FaultCodes.org
U0100OBD-IICAN Bus & Network CommunicationVerified Guide· Updated: Nov 22, 2026

OBD-II U0100: Lost Communication With ECM/PCM "A" (CAN Bus Timeout)

Critical SAE J2012 network fault—CAN-H / CAN-L bus nodes lost the ECM/PCM heartbeat; check battery voltage (`≥ 12.6 V` KOEO) and ECM main fuses/relays FIRST, then (with battery disconnected) measure OBD-II Pin 6 (CAN-H) to Pin 14 (CAN-L) = `60 Ω` normal (120 Ω open leg, 0 Ω shorted bus).

Quick AnswerCritical — Stop Immediately

Code U0100 (SAE J2012) means other vehicle controllers (TCM, ABS/ESC, Instrument Cluster, or BCM) stopped receiving periodic CAN-bus heartbeat messages from the Engine Control Module (ECM/PCM "A"), commonly triggering a no-crank / no-start, immobilized gauges, or sudden shutdown—do not drive. Always check battery state (`≥ 12.6 V` KOEO) and ECM main power / ignition fuses and relays FIRST (a dead ECM cannot transmit on CAN). Next, disconnect the 12V negative battery cable, wait 2 minutes, and measure CAN bus resistance across OBD-II Pin 6 (CAN-H) and Pin 14 (CAN-L): `~60 Ω` confirms intact bus termination (two parallel 120 Ω resistors), whereas `120 Ω` proves an open bus leg and `~0 Ω` signals a shorted CAN bus requiring module isolation ($20–$220 DIY fuse/relay/battery checks; $180–$1,250 professional bus wiring or ECM repair).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
CAN Bus & Network Communication
Professional Repair
$180 – $1,250

What This Fault Code Means

High-speed powertrain CAN (ISO 15765-4, 500 kbps) links the ECM, TCM, ABS, and gateway across twisted-pair CAN-H (Pin 6) and CAN-L (Pin 14) wires terminated at each end by two 120 Ω resistors in parallel (60 Ω total). If the ECM loses battery/ignition/ground power, a module shorts CAN-H to CAN-L (0 Ω), or one twisted leg breaks (120 Ω), all peer modules store U0100.

Common Symptoms

  • Engine no-crank or cranks-no-start with "No Communication" when scanning the Engine/ECM module
  • Warning lights across dash (ABS, Traction, Security/Immobilizer), dropped tachometer/speedometer, or cooling fans roaring at full blast KOEO
  • Stalling or transmission stuck in Park / limp gear alongside multiple U-codes (U0100, U0101, U0121)

Most Likely Root Causes

  • Weak/discharged 12V battery (`< 12.6 V` KOEO), corroded battery terminals, or blown ECM main fuse / failed ECM main relay (#1 overlooked root cause!)
  • Corroded or broken ECM ground strap / power feed leaving the ECM unpowered despite good fuses
  • Shorted or broken CAN-H / CAN-L twisted-pair wiring (chafed engine harness, rodent damage, or water in splice connectors—120 Ω open or 0 Ω short)
  • Water-damaged ABS/TCM/gateway module dragging down the shared CAN bus, or rare internal ECM/PCM failure

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
First-Check Power Baseline

Always rule out low voltage, blown ECM fuse, or bad relay before bus probing

≥ 12.6 V KOEO + ECM fuses/relays
CAN-H (Pin 6) to CAN-L (Pin 14)

Two parallel 120 Ω terminators; 120 Ω = open leg, 0 Ω = shorted bus

60 Ω normal (battery disconnected)
Physical Bus Layer

Maintain twisted-pair pitch when splicing damaged CAN-H / CAN-L wires

ISO 15765-4 High-Speed CAN (500 kbps)

Commonly Affected Models & Service Bulletins

  • Chevrolet Silverado / Equinox / Nissan Altima / Rogue (ECM relay, IPDM & CAN splice faults)
  • Ford F-150 / Focus / Dodge Charger / Ram (TIPM/BCM relays, under-battery harness & CAN bus)
  • Volkswagen / Audi / BMW / Mercedes-Benz & Toyota / Honda (gateway/CAN wiring & ECM water intrusion)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Test battery resting voltage (`≥ 12.6 V` KOEO) and inspect battery clamps; then check ALL ECM/PCM main power, ignition, and EFI fuses/relays in the under-hood PDC (swap an identical non-critical relay like horn/AC to test relay operation).
  2. 2Disconnect the 12V battery negative cable completely, wait 2 minutes for bus sleep, and measure resistance between OBD-II Pin 6 (CAN-H) and Pin 14 (CAN-L) with an ohmmeter: `~60 Ω` = both 120 Ω terminators healthy; `~120 Ω` = open CAN leg/disconnected terminator; `~0 Ω` or `< 50 Ω` = CAN-H/CAN-L short (check Pin 6 & Pin 14 to ground too).
  3. 3If CAN bus resistance reads abnormal (120 Ω or 0 Ω), unplug CAN star-connector blocks or suspect modules (ABS, TCM, aftermarket OBD trackers) one by one until 60 Ω returns; if bus reads 60 Ω yet ECM still refuses communication, load-test all ECM power & ground pins right at the ECM plug before condemning the ECM.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is resting battery voltage < 12.6 V KOEO, or is an ECM main fuse / ECM relay / engine ground strap blown, dead, or corroded?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

All-module OBD-II diagnostic scanner (scanning ECM, TCM, ABS & BCM topology)Digital multimeter & test load bulb (for ≥ 12.6 V, 60 Ω Pin 6–14 test & ECM power/ground load testing)Dual-channel oscilloscope (optional for CAN-H / CAN-L voltage mirrors) & wiring schematics
  1. 1Charge/replace a failing 12V battery (`< 12.6 V`), clean corroded terminals/body ground straps, and replace any blown ECM fuse or faulty ECM main relay.
  2. 2Remove any faulty aftermarket GPS/OBD-II plug-in dongles or remote starters spliced into the CAN harness if unplugging them restores bus health.
  3. 3If Pin 6–14 measured 120 Ω or 0 Ω, trace and splice broken/shorted CAN-H / CAN-L twisted pairs (maintain tight twist pitch!) or replace water-intruded bus splice blocks / shorted peer modules.
  4. 4Only after proving clean 60 Ω termination AND verified load-tested ECM powers & grounds at the ECM connector, have a qualified technician repair/replace and program/VIN-code the ECM/PCM, then clear all U0100 codes.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$20 – $220
Professional Repair (Parts + Labor)$180 – $1,250

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: U0100 (CAN Bus & Network Communication)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $180 – $1,250

Frequently Asked Questions

Why should I measure Pin 6 to Pin 14 with the battery disconnected for U0100?

Ohmmeters inject small test voltages that get corrupted by active CAN data traffic (~2.5 V resting bus bias). Disconnecting the 12V battery powers down all transceivers so you get a pure measurement of the two parallel 120 Ω bus resistors (`60 Ω` healthy).

Does U0100 automatically mean my engine computer (ECM) is fried?

No! Most U0100 cases stem from a blown ECM main relay/fuse, weak 12V battery, corroded engine ground strap, or chafed CAN wiring—replacing an ECM without testing powers, grounds, and 60 Ω bus resistance wastes $1,000+.

Related Searches & Questions

OBD2 U0100 lost communication with ECM PCM fixU0100 OBD2 pin 6 pin 14 60 ohms vs 120 ohmsU0100 fuse relay ground no crank no startcan you drive with U0100 code

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II U0100: Lost Communication With ECM/PCM "A" (CAN Bus Timeout) | FaultCodes.org