# OBD-II P0118: OBD-II P0118: Engine Coolant Temperature (ECT) Circuit High Input

> **Quick Answer:** Code **P0118** (SAE J2012) means the PCM sees **`≥ 4.6 V`** on the **Engine Coolant Temperature (ECT) sensor** signal wire—an **open circuit or infinite resistance**, causing the computer to default to **`-40 °C (-40 °F)`**. Because the ECM thinks the engine is frozen while also disabling reliable overheating telemetry, it dumps **over-rich cold-start fuel** (causing hard starts/black smoke) and locks the **electric radiator fans ON full speed** as a failsafe. Before draining coolant, **check whether the 2-pin ECT connector near the thermostat housing came unplugged or corroded**, then ohm-test the sensor across temperatures (**`~2–3 kΩ @ 20 °C`** dropping smoothly to **`~200–300 Ω @ 90 °C`**) ($25–$85 DIY; $130–$340 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0118
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Engine Cooling & Thermostat
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Almost all automotive ECT sensors are **Negative Temperature Coefficient (NTC)** thermistors powered by a `5 V` PCM pull-up resistor to sensor ground. Cold coolant creates high resistance (high voltage); hot coolant drops resistance sharply (low voltage). When a wire breaks, a plug sits loose, or the internal thermistor fails open (`> 100 kΩ / OL`), voltage floats straight to **`4.6–5.0 V` (`-40 °C`)** and trips `P0118`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| High-Input Fault Threshold | ≥ 4.6 V signal -> defaults to -40 °C (-40 °F) | 5V pull-up circuit floats high when NTC thermistor or ground opens |
| NTC Resistance at 20 °C (68 °F) | ~2–3 kΩ (2,000–3,000 Ω typical) | Check against OEM spec; OL / infinite confirms open thermistor |
| NTC Resistance at 90 °C (194 °F) | ~200–300 Ω (hot operating temp) | Negative Temperature Coefficient drops resistance steeply as heat rises |
| Failsafe PCM Response | Radiator fans locked ON + rich fuel trim | Protects engine from hidden overheating while hurting cold/hot starts |

## Commonly Affected Models & Service Bulletins
- Volkswagen / Audi (`G62` 2-/4-pin ECT sensor) & BMW Coolant Outlet Sensors
- Honda Civic / Accord / CR-V & Toyota Camry / Tacoma / Corolla Models
- Chevrolet Silverado / Cruze / Malibu, Dodge/Jeep & Ford Focus/F-150 Engines

## Common Symptoms
- Radiator cooling fans running at **100% max speed continuously**, even seconds after a cold key-on
- Hard starting, flooding/over-rich exhaust smell, and black tailpipe smoke because the ECU fuels for `-40 °C`
- Instrument cluster temperature gauge pinned dead at cold/bottom (or erratic warning), plus active CEL (`P0118`)

## Most Likely Root Causes
- **Unplugged, loose, or green-corroded 2-pin ECT sensor connector** (especially right after thermostat/intake work) (#1 cause)
- **Broken or rodent-chewed `5 V` signal or ground return wire** between the sensor and PCM
- **Failed open internal NTC thermistor** inside the ECT sensor reading `OL` / `> 50 kΩ` warm
- Severe air pocket in the cooling system or faulty PCM `5 V` pull-up circuit (rare)

## Tools & Parts Reference
- OBD-II live-data scanner (checking `-40 °C` default vs live temp curve)
- Digital multimeter (`kΩ/Ω` NTC curve test & `5 V` pull-up check) + fused jumper wire
- Deep metric socket (`19 mm` typical) + drain pan & OEM coolant for bleeding

## Step-by-Step Troubleshooting & Fix
1. Clean any green coolant corrosion out of the 2-pin connector, click the locking tab home securely, or splice in a fresh OEM **ECT pigtail harness** if wires frayed right at the plug.
2. If the harness jumper test flips live ECT from `-40 °C` to hot (`+120 °C+`) yet the sensor reads `OL` or wildly off the `2–3 kΩ @ 20 °C` curve, drain slightly below sensor height on a **stone-cold engine** and fit an **OEM ECT sensor** with a fresh crush washer/O-ring.
3. Top off with OEM-specified coolant and **bleed all trapped air pockets** cleanly from the cooling circuit (trapped steam voids cause false spikes and overheating).
4. Clear `P0118`, confirm electric fans cycle normally only around thermostat/fan-on temperature (`~95–105 °C`), and verify smooth warm starts.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $25–$85 | $130–$340 |
| GBP | £20–£70 | £100–£270 |
| CAD | CA$35–CA$115 | CA$170–CA$450 |
| EUR | €22–€75 | €115–€310 |
| CHF | CHF 30–CHF 100 | CHF 165–CHF 420 |

## Frequently Asked Questions
### Why does P0118 make my cooling fans run nonstop and my car hard to start?
An open ECT circuit pulls the `5 V` reference to `4.6–5.0 V`, which the PCM decodes as `-40 °C (-40 °F)`. Because the computer loses real engine temperature feedback, it turns the cooling fans on 100% as anti-overheat insurance while commanding heavy cold-start fuel enrichment that floods warm restarts.

### Is it safe to drive with OBD-II P0118?
Driving is **not recommended** beyond short emergency moves: without accurate coolant temperature feedback, you won't see a genuine overheat warning on your gauge, and severe `-40 °C` over-fueling washes cylinder oil film and risks fouling plugs and catalytic converters.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
