FaultCodes.org
P0118OBD-IIEngine Cooling & ThermostatVerified Guide· Updated: Nov 22, 2026

OBD-II P0118: Engine Coolant Temperature (ECT) Circuit High Input

NTC thermistor signal pulled `≥ 4.6 V` (open circuit / infinite resistance), defaulting PCM coolant temp to `-40 °C (-40 °F)`—causes hard cold starts, over-rich fueling & cooling fans locked ON; inspect unplugged/corroded pins and test the ohm curve (`~2–3 kΩ @ 20 °C` -> `~200–300 Ω @ 90 °C`).

Quick AnswerHigh — Service Soon

Code P0118 (SAE J2012) means the PCM sees `≥ 4.6 V` on the Engine Coolant Temperature (ECT) sensor signal wire—an open circuit or infinite resistance, causing the computer to default to `-40 °C (-40 °F)`. Because the ECM thinks the engine is frozen while also disabling reliable overheating telemetry, it dumps over-rich cold-start fuel (causing hard starts/black smoke) and locks the electric radiator fans ON full speed as a failsafe. Before draining coolant, check whether the 2-pin ECT connector near the thermostat housing came unplugged or corroded, then ohm-test the sensor across temperatures (`~2–3 kΩ @ 20 °C` dropping smoothly to `~200–300 Ω @ 90 °C`) ($25–$85 DIY; $130–$340 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Engine Cooling & Thermostat
Professional Repair
$130 – $340

What This Fault Code Means

Almost all automotive ECT sensors are Negative Temperature Coefficient (NTC) thermistors powered by a 5 V PCM pull-up resistor to sensor ground. Cold coolant creates high resistance (high voltage); hot coolant drops resistance sharply (low voltage). When a wire breaks, a plug sits loose, or the internal thermistor fails open (> 100 kΩ / OL), voltage floats straight to `4.6–5.0 V` (`-40 °C`) and trips P0118.

Common Symptoms

  • Radiator cooling fans running at 100% max speed continuously, even seconds after a cold key-on
  • Hard starting, flooding/over-rich exhaust smell, and black tailpipe smoke because the ECU fuels for -40 °C
  • Instrument cluster temperature gauge pinned dead at cold/bottom (or erratic warning), plus active CEL (P0118)

Most Likely Root Causes

  • Unplugged, loose, or green-corroded 2-pin ECT sensor connector (especially right after thermostat/intake work) (#1 cause)
  • Broken or rodent-chewed `5 V` signal or ground return wire between the sensor and PCM
  • Failed open internal NTC thermistor inside the ECT sensor reading OL / > 50 kΩ warm
  • Severe air pocket in the cooling system or faulty PCM 5 V pull-up circuit (rare)

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
High-Input Fault Threshold

5V pull-up circuit floats high when NTC thermistor or ground opens

≥ 4.6 V signal -> defaults to -40 °C (-40 °F)
NTC Resistance at 20 °C (68 °F)

Check against OEM spec; OL / infinite confirms open thermistor

~2–3 kΩ (2,000–3,000 Ω typical)
NTC Resistance at 90 °C (194 °F)

Negative Temperature Coefficient drops resistance steeply as heat rises

~200–300 Ω (hot operating temp)
Failsafe PCM Response

Protects engine from hidden overheating while hurting cold/hot starts

Radiator fans locked ON + rich fuel trim

Commonly Affected Models & Service Bulletins

  • Volkswagen / Audi (`G62` 2-/4-pin ECT sensor) & BMW Coolant Outlet Sensors
  • Honda Civic / Accord / CR-V & Toyota Camry / Tacoma / Corolla Models
  • Chevrolet Silverado / Cruze / Malibu, Dodge/Jeep & Ford Focus/F-150 Engines

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Plug in an OBD-II scanner Key-On Engine-Off: if Live ECT displays `-40 °C (-40 °F)`, inspect the 2-wire ECT plug on the cylinder head or thermostat housing for pushed-out pins, coolant intrusion, or rodent-chewed harness leads.
  2. 2With the ECT connector unplugged and Key ON, measure across the harness-side pins: expect `~5.0 V` pull-up on the signal wire and good continuity (< 0.5 Ω) on the sensor ground. Briefly jumper the two harness pins with a fused jumper/paperclip—live scan-tool ECT should immediately swing to `+120 °C+` (`P0117`), proving wiring and PCM are healthy.
  3. 3Ohm-test the disconnected ECT sensor pins directly against temperature: a healthy NTC thermistor reads `~2–3 kΩ @ 20 °C (68 °F)` and drops cleanly to `~200–300 Ω @ 90 °C (194 °F)`; OL or unchanging megaohms confirms a dead sensor.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does live OBD-II ECT read `-40 °C (-40 °F)` AND does jumping the 2 harness pins briefly flip scan-tool ECT to `+120 °C+`?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data scanner (checking -40 °C default vs live temp curve)Digital multimeter (kΩ/Ω NTC curve test & 5 V pull-up check) + fused jumper wireDeep metric socket (19 mm typical) + drain pan & OEM coolant for bleeding
  1. 1Clean any green coolant corrosion out of the 2-pin connector, click the locking tab home securely, or splice in a fresh OEM ECT pigtail harness if wires frayed right at the plug.
  2. 2If the harness jumper test flips live ECT from -40 °C to hot (+120 °C+) yet the sensor reads OL or wildly off the 2–3 kΩ @ 20 °C curve, drain slightly below sensor height on a stone-cold engine and fit an OEM ECT sensor with a fresh crush washer/O-ring.
  3. 3Top off with OEM-specified coolant and bleed all trapped air pockets cleanly from the cooling circuit (trapped steam voids cause false spikes and overheating).
  4. 4Clear P0118, confirm electric fans cycle normally only around thermostat/fan-on temperature (~95–105 °C), and verify smooth warm starts.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$25 – $85
Professional Repair (Parts + Labor)$130 – $340

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does P0118 make my cooling fans run nonstop and my car hard to start?

An open ECT circuit pulls the 5 V reference to 4.6–5.0 V, which the PCM decodes as -40 °C (-40 °F). Because the computer loses real engine temperature feedback, it turns the cooling fans on 100% as anti-overheat insurance while commanding heavy cold-start fuel enrichment that floods warm restarts.

Is it safe to drive with OBD-II P0118?

Driving is not recommended beyond short emergency moves: without accurate coolant temperature feedback, you won't see a genuine overheat warning on your gauge, and severe -40 °C over-fueling washes cylinder oil film and risks fouling plugs and catalytic converters.

Related Searches & Questions

OBD2 P0118 ECT circuit high -40 degrees fixP0118 coolant temp sensor ohm test 2 to 3 kOhmP0118 cooling fans stay on hard startHonda VW Chevy Toyota P0118 sensor vs wiring

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0118: Engine Coolant Temperature (ECT) Circuit High Input | FaultCodes.org