FaultCodes.org
4ESamsungWater Inlet Valve & SupplyVerified Guide· Updated: Nov 22, 2026

Samsung Washing Machine Water Supply Error (4E / 4C)

Washer failed to reach target water level within the fill timeout—most commonly solved by opening both supply taps fully, scrubbing clogged inlet hose mesh filters (recommended twice yearly), avoiding 'Flood Safe' hoses, or replacing the water inlet valve.

Quick AnswerModerate — Plan Repair

Samsung washer error 4E (displayed as `4C` on newer EcoBubble/Smart Care models) means insufficient water entered the drum within the fill timer. Turn the taps off cleanly before inspecting, verify both hot and cold water supply taps are turned fully open (even on cold cycles on dual-inlet units), straighten pinched rear hoses, scrub sand/scale from the inlet valve mesh screens (Samsung recommends cleaning every 6 months), clear detergent dispenser sludge, and remove any aftermarket 'Flood Safe' auto-shutoff hoses—Samsung warns those trigger false 4E/4C faults ($0–$75 DIY mesh clean/valve; $120–$250 technician).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Water Inlet Valve & Supply
Professional Repair
$120 – $250

What This Fault Code Means

When starting a wash or rinse fill, Samsung's control PCB energizes the dual cold/hot solenoid inlet valves and expects the pressure level switch to climb steadily within ~10–15 minutes. If sediment plugs the tiny stainless mesh filters inside the hose ports, a valve coil opens, or water flow trips slow, the washer locks with 4E / 4C.

Common Symptoms

  • Washer flashes 4E or 4C minutes after starting a wash or right before rinse fill
  • Dry laundry inside the drum with barely any water pooling at the bottom, or very loud humming from the back valves
  • Water dribbles slowly through the detergent dispenser tray

Most Likely Root Causes

  • Partially closed water supply faucet (or both hot & cold taps not turned open on dual-inlet North American/global units) or pinched rear inlet hose
  • Rust, sand, or calcium scale clogging the inlet mesh screens inside the rear valve ports (or hose ends)
  • Third-party 'Flood Safe' burst-protection hoses falsely shutting flow off (explicitly flagged by Samsung Support)
  • Clogged detergent dispenser drawer ports or electrically failed water inlet solenoid valve / disconnected pressure sensor hose

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Model Display Equivalents

Identical water-fill timeout error across model years

4E (Classic) / 4C (Newer EcoBubble)
Mesh Screen Maintenance Interval

Located inside both rear inlet ports and hose coupler ends

Clean twice per year (every 6 months)
Samsung Hose Warning

Internal shutoff valves trip falsely under initial fill rush (Samsung Support)

Avoid third-party 'Flood Safe' hoses
Electrical Inlet Valve Spec

Verify coil resistance (~800–1,200 Ω) or active fill voltage when dry

120V / 230V AC supply during fill stage

Commonly Affected Models & Service Bulletins

  • Samsung EcoBubble & AddWash Front-Load Washers (WW60 / WW70 / WW80 / WW90 / WF45 series)
  • Samsung Top-Load High-Efficiency Washers (WA45 / WA50 / WA52 series)
  • Samsung Smart Care Washer-Dryer Combos showing `4C` or `4E`

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Confirm strong house pressure at both faucets into a bucket and make sure NO third-party 'Flood Safe' auto-lock hose is installed.
  2. 2Turn both taps off, unscrew the hoses from the back of the washer, gently extract the small mesh screens with needle-nose pliers, and check for rust/sand blockages.
  3. 3Inspect and flush the pull-out detergent drawer and check if the rear solenoid valves hum or stay dead during a test fill.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Did removing the hoses show sand/scale packed onto the inlet valve mesh filters, OR are 'Flood Safe' hoses installed?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Needle-nose pliers (to extract mesh screens gently)Soft toothbrush (for calcium/rust cleaning)Bucket & towels (before disconnecting water hoses)Multimeter & OEM Water Inlet Valve (if solenoid coils fail)
  1. 1Open both cold and hot supply taps completely and replace any aftermarket 'Flood Safe' hoses with standard braided stainless-steel supply hoses.
  2. 2Turn taps off, disconnect hoses from the rear water ports, gently pull out the mesh filters with needle-nose pliers, brush completely clean under running water with a toothbrush, re-seat filters firmly, and leak-test connections slowly.
  3. 3Pull the detergent dispenser drawer all the way out, scrub hardened soap/fabric softener out of its top spray nozzles and siphon tubes under warm water.
  4. 4If pressure is strong and mesh filters are spotless yet water barely enters while voltage reaches the inlet valve coils (120V/230V AC), unplug power and replace the OEM Water Inlet Valve Assembly.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0 – $75
Professional Repair (Parts + Labor)$120 – $250

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

What is the difference between 4E and 4C on Samsung washers?

They are the exact same water-supply fault code—older Samsung washers display `4E`, while newer EcoBubble and Smart Care models display `4C`.

How often does Samsung recommend cleaning inlet mesh filters?

Samsung Support recommends shutting off the water taps and brushing both inlet mesh screens clean at least twice a year, especially in areas with hard water or municipal pipe sediment.

Related Searches & Questions

Samsung washer 4E 4C error code fixSamsung washer clean mesh filter 4CSamsung 4E flood safe hose problemSamsung water inlet valve replacement cost

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Appliances →
Samsung Washing Machine Water Supply Error (4E / 4C) — Fixes & Cost | FaultCodes.org