# OBD-II U0100: OBD-II U0100: Lost Communication With ECM/PCM "A" (CAN Bus Timeout)

> **Quick Answer:** Code **U0100** (SAE J2012) means other vehicle controllers (TCM, ABS/ESC, Instrument Cluster, or BCM) stopped receiving periodic **CAN-bus heartbeat messages from the Engine Control Module (ECM/PCM "A")**, commonly triggering a **no-crank / no-start**, immobilized gauges, or sudden shutdown—**do not drive**. Always check **battery state (`≥ 12.6 V` KOEO)** and **ECM main power / ignition fuses and relays FIRST** (a dead ECM cannot transmit on CAN). Next, **disconnect the 12V negative battery cable**, wait 2 minutes, and measure **CAN bus resistance across OBD-II Pin 6 (CAN-H) and Pin 14 (CAN-L)**: **`~60 Ω`** confirms intact bus termination (two parallel `120 Ω` resistors), whereas **`120 Ω`** proves an open bus leg and **`~0 Ω`** signals a shorted CAN bus requiring module isolation ($20–$220 DIY fuse/relay/battery checks; $180–$1,250 professional bus wiring or ECM repair).

- **URL:** https://faultcodes.org/automotive/obd2-u0100
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** CAN Bus & Network Communication
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Professional Recommended
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
High-speed powertrain CAN (`ISO 15765-4`, `500 kbps`) links the ECM, TCM, ABS, and gateway across twisted-pair **CAN-H (Pin 6)** and **CAN-L (Pin 14)** wires terminated at each end by two `120 Ω` resistors in parallel (`60 Ω` total). If the ECM loses battery/ignition/ground power, a module shorts CAN-H to CAN-L (`0 Ω`), or one twisted leg breaks (`120 Ω`), all peer modules store `U0100`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| First-Check Power Baseline | ≥ 12.6 V KOEO + ECM fuses/relays | Always rule out low voltage, blown ECM fuse, or bad relay before bus probing |
| CAN-H (Pin 6) to CAN-L (Pin 14) | 60 Ω normal (battery disconnected) | Two parallel 120 Ω terminators; 120 Ω = open leg, 0 Ω = shorted bus |
| Physical Bus Layer | ISO 15765-4 High-Speed CAN (500 kbps) | Maintain twisted-pair pitch when splicing damaged CAN-H / CAN-L wires |

## Commonly Affected Models & Service Bulletins
- Chevrolet Silverado / Equinox / Nissan Altima / Rogue (ECM relay, IPDM & CAN splice faults)
- Ford F-150 / Focus / Dodge Charger / Ram (TIPM/BCM relays, under-battery harness & CAN bus)
- Volkswagen / Audi / BMW / Mercedes-Benz & Toyota / Honda (gateway/CAN wiring & ECM water intrusion)

## Common Symptoms
- Engine **no-crank or cranks-no-start** with "No Communication" when scanning the Engine/ECM module
- Warning lights across dash (`ABS`, `Traction`, `Security/Immobilizer`), dropped tachometer/speedometer, or cooling fans roaring at full blast KOEO
- Stalling or transmission stuck in Park / limp gear alongside multiple `U-codes` (`U0100`, `U0101`, `U0121`)

## Most Likely Root Causes
- **Weak/discharged 12V battery (`< 12.6 V` KOEO)**, corroded battery terminals, or **blown ECM main fuse / failed ECM main relay** (#1 overlooked root cause!)
- **Corroded or broken ECM ground strap / power feed** leaving the ECM unpowered despite good fuses
- **Shorted or broken CAN-H / CAN-L twisted-pair wiring** (chafed engine harness, rodent damage, or water in splice connectors—`120 Ω` open or `0 Ω` short)
- Water-damaged **ABS/TCM/gateway module** dragging down the shared CAN bus, or rare internal **ECM/PCM failure**

## Tools & Parts Reference
- All-module OBD-II diagnostic scanner (scanning ECM, TCM, ABS & BCM topology)
- Digital multimeter & test load bulb (for `≥ 12.6 V`, `60 Ω` Pin 6–14 test & ECM power/ground load testing)
- Dual-channel oscilloscope (optional for CAN-H / CAN-L voltage mirrors) & wiring schematics

## Step-by-Step Troubleshooting & Fix
1. Charge/replace a failing **12V battery (`< 12.6 V`)**, clean corroded terminals/body ground straps, and replace any blown **ECM fuse or faulty ECM main relay**.
2. Remove any faulty **aftermarket GPS/OBD-II plug-in dongles or remote starters** spliced into the CAN harness if unplugging them restores bus health.
3. If Pin 6–14 measured `120 Ω` or `0 Ω`, trace and splice broken/shorted **CAN-H / CAN-L twisted pairs** (maintain tight twist pitch!) or replace water-intruded bus splice blocks / shorted peer modules.
4. Only after proving clean `60 Ω` termination AND verified load-tested ECM powers & grounds at the ECM connector, have a qualified technician repair/replace and program/VIN-code the **ECM/PCM**, then clear all `U0100` codes.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $20–$220 | $180–$1250 |
| GBP | £15–£175 | £145–£980 |
| CAD | CA$25–CA$290 | CA$240–CA$1620 |
| EUR | €18–€200 | €165–€1150 |
| CHF | CHF 22–CHF 240 | CHF 220–CHF 1450 |

## Frequently Asked Questions
### Why should I measure Pin 6 to Pin 14 with the battery disconnected for U0100?
Ohmmeters inject small test voltages that get corrupted by active CAN data traffic (`~2.5 V` resting bus bias). Disconnecting the 12V battery powers down all transceivers so you get a pure measurement of the two parallel `120 Ω` bus resistors (**`60 Ω`** healthy).

### Does U0100 automatically mean my engine computer (ECM) is fried?
No! Most `U0100` cases stem from a **blown ECM main relay/fuse, weak 12V battery, corroded engine ground strap, or chafed CAN wiring**—replacing an ECM without testing powers, grounds, and `60 Ω` bus resistance wastes $1,000+.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
