FaultCodes.org
P0301OBD-IIIgnition & Misfire SystemVerified Guide· Updated: Nov 22, 2026

P0301 Fault Code: Cylinder 1 Misfire Detected

Over 90% of detected crankshaft-speed misfires are occurring specifically on Cylinder 1—commonly solved cleanly via a 5-minute coil/spark plug swap test to isolate a bad Cylinder 1 ignition coil, cracked plug insulator, or clogged injector.

Quick AnswerHigh — Service Soon

Code P0301 means more than 90% of engine misfires monitored via crankshaft speed fall specifically on Cylinder 1. Stop driving immediately if the Check Engine Light is FLASHING, which indicates catalyst-damaging misfires (>= 5% per 200 crankshaft revolutions per CARB criteria) where Ford/GM ECUs often shut down Cylinder 1 fuel injection to prevent converter damage. Solid lights trigger at >= 1% per 1,000 revs across two trips (GM ~2–5%, Ford 0.9–1.5%). Perform a zero-cost coil swap test: move Cylinder 1 ignition coil to Cylinder 2 (and swap spark plug to Cylinder 3 if still unsure)—if P0301 moves to P0302 (or P0303), you have proven the exact bad part ($25–$165 DIY; $160–$480 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$160 – $480

What This Fault Code Means

Each time Cylinder 1 fires cleanly, the crankshaft accelerates measurably on the Crankshaft Position Sensor. When Cylinder 1 fails to combust—due to a dying ignition coil, cracked ceramic spark-plug insulator (flagged in FCA NHTSA TSBs), clogged fuel injector, or low mechanical compression—the ECM attributes >90% of missed impulses to Cylinder #1 and triggers P0301.

Common Symptoms

  • Engine shakes noticeably at idle, stalls at stoplights, or stumbles/hesitates under acceleration
  • Flashing Check Engine Light under highway load (catalyst protection warning—pull over cleanly)
  • Raw gasoline smell from exhaust or paired P0316 (startup misfire)

Most Likely Root Causes

  • Failing Cylinder 1 ignition coil (including internal coil insulation breakdown cited in Mazda/OEM bulletins) or cracked rubber coil boot
  • Fouled/eroded Cylinder 1 spark plug, wrong electrode gap, or cracked porcelain insulator during prior installation (cited in NHTSA TSBs)
  • Clogged, leaking, or dead-coil Cylinder 1 fuel injector (P0201) or rodent-chewed coil/injector plug
  • Cylinder 1 mechanical fault (head-gasket coolant seepage, carbon-caked intake valve, burned exhaust valve, or worn piston rings)

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Cylinder-1 Isolation Rule

Assigned via instantaneous crankshaft acceleration tracking

> 90% of misfires on Cylinder 1
Catalyst-Damaging Rate (Flashing MIL)

Ford/GM ECUs may shut off Cylinder 1 injector until fault stabilizes

>= 5% per 200 crankshaft revolutions
Emissions Rate (Solid MIL, 2 trips)

Triggers steady Check Engine Light on consecutive drive trips

>= 1% per 1,000 revs (GM ~2–5%, Ford 0.9–1.5%)
Definitive Swap Isolation Test

Migrating to P0302/P0303 isolates faulty ignition component at $0 cost

Swap Coil 1 -> Cyl 2, Plug 1 -> Cyl 3

Commonly Affected Models & Service Bulletins

  • 4-Cylinder & V6/V8 Platforms with failing individual ignition coils or installation-cracked spark plug insulators (NHTSA TSBs SB-10084296, MC-10186907, MC-10241133)
  • Ford & GM engines enforcing automatic Cylinder 1 injector shutoff during >=5% catalyst-damaging misfire events
  • High-mileage direct-injection engines experiencing carbon-fouled intake valves or clogged Cylinder 1 injectors

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Safety Check: If the MIL flashes, pull off the road immediately before hot catalytic substrate melts.
  2. 2Swap ONLY the Cylinder 1 ignition coil with Cylinder 2 (keep Cylinder 1's spark plug untouched first), clear codes, start/idle briefly, and scan OBD-II Mode $06 misfires: if misfire jumps to Cylinder 2 (`P0302`), replace the faulty coil immediately.
  3. 3If misfire stays on Cylinder 1, pull the Cylinder 1 spark plug to inspect for oil in the plug well, white coolant washing, or hairline ceramic cracks—and swap the spark plug with Cylinder 3 to see if misfire moves to P0303.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

After swapping Cylinder 1 ignition coil to Cylinder 2, does the misfire counter or DTC move to Cylinder 2 (P0302)?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II scanner with Mode $06 per-cylinder misfire counterSpark plug socket, extension & calibrated torque wrenchFeeler spark-plug gap gauge & multimeterCompression gauge (if misfire fails to migrate with coil/plug)
  1. 1Inspect Cylinder 1 coil & injector harness plugs first for oil intrusion (leaking valve cover gasket) or rodent chew marks.
  2. 2Run the coil swap (Cyl 1 <-> Cyl 2) and spark-plug inspection (Cyl 1 <-> Cyl 3): replace a confirmed dead OEM ignition coil or replace the overdue full set of properly gapped OEM spark plugs.
  3. 3If BOTH coil and plug swaps leave misfire stubbornly locked on Cylinder 1, test Cylinder 1 injector click/ohm resistance (~11–16 Ω port injection) and listen with a mechanic stethoscope.
  4. 4If spark and fuel pulses both test strong yet Cylinder 1 still misses at idle, run a Cylinder 1 compression & leakdown test to catch burned valves, blown head-gasket coolant intrusion, or collapsed lifters.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$25 – $165
Professional Repair (Parts + Labor)$160 – $480

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Where is Cylinder 1 located on my engine?

On almost all inline 4-cylinder engines, Cylinder 1 is closest to the front serpentine/timing belt end. On V6/V8 engines, Bank 1 always contains Cylinder 1—check your specific vehicle's cylinder firing-order diagram before swapping coils.

Should I replace all ignition coils or just the bad Cylinder 1 coil?

Spark plugs should always be replaced together as a full set due to even wear. For expensive OEM coil-on-plug packs, replacing just the proven failed Cylinder 1 coil is fine unless the remaining original coils have >100,000 miles and share age cracks.

Related Searches & Questions

p0301p0301 codep0301 engine codep0301 fordp0301 hondap0301 toyotap0301 code causesp0301 code chevyp030100p0301 cylinder 1 misfirep0301 meaningp0301 code meaning

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
P0301 Fault Code: Cylinder 1 Misfire Detected — Causes, Fixes & Cost | FaultCodes.org