# OBD-II P0138: OBD-II P0138: O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)

> **Quick Answer:** Code **P0138** (SAE J2012) means the downstream **Bank 1 Sensor 2 (`B1S2`)** oxygen sensor signal behind the catalytic converter stayed pinned at **high voltage (`> 0.80–0.90 V`, or even `> 1.2–12 V` during a harness short)** continuously beyond factory time thresholds. Because `B1S2` monitors catalytic oxygen storage rather than fuel delivery, **do not buy a new sensor blindly**: check **live `B1S2` voltage first** (reads `> 1.1 V` or `12 V` = signal wire shorted to the **`12 V` heater feed** on a melted exhaust harness), look for **chronically rich codes (`P0172`/`P0175` or leaking injector)** flooding the exhaust with zero O2, or confirm an internally shorted downstream zirconia sensor ($45–$160 DIY; $180–$420 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0138
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Fuel Trim & Air/O2 Metering
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** Yes (Short Term)
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
A healthy downstream zirconia (`ZrO2`) O2 sensor generates roughly `0.60–0.75 V` steadily at warm cruise (normal range `0.10–0.90 V`). If the `B1S2` signal wire chafes against the hot exhaust pipe or transmission and shorts to the adjacent `12 V` O2 heater wire or `5 V` reference—or if chronic rich combustion leaves zero free oxygen downstream—voltage pins above `~0.80–0.90 V` continuously and triggers `P0138`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| High Voltage Trigger Window | B1S2 pinned > 0.80–0.90 V continuously | Normal warm post-cat zirconia reading is ~0.60–0.75 V steady |
| Short-to-Voltage Clues | Reading > 1.1–1.27 V (or high unplugged) | Zirconia sensors cannot generate > ~1.0 V alone; points to 12V/5V short |
| Unplugged ECM Bias Baseline | ~0.45 V (450 mV) with sensor unplugged KOEO | Proves ECM input and harness are intact before blaming the sensor |
| Sensor Position | Bank 1, Post-Catalyst (Sensor 2) | Monitors catalyst O2 storage rather than primary air-fuel trim |

## Commonly Affected Models & Service Bulletins
- Jeep / Dodge / Chrysler / Ram Trucks & SUVs (exhaust-chafed B1S2 pigtail & sensor bias)
- Toyota / Honda / Nissan Four-Cylinder & V6 Platforms (post-cat zirconia B1S2)
- Chevrolet / Ford / Volkswagen / BMW Gasoline Models (SAE J2012 / EOBD)

## Common Symptoms
- Steady Check Engine Light (`P0138`) and automatic emissions inspection failure
- Usually smooth drivability if electrical/sensor-only, OR black exhaust smoke and strong gas smell when paired with `P0172`
- Potential blown O2 heater fuse if melted underbody wiring shorts heater `12 V` to signal/ground

## Most Likely Root Causes
- **`B1S2` signal wire melted or chafed against exhaust/bellhousing**, shorting to **`12 V` heater power** or `5 V` reference
- **Internally shorted downstream zirconia O2 sensor (`B1S2`)** or coolant/water intrusion inside the underbody connector
- Chronically **rich engine combustion (`P0172`, leaking injector, high fuel pressure, stuck purge valve)** consuming all post-cat O2
- Failed ECM internal O2 signal driver or high-resistance sensor ground circuit shift

## Tools & Parts Reference
- OBD-II live-data scanner (`B1S2` voltage, fuel trims, KOEO unplugged check)
- 22 mm (7/8 in) slotted oxygen sensor offset socket & penetrating oil
- Digital multimeter & heat-shrink wiring repair sleeves

## Step-by-Step Troubleshooting & Fix
1. Repair any melted or pinched **Bank 1 Sensor 2 wiring harness** sections with heat-shrink butt splices, dielectric grease, and heat-reflective sleeving routed safely clear of the exhaust.
2. If `P0172` or negative fuel trims accompany `P0138`, fix the root rich fault (leaking injector, high fuel pressure, MAF, or EVAP purge) first.
3. Unthread the old downstream `B1S2` sensor (using a `22 mm` O2 offset socket and penetrating oil), thread in an **OEM-grade zirconia O2 sensor** with anti-seize only on outer threads, and clip the harness securely.
4. Clear `P0138` and drive a warm steady cruise while verifying `B1S2` settles cleanly around `0.60–0.75 V`.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $45–$160 | $180–$420 |
| GBP | £38–£130 | £145–£330 |
| CAD | CA$60–CA$210 | CA$235–CA$545 |
| EUR | €42–€145 | €165–€380 |
| CHF | CHF 50–CHF 175 | CHF 215–CHF 475 |

## Frequently Asked Questions
### Where is Bank 1 Sensor 2 located on my vehicle?
Bank 1 is the cylinder side containing cylinder #1, and **Sensor 2** is always the **downstream sensor mounted behind (after) the Bank 1 catalytic converter**—often accessible from underneath the car.

### Can a melted wire on the O2 sensor cause P0138?
Yes—very often. When the `B1S2` harness comes unclipped and touches the hot exhaust pipe, the `12 V` heater wire melts directly into the O2 signal wire, pinning `B1S2` above `0.90–1.27 V` and setting `P0138`.


## Verified Official & Engineering References
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
