FaultCodes.org
P0171OBD-IIFuel Trim & Air/O2 MeteringVerified Guide· Updated: Nov 22, 2026

P0171 Fault Code: System Too Lean (Bank 1)

Long-Term Fuel Trim on Bank 1 hit its upper enrichment limit (+25% to +36%) because excess unmeasured air entered combustion or fuel delivery fell short—commonly caused by split PCV/vacuum hoses, dirty MAF sensors, or weak fuel pumps.

Quick AnswerModerate — Plan Repair

Code P0171 means Bank 1's fuel-injection control hit its upper ceiling trying to add extra fuel (LTFT > +25% on Ford or 1.30–1.36 on GM platforms across two drive trips) because too much unmeasured air or too little fuel is reaching the cylinders. Short commutes are generally safe if idle isn't stalling, though running overly lean raises combustion temperatures. Check idle vs. 2,500 RPM trims immediately: high trims at idle that drop near 0% under RPM prove a vacuum leak (like split crankcase ventilation hoses cited in GM TSB MC-10114925), whereas trims climbing with load point to a dirty MAF sensor or weak fuel delivery ($10–$180 DIY; $160–$480 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$160 – $480

What This Fault Code Means

In closed-loop operation, the ECM adjusts injector pulse width via Short-Term (STFT) and learned Long-Term Fuel Trim (LTFT), where ±10% is normal. When Bank 1 LTFT saturates at +25% to +36% (P0171), the upstream oxygen sensor is merely reporting lean exhaust accurately—the O2 sensor itself is rarely the defective part.

Common Symptoms

  • Rough or surging idle that smooths out at highway speed (classic vacuum leak)
  • Check Engine Light accompanied by P0174 on V6/V8 engines sharing a common air leak or MAF
  • Hesitation under heavy acceleration or slight engine knocking/pinging when climbing hills

Most Likely Root Causes

  • Cracked intake accordion duct, leaking PCV / crankcase ventilation pipes (cited in GM V6/V8 TSB MC-10114925), or brittle vacuum elbows
  • Dirty or oil-coated Mass Air Flow (MAF) sensor wire under-reporting incoming airflow mass
  • Low fuel delivery pressure (weak electric fuel pump, clogged fuel filter) or restricted GDI fuel injectors (cited in Ford TSB MC-10190420)
  • Leaking intake manifold gaskets or exhaust leak directly ahead of the upstream B1S1 oxygen sensor

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Normal Closed-Loop Fuel Trim Window

Positive trim adds extra fuel for lean air; negative trim removes excess fuel

±10% combined STFT + LTFT
GM P0171 Trigger Threshold

Suspended temporarily during heavy EVAP purge flow or intrusive ECU tests

LTFT 1.30–1.36 (+30% to +36%, 2 trips)
Ford Gasoline Trigger Threshold

High trim only at idle = air leak; rising with engine load = fuel shortage or low MAF

LTFT > +25% with STFT > +1% (2 trips)

Commonly Affected Models & Service Bulletins

  • GM V6 & V8 Engines with leaking PCV / crankcase ventilation pipes (NHTSA TSB MC-10114925)
  • Ford Gasoline & Direct-Injection Platforms (Motorcraft OBD Summary & NHTSA TSB MC-10190420)
  • Vehicles with cracked accordion intake ducts, dry PCV elbows, or oiled aftermarket air filters fouling the MAF

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1View live OBD-II STFT B1 + LTFT B1 at warm idle vs. steady 2,500 RPM no-load: if trim drops from +28% toward 0% under RPM, you have an unmetered intake vacuum leak; if trim rises even higher under load, test MAF g/s and fuel rail pressure.
  2. 2Inspect rubber intake ducts after the MAF, PCV valve grommets, and brake-booster hoses, then smoke-test the intake manifold at ~1–2 psi.
  3. 3Check whether P0174 (Bank 2) is also stored: P0171 + P0174 isolates shared components (air boot, MAF, fuel pump, shared PCV line) ahead of cylinder-head gaskets.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Do live STFT+LTFT readings sit high (+20–35%) at idle and drop sharply toward 0% when holding 2,500 RPM?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II scanner with live STFT / LTFT & MAF (g/s)Intake smoke leak tester (1–2 psi low pressure)Dedicated MAF Sensor Cleaner sprayFuel rail pressure gauge
  1. 1Replace any split rubber air intake ducts, leaking crankcase ventilation (PCV) hoses, or intake manifold gaskets revealed by smoke testing.
  2. 2Clean a fouled MAF sensor element carefully using dedicated MAF Sensor Cleaner spray (never brake/carb cleaner) and allow 15 minutes to air dry.
  3. 3Measure actual fuel rail pressure vs. factory specification at idle and snap-throttle; replace a restricted fuel filter or weak fuel pump assembly if pressure sags.
  4. 4Test injector balance/flow on direct-injection engines if fuel pressure and vacuum seals test clean, clear P0171, and verify combined STFT+LTFT settles within ±10%.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$10 – $180
Professional Repair (Parts + Labor)$160 – $480

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Should I replace the oxygen sensor first when I get code P0171?

No! Official GM and Ford OBD diagnostics note that the Bank 1 upstream O2 sensor is accurately reporting lean exhaust rather than causing it—smoke-test for vacuum leaks and clean the MAF sensor first.

Why do P0171 and P0174 show up together?

Both banks of a V6 or V8 engine share the intake snorkel, MAF sensor, central PCV hose, and fuel pump—so any single tear or fuel-pressure drop skews Bank 1 (P0171) and Bank 2 (P0174) simultaneously.

Related Searches & Questions

p0171p0171 codep0171 chevyp0171 toyotap0171 fordp0171 code chevyp0171 and p0174p0171 hondap0171 engine codep0171 nissanp0171 meaningp0171 meaning car code

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
P0171 Fault Code: System Too Lean (Bank 1) — Causes, Fixes & Cost | FaultCodes.org