FaultCodes.org
F.22VaillantBoiler Water PressureVerified Guide· Updated: Nov 22, 2026

Vaillant Boiler Fault Code F.22: Low System Water Pressure / Dry Fire

Central heating water pressure dropped below Vaillant's safe minimum (~< 1.0 bar cold, locking out around 0.3–0.5 bar)—fixed cleanly by repressurising via the filling loop to 1.0–1.5 bar cold unless leaks or expansion vessel wear cause recurring drops.

Quick AnswerHigh — Service Soon

Vaillant fault code F.22 (displayed as F22) means central heating water pressure dropped too low (below `1.0 bar` cold, locking out to prevent dry firing as pressure approaches 0.3–0.5 bar). Check for radiator valve drips first, then repressurise slowly using Vaillant's external braided or built-in filling loop valves until the cold display reads `1.0–1.5 bar` (1.2–1.5 bar target), close BOTH filling taps firmly, and press Reset once. If pressure falls right back below 1.0 bar over days/weeks—or spikes past 3.0 bar when hot—have an engineer check a failing expansion vessel, weeping pressure relief valve (PRV), or hidden heating leak ($0 DIY repressurising; $120–$380 vessel recharge/PRV/sensor repair).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Boiler Water Pressure
Professional Repair
$135 – $420

What This Fault Code Means

Vaillant ecoTEC boilers require hydraulic pressure (1.0–1.5 bar when cold) so hot water circulates smoothly across the stainless heat exchanger without boiling into steam pockets (dry firing). When pressure drops near 0.3–0.5 bar—often after radiator bleeding, a tiny radiator valve weep, or a flat expansion vessel diaphragm discharging water out the external copper safety pipe—F.22 halts the burner immediately.

Common Symptoms

  • Display flashes F.22 with cold digital bar reading 0.0–0.6 bar and zero heating or hot water
  • Error occurred shortly after bleeding air from upstairs radiators
  • Pressure cycles from F.22 cold to >3.0 bar with outside copper pipe dripping when hot (flat expansion vessel)

Most Likely Root Causes

  • Recent radiator bleeding reducing closed-loop water volume without topping back up (most common harmless cause)
  • Small weeping radiator lockshield/TRV gland seal or weeping boiler automatic air vent
  • Deflated or ruptured expansion vessel diaphragm forcing excess pressure out the 3 bar safety valve (PRV) when heated
  • Blocked or failed Vaillant water pressure sensor reading false low pressure despite full radiators

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Normal Cold System Pressure

Read on digital display or bottom gauge with heating completely cold

1.0–1.5 bar (target ~1.2–1.5 bar)
Dry-Fire Safety Lockout Zone

Prevents overheating or steam pockets in primary heat exchanger

< 1.0 bar (locks out near ~0.3–0.5 bar)
Hot Overpressure Danger Limit

Swing from F.22 cold to >3 bar hot indicates deflated expansion vessel

>= 2.8–3.0 bar (PRV discharge threshold)
Post-Fill Valve Verification

Prevents continuous over-pressurisation into closed heating circuit

Firmly shut both filling loop valves

Commonly Affected Models & Service Bulletins

  • Vaillant ecoTEC plus & ecoTEC pro Gas Condensing Combi Boilers
  • Vaillant ecoTEC sustain / pure / exclusive Series
  • Vaillant ecoFIT & ecoCOMPACT Heating Units

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read the cold digital display or analog pressure gauge beneath the Vaillant boiler: normal cold pressure sits strictly between `1.0` and `1.5 bar`.
  2. 2Walk past all radiators, towel rails, and exposed valve tails with tissue paper checking for dampness, and inspect the external copper 3 bar safety discharge pipe outdoors for drips.
  3. 3Watch how pressure behaves once topped up to 1.2–1.5 bar when the heating gets fully hot: if it shoots rapidly past 2.5–3.0 bar, the internal expansion vessel has lost its air pre-charge.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Did F.22 appear right after bleeding radiators, with cold bar reading below 1.0 bar?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Built-in Vaillant filling taps or silver braided external filling loop key/hoseTissue paper (to inspect radiator valve tails for slow drips)Engineer pressure pump & calibrated gauge (only if recharging expansion vessel)
  1. 1Ensure heating is cool, locate your Vaillant filling loop underneath the boiler (either two built-in integrated blue/grey taps or an external silver braided hose valve set).
  2. 2Open BOTH filling valves slowly until water hisses gently into the system, watch the cold display climb smoothly to `1.2–1.5 bar` (stay strictly inside 1.0–1.5 bar cold!), and then close BOTH valves firmly.
  3. 3Press the Vaillant Reset button once; bleed trapped radiator air gently if gurgling appears and re-check pressure remains inside 1.0–1.5 bar.
  4. 4If pressure keeps dropping weekly without visible radiator drips—or climbs over 3 bar when warm—book a certified heating engineer to recharge/replace the expansion vessel, clear the water pressure sensor port, or replace a dripping 3 bar PRV.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0
Professional Repair (Parts + Labor)$135 – $420

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

What should the water pressure be on a Vaillant ecoTEC boiler?

Cold operating pressure should sit strictly between `1.0 and 1.5 bar` (1.2–1.5 bar recommended target). Below 1.0 bar risks F.22 lockout (typically triggering around 0.3–0.5 bar), while closing the filling valves tightly prevents climbing past 2.5–3.0 bar hot.

What if I leave the Vaillant filling loop taps open slightly by mistake?

Leaving filling valves open lets cold mains water keep filling the boiler past 3.0 bar, blowing water outside through the safety discharge pipe—always verify both valves sit tightly shut perpendicular/closed afterward.

Related Searches & Questions

vaillant f22 fault codevaillant f22vaillant f22 errorvaillant f22 faultvaillant f22 fault code resetvaillant f22 codevaillant f22 hatasıvaillant f22 resetvaillant f22 fehlervaillant f22 safety switch offvaillant boiler f22 meaningwhat does f 22 mean on a vaillant boiler

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

HVAC & Boilers →
Vaillant Boiler Fault Code F.22: Low System Water… — Fixes & Cost | FaultCodes.org