 – $390

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Can I replace just the heating element instead of the whole Bosch heat pump?

On standard BSH Zeolith/flow-through circulation pumps, official Bosch/Siemens service supplies the sealed heater and pump housing as one complete assembly. Ensure your replacement kit includes a stainless worm-drive or Oetiker clamp matched to the exact E-Nr.

Is it safe to run the dishwasher when E09 appears?

No. Wash water stays cold, detergent won't rinse or sanitize properly, and if an internal heater insulation fault is present it can repeatedly trip your breaker/RCD.

Related Searches & Questions

Bosch dishwasher E09 error code fixSiemens dishwasher E09 heat pump ohmsBosch E09 heating element vs control boardBosch heat pump replacement cost E-Nr

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Appliances →
Bosch / Siemens Dishwasher E09: Circulation Heat Pump Heater Failure | FaultCodes.org