# OBD-II P0301: Cylinder 1 Misfire Detected

> **Quick Answer:** Code P0301 means **more than 90%** of engine misfires monitored via crankshaft speed fall specifically on **Cylinder 1**. **Stop driving immediately if the Check Engine Light is FLASHING**, which indicates catalyst-damaging misfires (`>= 5%` per 200 crankshaft revolutions per CARB criteria) where Ford/GM ECUs often shut down Cylinder 1 fuel injection to prevent converter damage. Solid lights trigger at `>= 1%` per 1,000 revs across two trips (`GM ~2–5%`, `Ford 0.9–1.5%`). Perform a zero-cost **coil swap test**: move Cylinder 1 ignition coil to Cylinder 2 (and swap spark plug to Cylinder 3 if still unsure)—if `P0301` moves to `P0302` (or `P0303`), you have proven the exact bad part ($25–$165 DIY; $160–$480 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0301
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Ignition & Misfire System
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Each time Cylinder 1 fires cleanly, the crankshaft accelerates measurably on the Crankshaft Position Sensor. When Cylinder 1 fails to combust—due to a dying ignition coil, cracked ceramic spark-plug insulator (flagged in FCA NHTSA TSBs), clogged fuel injector, or low mechanical compression—the ECM attributes >90% of missed impulses to Cylinder #1 and triggers P0301.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Cylinder-1 Isolation Rule | > 90% of misfires on Cylinder 1 | Assigned via instantaneous crankshaft acceleration tracking |
| Catalyst-Damaging Rate (Flashing MIL) | >= 5% per 200 crankshaft revolutions | Ford/GM ECUs may shut off Cylinder 1 injector until fault stabilizes |
| Emissions Rate (Solid MIL, 2 trips) | >= 1% per 1,000 revs (GM ~2–5%, Ford 0.9–1.5%) | Triggers steady Check Engine Light on consecutive drive trips |
| Definitive Swap Isolation Test | Swap Coil 1 -> Cyl 2, Plug 1 -> Cyl 3 | Migrating to P0302/P0303 isolates faulty ignition component at $0 cost |

## Commonly Affected Models & Service Bulletins
- 4-Cylinder & V6/V8 Platforms with failing individual ignition coils or installation-cracked spark plug insulators (NHTSA TSBs SB-10084296, MC-10186907, MC-10241133)
- Ford & GM engines enforcing automatic Cylinder 1 injector shutoff during >=5% catalyst-damaging misfire events
- High-mileage direct-injection engines experiencing carbon-fouled intake valves or clogged Cylinder 1 injectors

## Common Symptoms
- Engine shakes noticeably at idle, stalls at stoplights, or stumbles/hesitates under acceleration
- Flashing Check Engine Light under highway load (catalyst protection warning—pull over cleanly)
- Raw gasoline smell from exhaust or paired `P0316` (startup misfire)

## Most Likely Root Causes
- Failing **Cylinder 1 ignition coil** (including internal coil insulation breakdown cited in Mazda/OEM bulletins) or cracked rubber coil boot
- Fouled/eroded **Cylinder 1 spark plug**, wrong electrode gap, or **cracked porcelain insulator** during prior installation (cited in NHTSA TSBs)
- Clogged, leaking, or dead-coil **Cylinder 1 fuel injector** (`P0201`) or rodent-chewed coil/injector plug
- Cylinder 1 mechanical fault (head-gasket coolant seepage, carbon-caked intake valve, burned exhaust valve, or worn piston rings)

## Tools & Parts Reference
- OBD-II scanner with Mode $06 per-cylinder misfire counter
- Spark plug socket, extension & calibrated torque wrench
- Feeler spark-plug gap gauge & multimeter
- Compression gauge (if misfire fails to migrate with coil/plug)

## Step-by-Step Troubleshooting & Fix
1. Inspect Cylinder 1 coil & injector harness plugs first for oil intrusion (leaking valve cover gasket) or rodent chew marks.
2. Run the coil swap (`Cyl 1 <-> Cyl 2`) and spark-plug inspection (`Cyl 1 <-> Cyl 3`): replace a confirmed dead **OEM ignition coil** or replace the overdue full set of properly gapped OEM spark plugs.
3. If BOTH coil and plug swaps leave misfire stubbornly locked on Cylinder 1, test Cylinder 1 injector click/ohm resistance (`~11–16 Ω` port injection) and listen with a mechanic stethoscope.
4. If spark and fuel pulses both test strong yet Cylinder 1 still misses at idle, run a **Cylinder 1 compression & leakdown test** to catch burned valves, blown head-gasket coolant intrusion, or collapsed lifters.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $25–$165 | $160–$480 |
| GBP | £20–£130 | £125–£375 |
| CAD | CA$35–CA$215 | CA$210–CA$625 |
| EUR | €22–€150 | €145–€430 |
| CHF | CHF 28–CHF 180 | CHF 190–CHF 540 |

## Frequently Asked Questions
### Where is Cylinder 1 located on my engine?
On almost all inline 4-cylinder engines, **Cylinder 1 is closest to the front serpentine/timing belt end**. On V6/V8 engines, Bank 1 always contains Cylinder 1—check your specific vehicle's cylinder firing-order diagram before swapping coils.

### Should I replace all ignition coils or just the bad Cylinder 1 coil?
Spark plugs should always be replaced together as a full set due to even wear. For expensive OEM coil-on-plug packs, replacing just the proven failed Cylinder 1 coil is fine unless the remaining original coils have >100,000 miles and share age cracks.


## Verified Official & Engineering References
- [OBD-II Misfire Threshold Regulation (13 CCR 1968.2)](https://www.law.cornell.edu/regulations/california/13-CCR-1968.2) (Regulation / Standard)
- [GM Engine OBD Diagnostics Mode 6 (18OBDG03A)](https://gsi.ext.gm.com/gmspo/mode6/pdf/2018/18OBDG03A%20Engine%20Diagnostics.pdf) (Technical Manual)
- [NHTSA Service Bulletin SB-10084296 (Cylinder Misfire)](https://static.nhtsa.gov/odi/tsbs/2016/SB-10084296-2280.pdf) (Service Bulletin (TSB))
- [NHTSA Service Bulletin MC-10241133 (Ignition & Misfire)](https://static.nhtsa.gov/odi/tsbs/2023/MC-10241133-9999.pdf) (Service Bulletin (TSB))
