# OBD-II P0335: OBD-II P0335: Crankshaft Position (CKP) Sensor "A" Circuit

> **Quick Answer:** Code **P0335** (SAE J2012) signals loss or corruption of the **Crankshaft Position (CKP) Sensor "A" circuit**—the primary engine RPM and Top Dead Center (TDC) timing reference. Because the PCM cannot synchronize ignition or fuel injection without it, **do not drive**: the engine commonly **stalls suddenly at speed or cranks endlessly with `0 RPM` shown on a live OBD-II scanner (and flat tachometer), zero spark, and zero injector pulse**. Inspect **oil-soaked wiring near the harmonic balancer/crank pulley**, test **Hall-effect `5 V / 12 V` supply & ground** or **2-wire Variable Reluctance (VR) coil resistance (`~300–1,500 Ω`)**, and check for **chipped reluctor tone-ring teeth** before swapping parts ($30–$140 DIY; $190–$460 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0335
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Ignition & Misfire System
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
A 2-wire inductive Variable Reluctance (VR) sensor generates an AC sine wave as notched crank reluctor teeth sweep past its magnet, whereas a 3-wire Hall-effect or magneto-resistive sensor switches a sharp `0–5 V` or `0–12 V` square wave. Missing pulses, thermal open coils, oil-wicked connectors, or bent tone-wheel teeth interrupt crank synchronization and log `P0335`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Scanner Cranking Symptom | 0 RPM (no spark / no injector pulse) | Primary RPM/TDC loss prevents PCM ignition & injection synchronization |
| 2-Wire VR Coil Spec / 3-Wire Hall | ~300–1,500 Ω VR | 5 V or 12 V Hall | Check supply + ground on 3-wire Hall; check ohms & AC pulse on 2-wire VR |
| Mechanical Failure Checks | Oil-soaked crank plug & reluctor teeth | Front crank seal oil leaks and chipped tone-wheel teeth mimic bad sensors |

## Commonly Affected Models & Service Bulletins
- Nissan Altima / Maxima / Pathfinder VQ & QR engines (hot-stall CKP sensors)
- Mercedes-Benz / BMW / Volkswagen / Audi (bellhousing VR & Hall CKP failures)
- Chevrolet / Dodge / Jeep / Honda / Hyundai models (crank pulley harness & CKP faults)

## Common Symptoms
- Engine **cranks briskly but will NOT start** with **`0 RPM` on live scanner** and dead tachometer needle
- Sudden mid-drive stall (often returning after 15–30 minutes cool-down when a failing CKP coil thermally opens)
- No ignition spark, no fuel-injector pulse, and extended cranking before delayed backup cam-sensor start on select platforms

## Most Likely Root Causes
- Failed **Crankshaft Position (CKP) sensor** failing thermally when hot or measuring outside `~300–1,500 Ω` (2-wire VR) / dropping square wave (3-wire Hall)
- **Oil-soaked, heat-brittle wiring harness or melted connector** routed beside the crank pulley or exhaust manifold
- **Damaged, rusted, or chipped crankshaft reluctor tone-ring teeth** (or excessive axial crank thrust play)
- Missing **`5 V` / `12 V` supply or ground** (3-wire Hall sensor) or loose sensor mounting bolt altering air gap

## Tools & Parts Reference
- OBD-II live-data scanner (monitoring cranking **Engine RPM**)
- Digital multimeter / lab oscilloscope (`300–1,500 Ω` VR or `5 V/12 V` Hall pulse test)
- Inspection mirror / borescope & electrical contact cleaner

## Step-by-Step Troubleshooting & Fix
1. Disconnect battery negative if working near the starter or crank pulley, clean oil buildup off the CKP plug with electrical contact cleaner, and fix any oil leak dripping onto the harness.
2. Repair rubbed, heat-hardened, or oil-degraded wires using shielded/sealed splices routed clear of pulleys and belts.
3. If `5 V`/`12 V` power and ground test good (or 2-wire VR coil opens when heated/outside `~300–1,500 Ω`), install an **OEM-grade CKP sensor** with a new O-ring and torque bolt accurately to protect air gap.
4. Inspect reluctor tone ring through the sensor bore if needed, clear `P0335`, perform any OEM **Crankshaft Position Variation Relearn**, and verify crisp startup.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $30–$140 | $190–$460 |
| GBP | £25–£110 | £150–£360 |
| CAD | CA$40–CA$185 | CA$250–CA$600 |
| EUR | €28–€130 | €175–€420 |
| CHF | CHF 35–CHF 160 | CHF 225–CHF 520 |

## Frequently Asked Questions
### Why does my car stall when hot and restart 20 minutes later with P0335?
Failing crankshaft sensor windings expand with engine block heat and go open circuit (`OL`), cutting spark and fuel instantly; once cooled, copper contact closes briefly until permanently failing.

### Is it safe to drive with code P0335?
No—`P0335` can shut down ignition and fuel injection instantaneously at highway speeds, causing loss of power steering assist and brake vacuum booster reserve.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
