FaultCodes.org
P0335OBD-IIIgnition & Misfire SystemVerified Guide· Updated: Nov 22, 2026

OBD-II P0335: Crankshaft Position (CKP) Sensor "A" Circuit

Critical SAE J2012 powertrain fault—loss of primary CKP RPM/TDC signal leaves the engine cranking with `0 RPM` on tachometer/scanner and NO spark or fuel injector pulse; check `5 V / 12 V` Hall supply or VR coil (`~300–1,500 Ω`), oil-soaked crank-pulley wiring, and damaged reluctor teeth.

Quick AnswerCritical — Stop Immediately

Code P0335 (SAE J2012) signals loss or corruption of the Crankshaft Position (CKP) Sensor "A" circuit—the primary engine RPM and Top Dead Center (TDC) timing reference. Because the PCM cannot synchronize ignition or fuel injection without it, do not drive: the engine commonly stalls suddenly at speed or cranks endlessly with `0 RPM` shown on a live OBD-II scanner (and flat tachometer), zero spark, and zero injector pulse. Inspect oil-soaked wiring near the harmonic balancer/crank pulley, test Hall-effect `5 V / 12 V` supply & ground or 2-wire Variable Reluctance (VR) coil resistance (`~300–1,500 Ω`), and check for chipped reluctor tone-ring teeth before swapping parts ($30–$140 DIY; $190–$460 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$190 – $460

What This Fault Code Means

A 2-wire inductive Variable Reluctance (VR) sensor generates an AC sine wave as notched crank reluctor teeth sweep past its magnet, whereas a 3-wire Hall-effect or magneto-resistive sensor switches a sharp 0–5 V or 0–12 V square wave. Missing pulses, thermal open coils, oil-wicked connectors, or bent tone-wheel teeth interrupt crank synchronization and log P0335.

Common Symptoms

  • Engine cranks briskly but will NOT start with `0 RPM` on live scanner and dead tachometer needle
  • Sudden mid-drive stall (often returning after 15–30 minutes cool-down when a failing CKP coil thermally opens)
  • No ignition spark, no fuel-injector pulse, and extended cranking before delayed backup cam-sensor start on select platforms

Most Likely Root Causes

  • Failed Crankshaft Position (CKP) sensor failing thermally when hot or measuring outside ~300–1,500 Ω (2-wire VR) / dropping square wave (3-wire Hall)
  • Oil-soaked, heat-brittle wiring harness or melted connector routed beside the crank pulley or exhaust manifold
  • Damaged, rusted, or chipped crankshaft reluctor tone-ring teeth (or excessive axial crank thrust play)
  • Missing `5 V` / `12 V` supply or ground (3-wire Hall sensor) or loose sensor mounting bolt altering air gap

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Scanner Cranking Symptom

Primary RPM/TDC loss prevents PCM ignition & injection synchronization

0 RPM (no spark / no injector pulse)
2-Wire VR Coil Spec / 3-Wire Hall

Check supply + ground on 3-wire Hall; check ohms & AC pulse on 2-wire VR

~300–1,500 Ω VR | 5 V or 12 V Hall
Mechanical Failure Checks

Front crank seal oil leaks and chipped tone-wheel teeth mimic bad sensors

Oil-soaked crank plug & reluctor teeth

Commonly Affected Models & Service Bulletins

  • Nissan Altima / Maxima / Pathfinder VQ & QR engines (hot-stall CKP sensors)
  • Mercedes-Benz / BMW / Volkswagen / Audi (bellhousing VR & Hall CKP failures)
  • Chevrolet / Dodge / Jeep / Honda / Hyundai models (crank pulley harness & CKP faults)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Connect an OBD-II live-data scanner and watch Engine RPM while cranking: steady `0 RPM` confirms complete loss of CKP signal (verify strong 12.6 V battery / crisp cranking speed first).
  2. 2Inspect the lower engine block/bellhousing CKP connector for oil leaks soaking the plug and wires chafed near the crank pulley or serpentine belt.
  3. 3For 2-wire VR sensors, measure coil resistance (~300–1,500 Ω, check AC mV/oscilloscope cranking pulse); for 3-wire Hall sensors, verify 5 V or 12 V supply, ground, and 0–5 V/12 V switching pulse while cranking, then bore-scope reluctor ring teeth if signal dropouts repeat.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does live OBD-II scanner data read 0 RPM while the starter cranks the engine normally?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data scanner (monitoring cranking Engine RPM)Digital multimeter / lab oscilloscope (300–1,500 Ω VR or 5 V/12 V Hall pulse test)Inspection mirror / borescope & electrical contact cleaner
  1. 1Disconnect battery negative if working near the starter or crank pulley, clean oil buildup off the CKP plug with electrical contact cleaner, and fix any oil leak dripping onto the harness.
  2. 2Repair rubbed, heat-hardened, or oil-degraded wires using shielded/sealed splices routed clear of pulleys and belts.
  3. 3If 5 V/12 V power and ground test good (or 2-wire VR coil opens when heated/outside ~300–1,500 Ω), install an OEM-grade CKP sensor with a new O-ring and torque bolt accurately to protect air gap.
  4. 4Inspect reluctor tone ring through the sensor bore if needed, clear P0335, perform any OEM Crankshaft Position Variation Relearn, and verify crisp startup.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $140
Professional Repair (Parts + Labor)$190 – $460

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does my car stall when hot and restart 20 minutes later with P0335?

Failing crankshaft sensor windings expand with engine block heat and go open circuit (OL), cutting spark and fuel instantly; once cooled, copper contact closes briefly until permanently failing.

Is it safe to drive with code P0335?

No—P0335 can shut down ignition and fuel injection instantaneously at highway speeds, causing loss of power steering assist and brake vacuum booster reserve.

Related Searches & Questions

OBD2 P0335 crank no start 0 RPM scannerP0335 crankshaft sensor resistance ohms vs Hall 5V 12VP0335 stalls when warm restarts coolP0335 oil soaked wiring reluctor ring

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0335: Crankshaft Position (CKP) Sensor "A" Circuit | FaultCodes.org