# OBD-II P0562: OBD-II P0562: System Voltage Low (Battery / Alternator Charging Fault)

> **Quick Answer:** Code **P0562** (SAE J2012) means the ECM measured system supply voltage falling below **`~10.0–11.0 V`** for a sustained period—signaling a failing alternator, weak/sulfated battery, slipping serpentine belt, or loose/corroded power & ground cables. **ALWAYS diagnose and fix `P0562` FIRST before touching any other stored fault codes**: sagging `< 11 V` bus power routinely triggers phantom **`U0100` (lost comm), `P2135` (throttle correlation), and `P0016` (cam/crank correlation)** faults across modules! Test directly across battery posts with a multimeter: healthy resting KOEO battery voltage must read **`~12.6 V`**, and running charging voltage must hold **`13.5–14.5 V`** both at idle and `2,000 RPM` with headlamps + A/C blower ON ($0–$260 DIY; $220–$780 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0562
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Powertrain & Engine Management
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Automotive ECUs, CAN transceivers, ignition coils, and fuel pumps require stable `12.6–14.5 V` DC power. When alternator output drops below electrical demand, battery state of charge drains toward `10–11 V`, triggering `P0562`, dimming lights, dropping electronic power steering/ABS, and stalling the engine once battery reserve exhausts.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| ECM Low-Voltage Threshold | < ~10.0–11.0 V sustained supply | Triggers P0562 and frequently induces secondary U0100 / P2135 / P0016 faults |
| Healthy Resting Battery (KOEO) | ~12.6 V (100% charged 12V battery) | < 12.2 V indicates discharged or failing sulfated cells |
| Running Charging Voltage (Loaded) | 13.5–14.5 V @ idle & 2,000 RPM | Test with headlamps + blower ON; also verify AC diode ripple < 0.5 V AC |
| Max Allowable Cable Voltage Drop | < 0.3–0.5 V (Alternator to Battery) | Check both B+ positive lead and alternator-housing-to-battery negative path |

## Commonly Affected Models & Service Bulletins
- Chrysler / Dodge / Jeep / Ram Vehicles (alternator voltage regulator & PCM charging faults)
- Chevrolet / GMC / Ford Trucks & Cars (corroded ground straps, B+ cables & smart-charging alternators)
- Honda / Toyota / BMW / Volkswagen Platforms (SAE J2012 / EOBD low-voltage protection)

## Common Symptoms
- Illuminated Check Engine Light (`P0562`), red battery warning icon, or dashboard Christmas-tree warnings (`ABS`, `ESP`, `U0100`, `P2135`)
- Slow engine cranking, clicking starter solenoid, or dimming headlamps at idle
- Sudden limp mode, shifting glitches, or complete engine stall while driving once battery reserve drops under `~10 V`

## Most Likely Root Causes
- **Failing alternator voltage regulator, worn brushes, or blown rectifier diode** dropping charging output below `13.5 V` under load
- **Loose, sulfated, or corroded battery terminal clamps**, broken alternator B+ cable, or oxidized **engine-to-chassis ground straps**
- Weak / sulfated **12V battery** or excessive parasitic key-off drain dropping cranking/resting voltage under `12.0 V`
- Glazed, loose, or slipping **serpentine drive belt** or seized automatic belt tensioner (or blown alternator B+ mega-fuse)

## Tools & Parts Reference
- Digital multimeter (DC resting/loaded volts, AC ripple check, and cable voltage drop)
- Battery conductance / CCA load tester & wire terminal brush
- OBD-II scan tool (to clear phantom codes once charging stabilizes)

## Step-by-Step Troubleshooting & Fix
1. Clean green/white corrosion off battery posts and cable clamps with wire brush & baking-soda solution, tighten terminal nuts firmly, and scrub clean chassis/engine block ground straps.
2. Inspect the **serpentine drive belt** and automatic belt tensioner for glazing, cracking, or pulley wobble—replace slipped belts immediately.
3. Fully recharge and load-test the **12V battery** (swap sulfated batteries failing CCA load tests), and inspect alternator B+ fusible links plus ECM power relay.
4. If belt, wiring drops (`< 0.5 V`), and battery pass yet running loaded voltage stays below `13.5 V` (or AC ripple exceeds `0.5 V`), replace the **alternator** (and clear false phantom `U0100`/`P2135`/`P0016` codes afterwards).

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$260 | $220–$780 |
| GBP | £0–£210 | £175–£610 |
| CAD | CA$0–CA$340 | CA$290–CA$990 |
| EUR | €0–€240 | €195–€690 |
| CHF | CHF 0–CHF 290 | CHF 260–CHF 860 |

## Frequently Asked Questions
### Why should I ALWAYS fix P0562 before troubleshooting U0100, P2135, or P0016?
Low system voltage (`< 10–11 V`) starves CAN transceivers, dual 5V throttle references, and cam/crank hall sensors simultaneously—causing phantom `U0100` (no comm), `P2135` (throttle correlation), and `P0016` codes that vanish completely once stable `13.5–14.5 V` returns.

### Is it safe to keep driving with code P0562?
No. Once the alternator stops charging, the car drains the 12V battery rapidly and can unexpectedly lose power steering, ABS, shifting, and engine ignition mid-traffic.


## Verified Official & Engineering References
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
