OBD-II Fault Codes & Error Guide
9,533 indexed OBD-II fault codes in Automotive & OBD-II with plain-English causes, safety ratings, and repair cost ranges.
Our OBD-II index covers 9,533 fault codes in Automotive & OBD-II, led by high-frequency lookups like P0420, P0300, P0171, P0128. Of these, 5,226 carry high or critical urgency ratings requiring prompt inspection.
- Auto & OBD-II
- 9,533 codes indexed
- Urgency
- 5,226 high / critical
- Popular Fault Codes
- P0420
Catalyst System Efficiency Below Threshold (Bank 1)
The Bank 1 catalytic converter fell below oxygen-storage or thermal efficiency thresholds compared with upstream sensor readings—caused by catalyst aging, oil/misfire poisoning, exhaust leaks ahead of Sensor 2, or skewed O2 sensors.
Random / Multiple Cylinder Misfire Detected
Crankshaft speed monitoring detected engine misfires across multiple cylinders (or changing randomly)—triggering a solid Check Engine light at ~1–2%+ emissions rate and a FLASHING warning light at >= 5% catalyst-damaging misfire rate.
System Too Lean (Bank 1)
Long-Term Fuel Trim on Bank 1 hit its upper enrichment limit (+25% to +36%) because excess unmeasured air entered combustion or fuel delivery fell short—commonly caused by split PCV/vacuum hoses, dirty MAF sensors, or weak fuel pumps.
Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
Engine coolant took too long to reach regulating temperature after a cold start—such as falling below ~65 °C on GM heat models or <78 °C on Ford 89 °C thermostats—overwhelmingly caused by a stuck-open thermostat.
Evaporative Emission (EVAP) System Small Leak Detected (0.040" / 1 mm)
Fuel vapor containment failed a ~0.040 in (1 mm) / 0.020 in pressure-decay leak test—most commonly caused by a loose or cracked rubber gas cap gasket, split EVAP purge hose, or leaking canister vent seal.
Evaporative Emission (EVAP) System Large Leak Detected
Zero tank vacuum built up during the EVAP pull-down test—such as failing to reach ~-2 kPa in 30 s (Ford) or 2,740 Pa after 20 L purge (GM)—usually caused by a missing/loose gas cap, popped EVAP hose, stuck-open vent valve, or stuck-closed purge solenoid.
Cylinder 1 Misfire Detected
Over 90% of detected crankshaft-speed misfires are occurring specifically on Cylinder 1—commonly solved cleanly via a 5-minute coil/spark plug swap test to isolate a bad Cylinder 1 ignition coil, cracked plug insulator, or clogged injector.
OBD-II P0174: System Too Lean (Bank 2)
SAE J2012 code set when Long Term Fuel Trim exceeds roughly `+20% to +25%` trying to keep Bank 2 (opposite cylinder #1) at `14.7:1`—compare freeze-frame idle vs 2,500 RPM trims and whether P0171 co-occurs.
OBD-II P0401: Exhaust Gas Recirculation (EGR) Flow Insufficient Detected
SAE J2012 emissions code set when EGR valve commands fail to produce expected **DPFE pressure, MAP/MAF change, or EGR temperature rise**—often caused by **carbon-clogged intake ports or failing DPFE sensors** rather than the valve itself.
OBD-II P0135: O2 Sensor Heater Circuit (Bank 1, Sensor 1)
SAE J2012 heater circuit fault on upstream **Bank 1 Sensor 1** oxygen sensor—measure heater pins (`2–15 Ω` normal; `> 100 Ω / OL` open, `< 0.5 Ω` short) and confirm **12 V fuse feed + PCM PWM ground** during the `2–5 s` cold-start check.
OBD-II P0430: Catalyst System Efficiency Below Threshold (Bank 2)
Bank 2 catalytic converter **oxygen storage capacity (OSC)** monitor failed because downstream **B2S2** O2 voltage swings like upstream **B2S1** instead of holding steady `~0.6–0.7 V`—rule out **exhaust leaks, misfires, and fuel trims** before replacing the Bank 2 cat.
OBD-II P0101: Mass Air Flow (MAF) Sensor Range/Performance
Measured **MAF `g/s`** airflow deviates **`> 20% to 35%`** from the PCM's `RPM/MAP/TPS` airflow model for `2–4 s` steady-state—check **split intake boots, dirty hot-wire elements** (clean only with MAF-safe spray), **clogged air filters, or sticking PCV valves**.
OBD-II P0302: Cylinder 2 Misfire Detected
Mode `$06` **Cylinder 2** misfire counter exceeded threshold—use fast **coil-swap + plug-swap isolation** (`#2 -> #1/#3` to see if code moves to `P0301/P0303`), check **spark gap, injector pulse & compression (`~120–180 psi`, within `10–15%`)**; **STOP immediately if the CEL flashes** (catalyst meltdown hazard).
OBD-II P0303: Cylinder 3 Misfire Detected
Mode `$06` **Cylinder 3** misfire monitor triggered—swap **Coil #3 -> #1/#2** and **Plug #3 -> a separate cylinder** to pinpoint coil vs plug vs injector/compression; check **oil inside the #3 spark plug well** (valve cover gasket) and **stop immediately if the CEL flashes**.
OBD-II P0304: Cylinder 4 Misfire Detected
Mode `$06` **Cylinder 4** misfire counter exceeded limit—swap **Coil #4 -> #1/#2**, inspect plug wear/carbon tracking, test **injector resistance (`~11–16 Ω` port injection) + noid light**, and check **compression/leakdown** if #4 stays dead; **STOP if the CEL flashes**.
OBD-II P0440: Evaporative Emission (EVAP) Control System Malfunction
General EVAP self-test fail across purge, vent, or tank sealing—check **gas cap O-ring** first, then ohm-test **purge (`18–30 Ω`) & vent (`20–40 Ω`) solenoids**, verify **FTP sensor baseline (`~2.5–3.0 V` KOEO cap off)**, and pinpoint leaks with a **low-pressure EVAP smoke test**.
OBD-II P0456: EVAP System Very Small Leak Detected (0.020 in)
CARB/EPA **`0.020-inch (0.5 mm)` micro-leak** threshold tripped (half the `0.040 in` P0442 pinhole)—inspect the **gas cap gasket & rusted filler neck lip**, check **purge valve weep**, and pinpoint with a **low-pressure EVAP smoke tester (`~0.5–1.0 psi`)**.
OBD-II P0118: Engine Coolant Temperature (ECT) Circuit High Input
NTC thermistor signal pulled **`≥ 4.6 V`** (open circuit / infinite resistance), defaulting PCM coolant temp to **`-40 °C (-40 °F)`**—causes **hard cold starts, over-rich fueling & cooling fans locked ON**; inspect unplugged/corroded pins and test the **ohm curve (`~2–3 kΩ @ 20 °C` -> `~200–300 Ω @ 90 °C`)**.
OBD-II P0340: Camshaft Position Sensor "A" Circuit (Bank 1)
Missing or erratic **Bank 1 Intake Camshaft Position (CMP)** signal (3-wire `5V/12V` Hall-effect square wave or 2-wire VR AC pulse), causing **extended cranking, stalling, or no-start**—test **`5 V / 12 V` reference + ground + signal continuity**, clean **metallic debris off sensor tip**, and inspect **timing belt/chain slack**.
OBD-II P0507: Idle Air Control (IAC) System RPM Higher Than Expected
Actual warm idle exceeds target map by **`> 100–200 RPM`** continuously (`5–10 s`) while throttle is closed—check **unmetered intake vacuum leaks**, **carbon-bound Electronic Throttle Body (ETB) / IACV**, and run the **OEM Idle Air Volume Relearn** after cleaning.
OBD-II P0700: Transmission Control System (MIL Request)
Informational **ECM flag** proving the **Transmission Control Module (TCM)** stored active fault(s)—generic OBD-II scanners **only show `P0700`**; use an **enhanced/OEM all-module scanner** to pull the true TCM root code (`P0715`, `P0730`, `P0741`, solenoid codes) and check **ATF level/condition + battery voltage** first.
OBD-II P0011: "A" Camshaft Position Timing Over-Advanced (Bank 1)
Bank 1 intake camshaft phaser stays **over-advanced** vs crankshaft target—**check engine oil level & sludge condition FIRST**, then ohm-test **VVT Oil Control Valve (OCV) solenoid (`6.0–12.0 Ω @ 20 °C`, `OL` to ground, 12V bench click)**, clean **clogged VVT oil screens**, and check for a **stretched timing chain**.
OBD-II P0141: O2 Sensor Heater Circuit (Bank 1, Sensor 2)
Downstream post-cat **Bank 1 Sensor 2** heater circuit fault—measure heater pins (**`2–15 Ω` normal**, **`> 100 Ω / OL` open**, **`< 0.5 Ω` short**) and inspect the **dedicated heater fuse, road-salt corroded underbody pins**, and **`12 V` feed + PCM PWM ground**.
OBD-II P0325: Knock Sensor 1 Circuit (Bank 1)
Piezoelectric **Bank 1 Knock Sensor (`KS1`)** circuit open/shorted or producing zero detonation voltage—PCM **retards ignition timing** conservatively (causing **sluggish acceleration & lower MPG**); check **rodent-chewed under-manifold knock harness**, verify **exact mounting bolt torque**, and test **resistance / AC mV tap response**.
OBD-II P0446: EVAP Emission Control System Vent Control Circuit
SAE J2012 emissions fault when the **canister vent solenoid** sticks closed/open, its **20–40 Ω** (up to **50–70 Ω**) coil circuit faults, or the charcoal canister fresh-air filter plugs—often causing **slow gas-pump click-offs** during refueling.
OBD-II P0102: Mass or Volume Air Flow (MAF) Sensor "A" Circuit Low Input
SAE J2012 powertrain fault when the **MAF signal drops below the hardware floor (`< 0.15–0.20 V` or near `0.0 g/s`)**—usually caused by an **unplugged connector, blown MAF fuse, open wire/short to ground, or oil-fouled hot-wire element**.
OBD-II P0113: Intake Air Temperature (IAT) Sensor 1 Circuit High
SAE J2012 fault when an **open NTC circuit pulls the IAT line `> 4.6–4.85 V`**, locking PCM air-temp readings at **`< -40 °C (-40 °F)`**—extremely common right after an air filter change leaves an **integrated MAF/IAT plug unplugged**.
OBD-II P0172: System Too Rich (Bank 1)
SAE J2012 fuel-trim fault triggered when Bank 1 adaptive **Long-Term Fuel Trim (`LTFT`) drops below `-20% to -25%`**—caused by a **stuck-open EVAP purge valve (`P0496`), leaking fuel injector, oil-fouled MAF over-reporting air, high fuel pressure, or skewed cold ECT sensor**.
OBD-II P0335: Crankshaft Position (CKP) Sensor "A" Circuit
Critical SAE J2012 powertrain fault—loss of primary **CKP RPM/TDC signal** leaves the engine **cranking with `0 RPM` on tachometer/scanner and NO spark or fuel injector pulse**; check **`5 V / 12 V` Hall supply** or **VR coil (`~300–1,500 Ω`)**, **oil-soaked crank-pulley wiring**, and **damaged reluctor teeth**.
OBD-II P0411: Secondary Air Injection (SAIR) System Incorrect Flow Detected
SAE J2012 cold-start emissions code triggered when the **SAIR pump fails to produce an expected lean O2 shift within `2–5 s` of activation** (or sufficient secondary air pressure)—check **SAIR fuse/relay, water-logged electric pump, rusted combi check valves, and cracked vacuum lines**.
OBD-II P2096: Post Catalyst Fuel Trim System Too Lean (Bank 1)
SAE J2012 trim-bias fault when the **downstream post-cat O2 sensor stays biased lean (`< 0.45 V` / `λ > 1.02`) over steady cruise integration**—most commonly caused by a **small exhaust leak between upstream and downstream O2 sensors** (flex pipe/flange), a **skewed rear O2 sensor**, **fuel-starved Bank 1**, or **degraded catalyst oxygen storage**.
OBD-II P0016: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A)
Critical SAE J2012 mechanical phase-timing fault between the **crankshaft and Bank 1 intake camshaft (`Sensor A`)**—**STOP driving interference engines aggressively** to prevent piston-to-valve collision; verify **oil level/sludge & VVT OCV (`6–12 Ω`)** first, then check for a **stretched timing chain, jumped timing belt, failed tensioner, or slipped reluctor via dual-channel oscilloscope**.
OBD-II P0193: Fuel Rail Pressure (FRP) Sensor "A" Circuit High Input
SAE J2012 high-pressure fuel fault when a **returnless port or GDI rail sensor clips `> 4.8–4.95 V` (against the `5.0 V` reference)**, triggering limp-home mode—inspect for **open sensor ground, signal short to `5 V`, unplugged rail sensor**, and compare **mechanical vs scan-tool rail pressure (`~35–65 psi` port / `500–2,500+ psi` GDI)**.
OBD-II P0496: EVAP System High Purge Flow (Flow During Non-Purge)
SAE J2012 EVAP fault when the **canister purge solenoid sticks physically open**, drawing **continuous intake vacuum into the fuel tank even when commanded `0%` closed**—famous for causing **hard starts right after filling the gas tank**; verify via idle hose suction test and coil check (`18–30 Ω`).
OBD-II P0715: Input/Turbine Shaft Speed Sensor "A" Circuit
SAE J2012 transmission fault when the **TCM loses the input/turbine shaft RPM signal**, triggering **harsh/delayed shifts or 2nd/3rd gear limp mode**—inspect **ATF level/metal shavings**, **connector oil wicking**, and measure **VR coil resistance (`~300–1,200 Ω`)** or **Hall-effect `5 V / 12 V` reference**.
OBD-II U0100: Lost Communication With ECM/PCM "A" (CAN Bus Timeout)
Critical SAE J2012 network fault—CAN-H / CAN-L bus nodes lost the **ECM/PCM heartbeat**; check **battery voltage (`≥ 12.6 V` KOEO) and ECM main fuses/relays FIRST**, then (with **battery disconnected**) measure **OBD-II Pin 6 (CAN-H) to Pin 14 (CAN-L) = `60 Ω` normal** (`120 Ω` open leg, `0 Ω` shorted bus).
OBD-II C0035: Left Front Wheel Speed Sensor Circuit (ABS / ESC Fault)
SAE J2012 chassis fault—**ABS, ESC & Traction Control lights illuminate** and ABS disables while base hydraulic brakes still work cautiously; inspect **front-left wheel-well harness flex cracks, rust-jacked air gap / cracked tone ring, loose wheel bearing play**, and check **2-wire passive ohms (`~800–2,000 Ω`) or active live wheel speed parity (`0 km/h` mismatch)**.
OBD-II B0001: Driver Frontal Stage 1 Deployment Control Circuit (SRS Airbag)
Critical SAE J2012 SRS restraint fault—**Airbag warning light stays ON and the driver frontal airbag is DISABLED in a crash**; **CRITICAL SAFETY RULE: NEVER probe SRS squib/inflator pins with a standard ohmmeter** (meter test current can fire the airbag!). Certified techs disconnect 12V negative for **≥ 10–15 min** and use an approved **`~2.0–2.5 Ω` SRS simulator** to isolate the **clock spring** (often with dead horn/steering buttons), **yellow SRS connectors**, or **SRS module**.
Turbocharger / Supercharger "A" Underboost Condition
Actual boost pressure lagged significantly behind target boost—such as >4 psi (28 kPa) for 5 seconds on Ford EcoBoost or 30–55 kPa below target on GM petrol engines—most commonly caused by boost hose leaks, worn wastegate rods, diverter diaphragms, or winter intercooler icing.
OBD-II P0441: Evaporative Emission (EVAP) System Incorrect Purge Flow
SAE J2012 EVAP code triggered when the PCM sees **purge flow while commanded closed OR zero vacuum/pressure drop when commanded open**—inspect **split purge vacuum lines**, test **purge solenoid (`18–30 Ω`) & idle suction**, check **canister vent valve (`20–40 Ω`)**, and verify **FTP atmospheric voltage (`~2.5–3.0 V` cap off)**.
OBD-II P0175: System Too Rich (Bank 2)
SAE J2012 code set when Bank 2 adaptive Long Term Fuel Trim drops below `-20% to -25%` trying to lean out an over-fueled cylinder bank—check whether `P0172` co-occurs to isolate global MAF/fuel-pressure/EVAP purge faults vs Bank 2 injectors or O2 bias.
OBD-II P0014: "B" Camshaft Position Timing Over-Advanced or System Performance (Bank 1)
Exhaust (`"B"`) camshaft phaser on Bank 1 stayed over-advanced or lagged behind ECM target—check engine oil level, viscosity, and sludge FIRST, ohm-test the exhaust VVT OCV solenoid (`6.0–12.0 Ω` @ `20 °C`), and inspect clogged oil screens or cam phaser lock pins.
OBD-II P0138: O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)
Downstream post-catalyst zirconia O2 sensor (`B1S2`) stays pinned `> 0.80–0.90 V` continuously—inspect for melted signal wire shorted to `12 V` heater power, chronically rich running (`P0172`), or an internally shorted sensor before swapping parts.
OBD-II P0133: O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)
Upstream Bank 1 Sensor 1 (`B1S1`) cross-count transition across `450 mV` exceeds `~100–300 ms`—graph live `0.1–0.9 V` waveform oscillation and rule out pre-cat exhaust leaks, fuel-trim bias, or silicone/coolant poisoning before replacing `B1S1`.
OBD-II P0131: O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)
Upstream `B1S1` O2 signal stayed pinned `< 150–200 mV` for `> 2–5 s` in closed loop—use a brief intake fuel-enrichment pulse (`> 0.8 V` jump proves the sensor works!) to separate severe vacuum/fuel starvation from a shorted ground wire or dead sensor.
OBD-II P0449: EVAP System Vent Valve / Solenoid Control Circuit
Pure electrical open or short circuit in the rear charcoal canister vent valve solenoid—frequently triggered by road-salt pigtail corrosion; check the EVAP fuse, verify `20–40 Ω` solenoid coil resistance, and test `12 V` ignition feed plus ECM ground control.
OBD-II P0451: EVAP System Pressure Sensor / Switch Range / Performance
Fuel Tank Pressure (`FTP`) sensor reads erratically, drifts, or stays stuck off atmospheric baseline—verify KOEO open-cap baseline (`~2.5–3.0 V` by OEM), `5.0 V` reference/ground, plugged canister vent, or corroded top-of-tank FTP plug.
OBD-II P0562: System Voltage Low (Battery / Alternator Charging Fault)
ECM battery/ignition supply dropped below `~10.0–11.0 V`—measure KOEO resting voltage (`~12.6 V`) and running load voltage (`13.5–14.5 V` @ idle & `2,000 RPM`); ALWAYS fix `P0562` FIRST because sagging voltage triggers false `U0100`, `P2135`, and `P0016` codes.
Frequently Asked Questions
What are the most common OBD-II fault codes?
Among 9,533 indexed OBD-II codes in Automotive & OBD-II, top lookups include P0420, P0300, P0171, P0128. Each diagnostic page breaks down root causes, a 3-step triage check, and realistic repair cost benchmarks.
Is it safe to keep driving or operating OBD-II with a fault code?
Of the 9,533 documented OBD-II codes, 4,310 are typically safe for limited short-term operation, whereas 5,226 carry high or critical urgency warnings. Always inspect the safety rating on the specific code guide before continuing.
How do I troubleshoot a OBD-II error code step by step?
Select your exact fault code (such as P0420) from the directory above, review the Quick Answer box, and run through the Interactive Symptom Triage to isolate wiring or sensor issues before purchasing replacement parts.