FaultCodes.org
P0138OBD-IIFuel Trim & Air/O2 MeteringVerified Guide· Updated: Nov 22, 2026

OBD-II P0138: O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)

Downstream post-catalyst zirconia O2 sensor (B1S2) stays pinned > 0.80–0.90 V continuously—inspect for melted signal wire shorted to 12 V heater power, chronically rich running (P0172), or an internally shorted sensor before swapping parts.

Quick AnswerModerate — Plan Repair

Code P0138 (SAE J2012) means the downstream Bank 1 Sensor 2 (`B1S2`) oxygen sensor signal behind the catalytic converter stayed pinned at high voltage (`> 0.80–0.90 V`, or even `> 1.2–12 V` during a harness short) continuously beyond factory time thresholds. Because B1S2 monitors catalytic oxygen storage rather than fuel delivery, do not buy a new sensor blindly: check live `B1S2` voltage first (reads > 1.1 V or 12 V = signal wire shorted to the `12 V` heater feed on a melted exhaust harness), look for chronically rich codes (`P0172`/`P0175` or leaking injector) flooding the exhaust with zero O2, or confirm an internally shorted downstream zirconia sensor ($45–$160 DIY; $180–$420 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$180 – $420

What This Fault Code Means

A healthy downstream zirconia (ZrO2) O2 sensor generates roughly 0.60–0.75 V steadily at warm cruise (normal range 0.10–0.90 V). If the B1S2 signal wire chafes against the hot exhaust pipe or transmission and shorts to the adjacent 12 V O2 heater wire or 5 V reference—or if chronic rich combustion leaves zero free oxygen downstream—voltage pins above ~0.80–0.90 V continuously and triggers P0138.

Common Symptoms

  • Steady Check Engine Light (P0138) and automatic emissions inspection failure
  • Usually smooth drivability if electrical/sensor-only, OR black exhaust smoke and strong gas smell when paired with P0172
  • Potential blown O2 heater fuse if melted underbody wiring shorts heater 12 V to signal/ground

Most Likely Root Causes

  • `B1S2` signal wire melted or chafed against exhaust/bellhousing, shorting to `12 V` heater power or 5 V reference
  • Internally shorted downstream zirconia O2 sensor (`B1S2`) or coolant/water intrusion inside the underbody connector
  • Chronically rich engine combustion (`P0172`, leaking injector, high fuel pressure, stuck purge valve) consuming all post-cat O2
  • Failed ECM internal O2 signal driver or high-resistance sensor ground circuit shift

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
High Voltage Trigger Window

Normal warm post-cat zirconia reading is ~0.60–0.75 V steady

B1S2 pinned > 0.80–0.90 V continuously
Short-to-Voltage Clues

Zirconia sensors cannot generate > ~1.0 V alone; points to 12V/5V short

Reading > 1.1–1.27 V (or high unplugged)
Unplugged ECM Bias Baseline

Proves ECM input and harness are intact before blaming the sensor

~0.45 V (450 mV) with sensor unplugged KOEO
Sensor Position

Monitors catalyst O2 storage rather than primary air-fuel trim

Bank 1, Post-Catalyst (Sensor 2)

Commonly Affected Models & Service Bulletins

  • Jeep / Dodge / Chrysler / Ram Trucks & SUVs (exhaust-chafed B1S2 pigtail & sensor bias)
  • Toyota / Honda / Nissan Four-Cylinder & V6 Platforms (post-cat zirconia B1S2)
  • Chevrolet / Ford / Volkswagen / BMW Gasoline Models (SAE J2012 / EOBD)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Scan live OBD-II B1S2 voltage KOEO (engine off) and warm idle, and check for companion rich/heater codes (P0172, P0141)—any reading > 1.1 V points directly to a short to voltage, NOT rich running.
  2. 2Raise vehicle safely on jack stands and inspect the post-cat `B1S2` pigtail where it passes near the exhaust pipe, heat shields, and driveshaft for melted insulation or green corroded connector pins.
  3. 3Unplug B1S2 KOEO and watch live scanner voltage: if it stays pinned > 1.0 V unplugged, the vehicle harness is shorted to `12 V` / `5 V`; if voltage drops to ECM bias (~0.45 V) unplugged and combustion trims are normal, the sensor itself is shorted.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does live scan data show B1S2 above ~1.1–1.27 V (or stay high even with the sensor unplugged KOEO)?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data scanner (B1S2 voltage, fuel trims, KOEO unplugged check)22 mm (7/8 in) slotted oxygen sensor offset socket & penetrating oilDigital multimeter & heat-shrink wiring repair sleeves
  1. 1Repair any melted or pinched Bank 1 Sensor 2 wiring harness sections with heat-shrink butt splices, dielectric grease, and heat-reflective sleeving routed safely clear of the exhaust.
  2. 2If P0172 or negative fuel trims accompany P0138, fix the root rich fault (leaking injector, high fuel pressure, MAF, or EVAP purge) first.
  3. 3Unthread the old downstream B1S2 sensor (using a 22 mm O2 offset socket and penetrating oil), thread in an OEM-grade zirconia O2 sensor with anti-seize only on outer threads, and clip the harness securely.
  4. 4Clear P0138 and drive a warm steady cruise while verifying B1S2 settles cleanly around 0.60–0.75 V.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$45 – $160
Professional Repair (Parts + Labor)$180 – $420

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Where is Bank 1 Sensor 2 located on my vehicle?

Bank 1 is the cylinder side containing cylinder #1, and Sensor 2 is always the downstream sensor mounted behind (after) the Bank 1 catalytic converter—often accessible from underneath the car.

Can a melted wire on the O2 sensor cause P0138?

Yes—very often. When the B1S2 harness comes unclipped and touches the hot exhaust pipe, the 12 V heater wire melts directly into the O2 signal wire, pinning B1S2 above 0.90–1.27 V and setting P0138.

Related Searches & Questions

OBD2 P0138 O2 sensor bank 1 sensor 2 high voltage fixP0138 melted wiring 12V heater short vs bad sensorP0138 bank 1 sensor 2 location after catP0138 repair cost DIY O2 sensor

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0138: O2 Sensor Circuit High Voltage (Bank 1 Sensor 2) | FaultCodes.org