# Vaillant F.75: Vaillant Boiler Fault F.75: No Pressure Jump Detected on Pump Start

> **Quick Answer:** Fault code **F.75** on Vaillant ecoTEC boilers means the control board started the internal circulation pump and failed to measure the expected dynamic **pressure jump of at least `0.05 bar` (`50 mbar`)** within the first seconds before ignition. Check your boiler's cold static system pressure first: if it has dropped below `1.0 bar` (or `< 0.5 bar`), repressurize safely to **`1.0–1.5 bar`** via the external filling loop and perform **one single reset**. Never open the boiler combustion casing yourself—if `F.75` persists at `1.0–1.5 bar`, a Gas Safe / certified heating engineer must clean or replace the choked **water pressure sensor**, clear air locks, recharge the expansion vessel, or free a seized circulation pump ($150–$560 / £95–£390).

- **URL:** https://faultcodes.org/hvac/vaillant-f75
- **Category:** HVAC, Boilers & Heating
- **Brand / Standard:** Vaillant
- **System Area:** Pressure Sensor & Circulation Pump
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Professional Recommended
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
To prevent dry-firing an uncirculated heat exchanger, Vaillant software executes a pump pressure-pulse verification on every heat demand. As the circulation impeller accelerates, hydraulic head normally spikes pressure at the sensor by `≥ 0.05 bar` (`50 mbar`). If heating system sludge plugs the tiny brass sensor orifice, the pump rotor seizes, or low static pressure / flat expansion vessel absorbs the pulse, the boiler retries and then locks out on `F.75`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Required Pump-Start Pressure Jump | ≥ 0.05 bar (50 mbar) | Measured within first seconds of pump start before burner ignition |
| Normal Cold Static System Pressure | 1.0–1.5 bar | F.75 commonly triggers once static pressure drops below ~0.5–1.0 bar |
| Internal Boiler Access Rule | Gas Safe / Certified Engineer Only | Homeowners may only top up external loop & perform single reset |

## Commonly Affected Models & Service Bulletins
- Vaillant ecoTEC plus & ecoTEC pro Gas Condensing Boilers (VC / VCW Series)
- Vaillant ecoTEC exclusive & ecoCOMPACT Systems
- Vaillant atmoTEC / turboTEC Wall-Hung Boilers

## Common Symptoms
- Central heating and domestic hot water stop working with `F.75` and an hourglass/fault icon on the Vaillant display
- Static pressure reads under `1.0 bar`—or sits normal (`1.2–1.5 bar`) yet pump hums faintly without burner lighting
- Intermittent `F.75` lockouts during cold mornings when radiator valves are mostly shut or expansion vessel pressure has decayed

## Most Likely Root Causes
- Sludge, magnetite debris, or scale fouling the **electronic water pressure sensor** orifice (classic ecoTEC failure)
- Low cold static system pressure (`< 0.5–1.0 bar`) or deflated/ruptured **expansion vessel** damping the pump pulse
- Seized, air-locked, or failing internal **heating circulation pump** (including faulty pump capacitor/PWM board)
- Closed system isolation valves / TRVs eliminating minimum bypass circulation path

## Tools & Parts Reference
- External filling loop valve / key (homeowner pressure top-up to 1.0–1.5 bar)
- Certified engineer: OEM Vaillant Water Pressure Sensor & expansion vessel pump/gauge
- Certified engineer: Multimeter, circulation pump tester & magnetite flush kit

## Step-by-Step Troubleshooting & Fix
1. Verify cold system gauge pressure (`1.0–1.5 bar` target) and ensure key radiators/auto-bypass flow isn't completely shut off.
2. Top up cold static pressure via the external filling loop if below `1.0 bar`, vent radiators if gurgling, re-verify `1.0–1.5 bar`, and execute a single reset via the boiler fault-reset button.
3. If `F.75` returns with normal static pressure (`1.0–1.5 bar`), shut down the boiler and book a Gas Safe / certified heating engineer—never remove the sealed appliance front casing yourself.
4. The engineer removes and cleans/replaces the fouled **Vaillant water pressure sensor** (updating to the revised brass/anti-sludge revision if older), frees or replaces a failing circulation pump, recharges the expansion vessel, and recommends system inhibitor/magnetic filter protection.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$0 | $150–$560 |
| GBP | £0–£0 | £95–£390 |
| CAD | CA$0–CA$0 | CA$180–CA$680 |
| EUR | €0–€0 | €120–€480 |
| CHF | CHF 0–CHF 0 | CHF 190–CHF 720 |

## Frequently Asked Questions
### Can I clean or replace a Vaillant F.75 water pressure sensor myself?
No. Accessing internal wet hydraulic components and combustion seals inside a Vaillant ecoTEC boiler requires opening the appliance case, which must legally and safely be performed by a Gas Safe (or local national equivalent) certified heating engineer.

### Why does Vaillant F.75 frequently happen right after bleeding radiators?
Bleeding radiators drops cold static pressure below ~0.8–1.0 bar and can trap air near the pump or sensor. Always top the boiler back to `1.0–1.5 bar` via the filling loop afterward and press Reset once.


## Verified Official & Engineering References
- [Vaillant UK Support: Official Boiler Fault Codes (F.75)](https://www.vaillant.co.uk/homeowners/advice-and-knowledge/vaillant-boiler-fault-codes/) (Official Support)
- [Vaillant Deutschland: Heizung Service & Störungscodes](https://www.vaillant.de/heizung/service/stoerungscodes/) (Official Support)
- [Vaillant Official UK Homeowner Portal](https://www.vaillant.co.uk) (Official Support)
