FaultCodes.org
P0562OBD-IIPowertrain & Engine ManagementVerified Guide· Updated: Nov 22, 2026

OBD-II P0562: System Voltage Low (Battery / Alternator Charging Fault)

ECM battery/ignition supply dropped below ~10.0–11.0 V—measure KOEO resting voltage (~12.6 V) and running load voltage (13.5–14.5 V @ idle & 2,000 RPM); ALWAYS fix P0562 FIRST because sagging voltage triggers false U0100, P2135, and P0016 codes.

Quick AnswerHigh — Service Soon

Code P0562 (SAE J2012) means the ECM measured system supply voltage falling below `~10.0–11.0 V` for a sustained period—signaling a failing alternator, weak/sulfated battery, slipping serpentine belt, or loose/corroded power & ground cables. ALWAYS diagnose and fix `P0562` FIRST before touching any other stored fault codes: sagging < 11 V bus power routinely triggers phantom `U0100` (lost comm), `P2135` (throttle correlation), and `P0016` (cam/crank correlation) faults across modules! Test directly across battery posts with a multimeter: healthy resting KOEO battery voltage must read `~12.6 V`, and running charging voltage must hold `13.5–14.5 V` both at idle and 2,000 RPM with headlamps + A/C blower ON ($0–$260 DIY; $220–$780 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Powertrain & Engine Management
Professional Repair
$220 – $780

What This Fault Code Means

Automotive ECUs, CAN transceivers, ignition coils, and fuel pumps require stable 12.6–14.5 V DC power. When alternator output drops below electrical demand, battery state of charge drains toward 10–11 V, triggering P0562, dimming lights, dropping electronic power steering/ABS, and stalling the engine once battery reserve exhausts.

Common Symptoms

  • Illuminated Check Engine Light (P0562), red battery warning icon, or dashboard Christmas-tree warnings (ABS, ESP, U0100, P2135)
  • Slow engine cranking, clicking starter solenoid, or dimming headlamps at idle
  • Sudden limp mode, shifting glitches, or complete engine stall while driving once battery reserve drops under ~10 V

Most Likely Root Causes

  • Failing alternator voltage regulator, worn brushes, or blown rectifier diode dropping charging output below 13.5 V under load
  • Loose, sulfated, or corroded battery terminal clamps, broken alternator B+ cable, or oxidized engine-to-chassis ground straps
  • Weak / sulfated 12V battery or excessive parasitic key-off drain dropping cranking/resting voltage under 12.0 V
  • Glazed, loose, or slipping serpentine drive belt or seized automatic belt tensioner (or blown alternator B+ mega-fuse)

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
ECM Low-Voltage Threshold

Triggers P0562 and frequently induces secondary U0100 / P2135 / P0016 faults

< ~10.0–11.0 V sustained supply
Healthy Resting Battery (KOEO)

< 12.2 V indicates discharged or failing sulfated cells

~12.6 V (100% charged 12V battery)
Running Charging Voltage (Loaded)

Test with headlamps + blower ON; also verify AC diode ripple < 0.5 V AC

13.5–14.5 V @ idle & 2,000 RPM
Max Allowable Cable Voltage Drop

Check both B+ positive lead and alternator-housing-to-battery negative path

< 0.3–0.5 V (Alternator to Battery)

Commonly Affected Models & Service Bulletins

  • Chrysler / Dodge / Jeep / Ram Vehicles (alternator voltage regulator & PCM charging faults)
  • Chevrolet / GMC / Ford Trucks & Cars (corroded ground straps, B+ cables & smart-charging alternators)
  • Honda / Toyota / BMW / Volkswagen Platforms (SAE J2012 / EOBD low-voltage protection)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Measure resting battery voltage KOEO directly on the lead battery posts after 15 min rest: `~12.6 V` = full charge; < 12.2 V = discharged/weak battery requiring recharge and load test.
  2. 2Start engine, turn ON high-beam headlamps, rear defroster, and A/C blower, and measure charging voltage at idle and `2,000 RPM`: healthy systems hold `13.5–14.5 V` (under 13.0 V = charging fault; also check AC ripple < 0.5 V AC for bad diodes).
  3. 3Perform a quick voltage drop test from alternator housing to negative battery post AND alternator B+ stud to positive battery post under load (both must measure < 0.3–0.5 V—higher drop condemns corroded terminals, ground straps, or B+ cable).

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is resting battery voltage below 12.2 V, OR are battery terminals/engine ground straps loose, crusty, or corroded?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Digital multimeter (DC resting/loaded volts, AC ripple check, and cable voltage drop)Battery conductance / CCA load tester & wire terminal brushOBD-II scan tool (to clear phantom codes once charging stabilizes)
  1. 1Clean green/white corrosion off battery posts and cable clamps with wire brush & baking-soda solution, tighten terminal nuts firmly, and scrub clean chassis/engine block ground straps.
  2. 2Inspect the serpentine drive belt and automatic belt tensioner for glazing, cracking, or pulley wobble—replace slipped belts immediately.
  3. 3Fully recharge and load-test the 12V battery (swap sulfated batteries failing CCA load tests), and inspect alternator B+ fusible links plus ECM power relay.
  4. 4If belt, wiring drops (< 0.5 V), and battery pass yet running loaded voltage stays below 13.5 V (or AC ripple exceeds 0.5 V), replace the alternator (and clear false phantom U0100/P2135/P0016 codes afterwards).

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0 – $260
Professional Repair (Parts + Labor)$220 – $780

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why should I ALWAYS fix P0562 before troubleshooting U0100, P2135, or P0016?

Low system voltage (< 10–11 V) starves CAN transceivers, dual 5V throttle references, and cam/crank hall sensors simultaneously—causing phantom U0100 (no comm), P2135 (throttle correlation), and P0016 codes that vanish completely once stable 13.5–14.5 V returns.

Is it safe to keep driving with code P0562?

No. Once the alternator stops charging, the car drains the 12V battery rapidly and can unexpectedly lose power steering, ABS, shifting, and engine ignition mid-traffic.

Related Searches & Questions

OBD2 P0562 system voltage low fixP0562 battery vs alternator voltage test 13.5 14.5P0562 causing U0100 P2135 P0016 phantom codesP0562 safe to drive repair cost

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0562: System Voltage Low (Battery /… — Fixes & Cost | FaultCodes.org