FaultCodes.org
P0340OBD-IIIgnition & Misfire SystemVerified Guide· Updated: Nov 22, 2026

OBD-II P0340: Camshaft Position Sensor "A" Circuit (Bank 1)

Missing or erratic Bank 1 Intake Camshaft Position (CMP) signal (3-wire 5V/12V Hall-effect square wave or 2-wire VR AC pulse), causing extended cranking, stalling, or no-start—test `5 V / 12 V` reference + ground + signal continuity, clean metallic debris off sensor tip, and inspect timing belt/chain slack.

Quick AnswerHigh — Service Soon

Code P0340 (SAE J2012) means the PCM lost or received an erratic electrical signal from the Bank 1 Camshaft Position Sensor "A" (`CMP` / intake cam). Because the ECU relies on the CMP pulse paired with Crankshaft (CKP) sync to time sequential fuel injection and coil firing, P0340 causes long extended cranking (`3–6 s` before firing), sudden stalling, limp mode, or a complete crank/no-start. Do not buy an aftermarket sensor blindly—first test `5 V / 12 V` reference power, sensor ground, and signal continuity at the plug, pull the sensor to wipe iron filings / metallic debris off its magnetic tip, and inspect for stretched timing chain or jumped timing belt slack (also verify battery/starter cranking RPM and alternator AC ripple) ($35–$140 DIY; $160–$480 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$160 – $480

What This Fault Code Means

While the crankshaft turns twice for every single camshaft rotation, the CMP sensor identifies exactly which stroke Cylinder #1 is on (compression vs exhaust). Most modern engines use a 3-wire Hall-effect CMP (5 V or 12 V supply, ground, and 0–5 V square-wave signal); older designs use a 2-wire Variable Reluctance (VR) pickup generating AC sine pulses. Missing edges, shorted reference voltage, or phase mismatch from a loose timing drive immediately logs P0340.

Common Symptoms

  • Extended cranking (`3–6 seconds`) before catching (as the PCM falls back to crankshaft-only guessing) or crank/no-start
  • Sudden stalling at traffic lights, rough running, and Check Engine Light (P0340)
  • Engine drops into safe limp mode with disabled VVT control and flat acceleration

Most Likely Root Causes

  • Failed Hall-effect (`3-wire`) or VR (`2-wire`) Camshaft Position Sensor "A" dropping signal when heat-soaked (#1 cause)
  • Broken `5 V / 12 V` reference, ground, or signal wire, oil-wicked harness plug, or metallic sludge debris stuck to the magnetic sensor tip
  • Stretched timing chain, skipped timing belt tooth, or failing VVT phaser shifting cam-to-crank alignment out of window
  • Weak battery / slow starter cranking voltage or failed alternator diode AC ripple inducing electrical noise onto CMP wiring (classic Chrysler/Ford/GM quirk)

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
3-Wire Hall-Effect Signal

Check toggling edge during cranking with multimeter or oscilloscope

5 V / 12 V supply + ground + 0–5 V square wave
2-Wire VR Pickup Spec

Variable reluctance pickups generate alternating current proportional to RPM

~200–1,200 Ω coil + AC mV/V crank pulse
Key Mechanical Check

Iron filings distort magnetic teeth; stretched chains shift cam sync

Metallic debris on tip / timing chain slack
Drivability / Safety Risk

Do not drive highway distances until resolved

Sudden stalling or crank / no-start hazard

Commonly Affected Models & Service Bulletins

  • Nissan Altima / Maxima / 350Z / Pathfinder VQ35DE & QR25DE (classic Hall CMP failures)
  • Volkswagen / Audi / BMW / Mercedes-Benz 4- and 6-Cylinder Engines
  • Ford F-150 / Mustang (alternator diode ripple & timing), Chevrolet & Honda/Toyota Models

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Scan live Cranking RPM & Cam/Crank Sync while cranking: verify strong battery voltage (≥ 10.5 V cranking) and inspect the CMP connector for oil intrusion inside the plug or broken locking tabs.
  2. 2On a 3-wire Hall-effect CMP, backprobe or test Key-On harness pins: confirm clean `5 V` (or `12 V` OEM) supply and < 0.5 Ω sensor ground, then watch the signal wire toggle cleanly (0 V <-> 5 V square wave) while cranking (on a 2-wire VR sensor, check coil resistance ~200–1,200 Ω and AC voltage pulse while cranking).
  3. 3Unbolt the CMP sensor to inspect for metallic fuzz/iron particles stuck to the magnet (wiping clean may reveal internal wear!) and check timing belt/chain tension if the waveform looks clean yet out-of-phase with the crankshaft.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

At the unplugged 3-wire CMP connector with Key ON, are `5 V / 12 V` reference power or sensor ground missing?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Digital multimeter or lab oscilloscope (testing 5 V / 12 V Hall square wave or VR AC pulse)OBD-II live scanner (verifying cranking RPM, cam/crank sync & paired timing codes)10 mm socket + lint-free rag (inspecting/cleaning metallic particles on sensor tip)
  1. 1If metallic shavings coat the CMP tip, clean it carefully and inspect engine oil/filter for bearing or timing-guide wear; clean any engine oil out of the connector plug.
  2. 2If 5 V / 12 V supply or ground fails, repair chafed harness wiring or replace a corroded pigtail connector before touching the sensor.
  3. 3If reference voltage and ground test perfect yet signal flatlines during cranking/heat-soak, fit a genuine OEM Camshaft Position Sensor (aftermarket CMP sensors frequently exhibit weak Hall triggers and repeat P0340!).
  4. 4If P0340 returns immediately with a fresh OEM sensor and clean wiring, pull the valve cover or inspect timing marks—replace a stretched timing chain, worn tensioner, or slipped timing belt and clear P0340.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$35 – $140
Professional Repair (Parts + Labor)$160 – $480

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does my car crank for several seconds before finally starting with P0340?

Without the Camshaft Position Sensor signal, the PCM knows crankshaft speed yet cannot tell which cylinder is on compression vs exhaust stroke. After 3–6 seconds of cranking, the ECU makes an educated backup guess from the crankshaft sensor alone so the car starts slowly.

Why do mechanics recommend ONLY genuine OEM Camshaft Position Sensors for P0340?

Many generic aftermarket CMP sensors have slower Hall-effect rise times or loose air-gap tolerances that fail high-RPM sync or heat-soak within weeks, causing P0340 to come right back even on a brand-new part.

Related Searches & Questions

OBD2 P0340 camshaft position sensor A bank 1 fixP0340 extended cranking no start test 5V Hall sensorP0340 metallic debris on sensor tip timing chainNissan Chevy VW BMW P0340 OEM sensor

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0340: Camshaft Position Sensor "A" Circuit (Bank 1) | FaultCodes.org