FaultCodes.org
E19Bosch / SiemensHeat Exchanger Drain ValveVerified Guide· Updated: Nov 22, 2026

Bosch / Siemens Dishwasher E19: Heat Exchanger Drain Valve Coil Fault

BSH dishwashers log E19 when the heat-exchanger outlet valve or dispenser coil fails—ohm-test behind the left side panel (~7.5 kΩ for blue-plug DC valves, ~2.2 kΩ for pink-plug pre-2016 AC valves, or 7.5–11.5 kΩ dispenser coil).

Quick AnswerModerate — Plan Repair

Code E19 (or F19) on Bosch, Siemens, Neff, and Gaggenau dishwashers indicates an electrical fault in the heat exchanger drain/outlet valve located at the bottom corner of the flat plastic side reservoir—or less frequently, the detergent dispenser actuator coil. Disconnect AC power, remove the left side panel (Torx T20), unplug the valve coil, and test resistance: modern DC valves (blue connector) measure `~7.5 kΩ` (`7.0–8.0 kΩ`), while older pre-2016 AC valves (pink/red connector) measure `~2.2 kΩ` (0 kΩ or OL confirms coil failure; inspect for plunger rust/water weeping that can blow the lower power PCB triac). Replacing a leaking OEM valve runs ~$25–$65 DIY ($140–$280 service).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Heat Exchanger Drain Valve
Professional Repair
$140 – $280

What This Fault Code Means

Many BSH dishwashers store tempered rinse water inside a flat clear heat exchanger mounted against the left inner wall to pre-warm incoming fill water and aid condensation drying. An electrically driven outlet plunger opens to dump that reservoir into the tub. When hydraulic shaft seals weep into the solenoid coil or a dispenser wax motor/coil shorts (0 kΩ) or burns open (OL), the power PCB halts with E19.

Common Symptoms

  • Dishwasher stops early or mid-program displaying E19 (F19) and beeping repeatedly
  • Water remains trapped inside the clear left-side heat exchanger tank instead of draining into the tub
  • Rust trails or moisture crust visible around the lower plunger tip of the heat exchanger outlet valve

Most Likely Root Causes

  • Open or moisture-shorted heat exchanger drain valve solenoid (OL or 0 kΩ, #1 cause)
  • Water seeping past a calcified valve stem O-ring into the coil windings, swelling/shorting the housing
  • Failed detergent/rinse-aid dispenser actuator coil (~7.5–11.5 kΩ nominal spec out of range)
  • Damaged wire harness or blown triac on the lower main power PCB caused by running a shorted valve

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Newer DC Outlet Valve (Blue Plug)

Tested unplugged at coil terminals behind left cabinet wall

~7.5 kΩ (7.0–8.0 kΩ normal)
Older AC Outlet Valve (Pink/Red Plug)

Verify connector color and E-Nr revision before ordering part

~2.2 kΩ (pre-2016 models)
Dispenser Coil Spec (Secondary Check)

Check front-door soap dispenser actuator if heat-exchanger valve passes

~7.5–11.5 kΩ
Defective Coil Failure Readings

Plunger rust seepage that shorts coil can also damage PCB triac

0 kΩ (short) or OL (open circuit)

Commonly Affected Models & Service Bulletins

  • Bosch Serie 4 / Serie 6 / Serie 8 Dishwashers (SMS / SMV / SMI / SHX Series)
  • Siemens iQ300 / iQ500 / iQ700 Dishwashers (SN / SX Series)
  • Neff, Constructa & Gaggenau BSH-Platform Dishwashers with Side Heat Exchanger

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Disconnect mains power at the outlet/breaker, turn off the water inlet tap, pull the dishwasher out slightly, and unscrew the left side panel (Torx T20 front strip screws + rear clips).
  2. 2Locate the heat exchanger outlet valve clipped into the bottom rear/front pocket of the flat plastic tank, absorb residual drips with a towel before unclipping, and inspect its metal stem for rust streaks or calcium weeping.
  3. 3Measure resistance unplugged across the valve coil pins: expect `7.0–8.0 kΩ` (~`7.5 kΩ`) for newer blue-plug DC valves or `~2.2 kΩ` for older pink/red-plug AC valves; if the valve passes, check the front door detergent dispenser coil (`~7.5–11.5 kΩ`).

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does the unplugged heat-exchanger valve coil read 0 kΩ, OL, or show plunger rust/water leakage outside ~7.5 kΩ (blue DC) / ~2.2 kΩ (pink AC)?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Digital multimeter (kΩ resistance range)Torx T20 screwdriver (left cabinet side panel screws)Absorbent towels & shallow tray (heat exchanger residual water drips)OEM BSH heat exchanger drain valve matched by exact E-Nr
  1. 1Unplug AC power and shut off water supply cleanly before removing the left side cabinet panel.
  2. 2Drain water safely onto towels when releasing the quarter-turn bayonet heat exchanger drain valve, and inspect the rubber seat inside the tank opening for mineral debris.
  3. 3If the coil reads 0 kΩ, OL, or outside 7.0–8.0 kΩ (DC) / ~2.2 kΩ (AC)—or shows rust/swelling—install a brand-new OEM BSH outlet valve matched by door-frame E-Nr and seat its fresh O-ring tightly.
  4. 4If the heat exchanger coil passes resistance, test the door dispenser actuator coil (7.5–11.5 kΩ); if a brand-new OEM valve still throws E19, remove and inspect the lower power PCB for a shorted triac blown by the old valve.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$25 – $65
Professional Repair (Parts + Labor)$140 – $280

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why are there two different resistance values (7.5 kΩ vs 2.2 kΩ) for Bosch E19 valves?

BSH switched from older AC-driven pink/red-plug outlet valves (~2.2 kΩ, pre-2016 builds) to DC-driven blue-plug valves (~7.5 kΩ). Ordering by your exact door-edge E-Nr guarantees the right coil rating and plug keyway.

Why can replacing the Bosch E19 valve alone sometimes fail to clear the error?

When water leaks down the plunger and shorts the coil near 0 Ω, high current can blow the tiny SMD triac on the lower power control module. Always test coil ohms AND check the power board if a new valve triggers E19 immediately.

Related Searches & Questions

Bosch dishwasher E19 error code fixSiemens E19 heat exchanger drain valve ohmsBosch E19 7.5 kOhm vs 2.2 kOhm valveBosch E19 detergent dispenser vs power board

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Appliances →
Bosch / Siemens Dishwasher E19: Heat Exchanger… — Fixes & Cost | FaultCodes.org