# Bosch / Siemens E19: Bosch / Siemens Dishwasher E19: Heat Exchanger Drain Valve Coil Fault

> **Quick Answer:** Code **E19** (or `F19`) on Bosch, Siemens, Neff, and Gaggenau dishwashers indicates an electrical fault in the **heat exchanger drain/outlet valve** located at the bottom corner of the flat plastic side reservoir—or less frequently, the **detergent dispenser actuator coil**. Disconnect AC power, remove the left side panel (`Torx T20`), unplug the valve coil, and test resistance: modern **DC valves (blue connector)** measure **`~7.5 kΩ` (`7.0–8.0 kΩ`)**, while older **pre-2016 AC valves (pink/red connector)** measure **`~2.2 kΩ`** (`0 kΩ` or `OL` confirms coil failure; inspect for plunger rust/water weeping that can blow the lower power PCB triac). Replacing a leaking OEM valve runs ~$25–$65 DIY ($140–$280 service).

- **URL:** https://faultcodes.org/appliances/bosch-e19
- **Category:** Home Appliances
- **Brand / Standard:** Bosch / Siemens
- **System Area:** Heat Exchanger Drain Valve
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Many BSH dishwashers store tempered rinse water inside a flat clear heat exchanger mounted against the left inner wall to pre-warm incoming fill water and aid condensation drying. An electrically driven outlet plunger opens to dump that reservoir into the tub. When hydraulic shaft seals weep into the solenoid coil or a dispenser wax motor/coil shorts (`0 kΩ`) or burns open (`OL`), the power PCB halts with `E19`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Newer DC Outlet Valve (Blue Plug) | ~7.5 kΩ (7.0–8.0 kΩ normal) | Tested unplugged at coil terminals behind left cabinet wall |
| Older AC Outlet Valve (Pink/Red Plug) | ~2.2 kΩ (pre-2016 models) | Verify connector color and E-Nr revision before ordering part |
| Dispenser Coil Spec (Secondary Check) | ~7.5–11.5 kΩ | Check front-door soap dispenser actuator if heat-exchanger valve passes |
| Defective Coil Failure Readings | 0 kΩ (short) or OL (open circuit) | Plunger rust seepage that shorts coil can also damage PCB triac |

## Commonly Affected Models & Service Bulletins
- Bosch Serie 4 / Serie 6 / Serie 8 Dishwashers (SMS / SMV / SMI / SHX Series)
- Siemens iQ300 / iQ500 / iQ700 Dishwashers (SN / SX Series)
- Neff, Constructa & Gaggenau BSH-Platform Dishwashers with Side Heat Exchanger

## Common Symptoms
- Dishwasher stops early or mid-program displaying `E19` (`F19`) and beeping repeatedly
- Water remains trapped inside the clear left-side heat exchanger tank instead of draining into the tub
- Rust trails or moisture crust visible around the lower plunger tip of the heat exchanger outlet valve

## Most Likely Root Causes
- Open or moisture-shorted **heat exchanger drain valve solenoid** (`OL` or `0 kΩ`, #1 cause)
- Water seeping past a calcified valve stem O-ring into the coil windings, swelling/shorting the housing
- Failed **detergent/rinse-aid dispenser actuator coil** (`~7.5–11.5 kΩ` nominal spec out of range)
- Damaged **wire harness or blown triac** on the lower main power PCB caused by running a shorted valve

## Tools & Parts Reference
- Digital multimeter (kΩ resistance range)
- Torx T20 screwdriver (left cabinet side panel screws)
- Absorbent towels & shallow tray (heat exchanger residual water drips)
- OEM BSH heat exchanger drain valve matched by exact E-Nr

## Step-by-Step Troubleshooting & Fix
1. Unplug AC power and shut off water supply cleanly before removing the left side cabinet panel.
2. Drain water safely onto towels when releasing the quarter-turn bayonet **heat exchanger drain valve**, and inspect the rubber seat inside the tank opening for mineral debris.
3. If the coil reads `0 kΩ`, `OL`, or outside `7.0–8.0 kΩ` (DC) / `~2.2 kΩ` (AC)—or shows rust/swelling—install a brand-new **OEM BSH outlet valve** matched by door-frame **E-Nr** and seat its fresh O-ring tightly.
4. If the heat exchanger coil passes resistance, test the door dispenser actuator coil (`7.5–11.5 kΩ`); if a brand-new OEM valve still throws `E19`, remove and inspect the lower power PCB for a shorted triac blown by the old valve.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $25–$65 | $140–$280 |
| GBP | £20–£55 | £110–£220 |
| CAD | CA$35–CA$85 | CA$180–CA$360 |
| EUR | €20–€55 | €125–€250 |
| CHF | CHF 30–CHF 75 | CHF 175–CHF 340 |

## Frequently Asked Questions
### Why are there two different resistance values (7.5 kΩ vs 2.2 kΩ) for Bosch E19 valves?
BSH switched from older AC-driven pink/red-plug outlet valves (`~2.2 kΩ`, pre-2016 builds) to DC-driven blue-plug valves (`~7.5 kΩ`). Ordering by your exact door-edge **E-Nr** guarantees the right coil rating and plug keyway.

### Why can replacing the Bosch E19 valve alone sometimes fail to clear the error?
When water leaks down the plunger and shorts the coil near `0 Ω`, high current can blow the tiny SMD triac on the lower power control module. Always test coil ohms AND check the power board if a new valve triggers `E19` immediately.


## Verified Official & Engineering References
- [Bosch Home Service: Dishwasher E19 Troubleshooting](https://www.bosch-home.com/us/service) (Official Support)
- [Bosch Service Deutschland: Geschirrspüler Fehlercode E19](https://www.bosch-home.com/de/service) (Official Support)
- [Siemens Kundendienst: Wärmetauscher / Ablaufventil E19](https://www.siemens-home.bsh-group.com/de/kundenservice) (Official Support)
