FaultCodes.org
F.75VaillantPressure Sensor & Circulation PumpVerified Guide· Updated: Nov 22, 2026

Vaillant Boiler Fault F.75: No Pressure Jump Detected on Pump Start

Vaillant's PCB demands a dynamic ≥ 0.05 bar (50 mbar) pressure pulse when starting the circulation pump—if static pressure sits below 1.0 bar or the water pressure sensor/pump fails, burner ignition locks out on F.75.

Quick AnswerHigh — Service Soon

Fault code F.75 on Vaillant ecoTEC boilers means the control board started the internal circulation pump and failed to measure the expected dynamic pressure jump of at least `0.05 bar` (`50 mbar`) within the first seconds before ignition. Check your boiler's cold static system pressure first: if it has dropped below 1.0 bar (or < 0.5 bar), repressurize safely to `1.0–1.5 bar` via the external filling loop and perform one single reset. Never open the boiler combustion casing yourself—if F.75 persists at 1.0–1.5 bar, a Gas Safe / certified heating engineer must clean or replace the choked water pressure sensor, clear air locks, recharge the expansion vessel, or free a seized circulation pump ($150–$560 / £95–£390).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Pressure Sensor & Circulation Pump
Professional Repair
$150 – $560

What This Fault Code Means

To prevent dry-firing an uncirculated heat exchanger, Vaillant software executes a pump pressure-pulse verification on every heat demand. As the circulation impeller accelerates, hydraulic head normally spikes pressure at the sensor by ≥ 0.05 bar (50 mbar). If heating system sludge plugs the tiny brass sensor orifice, the pump rotor seizes, or low static pressure / flat expansion vessel absorbs the pulse, the boiler retries and then locks out on F.75.

Common Symptoms

  • Central heating and domestic hot water stop working with F.75 and an hourglass/fault icon on the Vaillant display
  • Static pressure reads under 1.0 bar—or sits normal (1.2–1.5 bar) yet pump hums faintly without burner lighting
  • Intermittent F.75 lockouts during cold mornings when radiator valves are mostly shut or expansion vessel pressure has decayed

Most Likely Root Causes

  • Sludge, magnetite debris, or scale fouling the electronic water pressure sensor orifice (classic ecoTEC failure)
  • Low cold static system pressure (< 0.5–1.0 bar) or deflated/ruptured expansion vessel damping the pump pulse
  • Seized, air-locked, or failing internal heating circulation pump (including faulty pump capacitor/PWM board)
  • Closed system isolation valves / TRVs eliminating minimum bypass circulation path

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Required Pump-Start Pressure Jump

Measured within first seconds of pump start before burner ignition

≥ 0.05 bar (50 mbar)
Normal Cold Static System Pressure

F.75 commonly triggers once static pressure drops below ~0.5–1.0 bar

1.0–1.5 bar
Internal Boiler Access Rule

Homeowners may only top up external loop & perform single reset

Gas Safe / Certified Engineer Only

Commonly Affected Models & Service Bulletins

  • Vaillant ecoTEC plus & ecoTEC pro Gas Condensing Boilers (VC / VCW Series)
  • Vaillant ecoTEC exclusive & ecoCOMPACT Systems
  • Vaillant atmoTEC / turboTEC Wall-Hung Boilers

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Homeowner safe check only: read cold system pressure on the front display/manometer (must sit around `1.0–1.5 bar`) and verify open heating isolation/radiator bypass flow.
  2. 2If static pressure reads below 1.0 bar, use the external filling loop to bring cold pressure up to 1.0–1.5 bar, bleed radiator air if needed (re-topping pressure), and try one manual reset—do NOT reset repeatedly or open the boiler casing.
  3. 3Certified engineer diagnostics (Gas Safe / registered SHK): measure live D.0 / sensor pressure rise at pump startup against the `≥ 0.05 bar` (`50 mbar`) threshold, check pump shaft torque and winding current, clear/replace the blocked pressure sensor, and test expansion vessel nitrogen/air pre-charge.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is the cold static boiler pressure reading below 1.0 bar on the front gauge/screen?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

External filling loop valve / key (homeowner pressure top-up to 1.0–1.5 bar)Certified engineer: OEM Vaillant Water Pressure Sensor & expansion vessel pump/gaugeCertified engineer: Multimeter, circulation pump tester & magnetite flush kit
  1. 1Verify cold system gauge pressure (1.0–1.5 bar target) and ensure key radiators/auto-bypass flow isn't completely shut off.
  2. 2Top up cold static pressure via the external filling loop if below 1.0 bar, vent radiators if gurgling, re-verify 1.0–1.5 bar, and execute a single reset via the boiler fault-reset button.
  3. 3If F.75 returns with normal static pressure (1.0–1.5 bar), shut down the boiler and book a Gas Safe / certified heating engineer—never remove the sealed appliance front casing yourself.
  4. 4The engineer removes and cleans/replaces the fouled Vaillant water pressure sensor (updating to the revised brass/anti-sludge revision if older), frees or replaces a failing circulation pump, recharges the expansion vessel, and recommends system inhibitor/magnetic filter protection.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0
Professional Repair (Parts + Labor)$150 – $560

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: Vaillant F.75 (Pressure Sensor & Circulation Pump)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $150 – $560

Frequently Asked Questions

Can I clean or replace a Vaillant F.75 water pressure sensor myself?

No. Accessing internal wet hydraulic components and combustion seals inside a Vaillant ecoTEC boiler requires opening the appliance case, which must legally and safely be performed by a Gas Safe (or local national equivalent) certified heating engineer.

Why does Vaillant F.75 frequently happen right after bleeding radiators?

Bleeding radiators drops cold static pressure below ~0.8–1.0 bar and can trap air near the pump or sensor. Always top the boiler back to 1.0–1.5 bar via the filling loop afterward and press Reset once.

Related Searches & Questions

Vaillant boiler fault F75 pressure jumpVaillant ecoTEC F.75 cost repairVaillant F.75 pressure sensor vs pumpVaillant F.75 0.05 bar reset

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

HVAC & Boilers →
Vaillant Boiler Fault F.75: No Pressure Jump Detected on Pump Start | FaultCodes.org