FaultCodes.org
E18Bosch / SiemensDrain Pump & FilterVerified Guide· Updated: Nov 22, 2026

Bosch / Siemens Washing Machine Drain Error E18 (F18 / d02)

Drain pump timeout triggered after failing to empty the drum cleanly—officially traced to a clogged front-bottom coin-trap pump filter, jammed pump impeller, kinked rear drain hose, or unremoved sink-siphon knockout plug.

Quick AnswerModerate — Plan Repair

Bosch / Siemens washing machine error E18 (also displayed as F18 or d02 on select series) means the washer timed out trying to pump out water. Turn the dial to Off, unplug the washer, and let hot wash water cool down before draining to prevent scalding. Per official Bosch Support guidelines, empty standing water via the small bottom-front emergency drain hose into a shallow baking tray, unscrew and clean the coin-trap pump filter, verify the pump impeller blades inside turn freely, check the rear hose for kinks or unremoved sink-spigot plugs, then test for leaks by pouring 1 liter (1 quart) of water into the detergent drawer and running Drain/Spin ($0–$65 DIY; $120–$260 technician).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Drain Pump & Filter
Professional Repair
$120 – $260

What This Fault Code Means

Before high-speed spinning begins, the BSH water-level pressure sensor must register an empty tub within the allotted pump cycle time. When coins, hairpins, lint, or detergent buildup block the filter—or the drain hose kinks behind the washer or connects to an obstructed wall/sink trap—the machine halts with E18 and locks the door to keep dirty water off your floor.

Common Symptoms

  • Washer pauses mid-cycle before rinsing or spinning with water trapped behind the glass door
  • Display shows E18 (or F18/d02) with dull pump humming and zero drainage
  • Washer door stays safety-locked while water covers the bottom door gasket

Most Likely Root Causes

  • Clogged bottom-front drain pump filter / coin trap packed with lint, coins, buttons, or small socks (#1 cause)
  • Hairpin, bra wire, or glass sliver wedged behind the filter inside the pump impeller blades
  • Kinked or crushed rear black drain hose, or an unremoved knockout plug inside a newly fitted sink-siphon spigot
  • Clogged pressure chamber hose or electrically burned-out BSH drain pump motor

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Equivalent Display Codes

Code format varies across Serie 4 / 6 / 8 & iQ300 / iQ500 displays

E18 / F18 / d02 (BSH Drain Timeout)
Hot-Water Safety Rule

Prevents scald injury from 60–90 °C wash water before opening drain hose

Turn dial Off, unplug & let cool first
Official Post-Clean Test

Verifies filter gasket seal and full pump evacuation (Bosch Support)

Pour 1 L (1 qt) in drawer -> Drain/Spin
Common Installation Trap

Frequent cause of E18 on newly plumbed washers

Closed blanking plug in sink siphon spigot

Commonly Affected Models & Service Bulletins

  • Bosch Front-Load Washers (Serie 4, Serie 6, Serie 8, WAN / WAT / WAX / WAU)
  • Siemens Front-Load Washers (iQ300, iQ500, iQ700, WM-series sharing `F18`/`E18` error codes)
  • Neff & Constructa BSH-built front-loading washing machines

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Turn the dial to Off, unplug power, and wait for hot cycles to cool safely; open the bottom-front service panel and drain ALL water via the small emergency hose before unscrewing the main filter cap.
  2. 2Unscrew the filter counter-clockwise, remove debris, and reach carefully inside the empty cavity (flashlight!) to spin the impeller wheel cleanly without trapped coins or glass.
  3. 3After tightly screwing the filter shut, test pump seal & flow per official Bosch instructions: pour 1 liter (1 quart) of water into the detergent drawer and run Drain/Spin.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Did draining the emergency hose and removing the coin-trap cap turn up coins, hairpins, lint, or a jammed impeller?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Shallow baking pan / low tray & thick towelsFlashlight (to inspect pump impeller cavity)1-liter measuring jug / bottle (for official Drain/Spin seal test)Soft brush (to clean filter threads & rubber gasket)
  1. 1Turn program knob to Off, unplug the appliance, and let high-temperature wash water cool below scalding risk.
  2. 2Open the bottom-right (or left) service flap, pull the small emergency drain hose forward over a shallow baking dish, pull its cap out to empty the drum slowly, then push the cap firmly back in.
  3. 3Unscrew the circular pump filter counter-clockwise, rinse under warm water, clean the threads + rubber seal ring, ensure the internal impeller wheel rotates freely, and tighten the filter cap firmly clockwise.
  4. 4Inspect the rear black corrugated drain hose for kinks and verify no knockout plug remains inside an under-sink spigot, then pour 1 liter (1 quart) into the dispenser drawer and run Drain/Spin to confirm zero leaks and smooth draining.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0 – $65
Professional Repair (Parts + Labor)$120 – $260

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does Bosch tell you to pour 1 liter of water into the drawer after cleaning the E18 filter?

Pouring ~1 liter (1 quart) into the dispenser drawer wets the internal eco-ball seal and lets you verify right away during Drain/Spin both that the filter rubber gasket doesn't drip on the floor and that the pump clears water cleanly.

How do I open the door when my Bosch washer stops full of water with E18?

Never force the handle! Unplug the machine, let hot water cool, and drain the entire drum slowly through the small emergency hose behind the bottom service panel—once water level drops completely, wait 2–3 minutes for the thermal door lock to release.

Related Searches & Questions

bosch e18 errorbosch e18bosch e18 error codebosch e18 error washing machinebosch e18 washing machinebosch e18 error no blockagebosch e18 codebosch e18 error dishwasherbosch e18 code washing machinebosch e18 hatasıbosch e 18 meaningbosch washing machine e18 meaning

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Appliances →
Bosch / Siemens Washing Machine Drain Error E18 (F18 / d02) | FaultCodes.org