FaultCodes.org
P0014OBD-IIPowertrain & Engine ManagementVerified Guide· Updated: Nov 22, 2026

OBD-II P0014: "B" Camshaft Position Timing Over-Advanced or System Performance (Bank 1)

Exhaust ("B") camshaft phaser on Bank 1 stayed over-advanced or lagged behind ECM target—check engine oil level, viscosity, and sludge FIRST, ohm-test the exhaust VVT OCV solenoid (6.0–12.0 Ω @ 20 °C), and inspect clogged oil screens or cam phaser lock pins.

Quick AnswerHigh — Service Soon

Code P0014 (SAE J2012) flags Bank 1 Exhaust ("B") Camshaft Position Timing Over-Advanced or System Performance—meaning the Variable Valve Timing (VVT) exhaust cam phaser failed to track the PCM's commanded angle cleanly. Check engine oil level, oil quality, and correct OEM viscosity FIRST: low oil or thick sludge starves the hydraulic cam phaser immediately and triggers false P0014. Next, unplug and ohm-test the Bank 1 exhaust VVT Oil Control Valve (OCV) solenoid (6.0–12.0 Ω @ 20 °C, OL to housing ground, crisp 12V bench click), clean any clogged VVT oil filter mesh screen, and inspect the exhaust cam phaser lock pin if oil and OCV check out ($35–$145 DIY; $170–$520 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Powertrain & Engine Management
Professional Repair
$170 – $520

What This Fault Code Means

Modern dual-VVT engines adjust exhaust camshaft overlap continuously by routing pressurized engine oil through a PWM-controlled Oil Control Valve (OCV) solenoid into advance/retard chambers inside the exhaust cam phaser ("B"). When sludge jams the OCV spool, an oil screen clogs, or a phaser vane lock pin sticks over-advanced, actual exhaust CMP phase diverges from commanded timing and sets P0014.

Common Symptoms

  • Illuminated Check Engine Light (P0014), rough idle, or stalling when decelerating to stops
  • Sluggish low-end torque, reduced fuel economy, or metallic cold-start rattle from the exhaust cam phaser
  • Companion VVT codes (P0011 intake or P0013 exhaust circuit) if oil neglect affects multiple actuators

Most Likely Root Causes

  • Low, dirty, sludged, or wrong-viscosity engine oil starving hydraulic VVT phaser chambers (#1 cause)
  • Sludge-jammed or sticking Bank 1 exhaust VVT Oil Control Valve (OCV) solenoid
  • Clogged inline VVT oil control filter screen or obstructed cylinder head oil gallery
  • Worn or seized exhaust camshaft phaser lock pin/vanes, stretched timing chain, or noisy exhaust CMP sensor

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
SAE J2012 Camshaft Assignment

Bank 1 contains cylinder #1; "B" denotes exhaust side on DOHC engines

"B" = Bank 1 Exhaust Camshaft
VVT OCV Solenoid Resistance

Test unplugged; also check crisp pintle snap on 12V bench pulse

6.0–12.0 Ω @ 20 °C (OL to housing)
Primary Hydraulic Prerequisite

Sludge, low level, or clogged OCV mesh screens block VVT oil pressure

Clean OEM-viscosity oil & intact filter
Mechanical Phaser Failure Mode

Shows as persistent Desired vs Actual phase delta despite good OCV

Jammed exhaust phaser vane or lock pin

Commonly Affected Models & Service Bulletins

  • GM Ecotec 2.0L / 2.4L & Chevrolet Cruze / Equinox / Malibu (exhaust VVT actuator solenoid)
  • Hyundai / Kia / Toyota / Honda DOHC Dual-VVT Engines (sludged OCV mesh screen & phaser)
  • BMW / Audi / Volkswagen / Volvo Variable Valve Timing Exhaust Camshaft Systems

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Inspect engine oil dipstick level, color, and service history immediately—if oil is >1 quart low, tar-black, or wrong SAE weight, perform an oil/filter service before touching parts.
  2. 2Scan live Exhaust Camshaft Desired vs Actual Angle (Bank 1) while commanding VVT duty cycle (0% -> 50%) via bi-directional scan tool to confirm whether the cam responds sluggishly or stays frozen.
  3. 3Remove the Bank 1 exhaust OCV solenoid: measure coil resistance (6.0–12.0 Ω @ 20 °C), check OL to solenoid body ground, inspect/clean the cylindrical oil filter mesh screen, and bench-pulse briefly with fused 12V to verify crisp pintle snap.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is the engine oil below minimum mark, overdue/sludged, or filled with a collapsed aftermarket oil filter?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II bi-directional scan tool (Desired vs Actual Exhaust Cam Angle Bank 1)Digital multimeter (6.0–12.0 Ω OCV coil & ground isolation check)12V fused jumper leads & brake/parts cleaner (for bench OCV spool & screen inspection)
  1. 1Drain sludged or incorrect-grade oil, install a new OEM oil filter (cheap collapsed aftermarket filters starve VVT heads!), and refill with exact factory-spec synthetic oil.
  2. 2Clean or replace a sticking/out-of-spec Bank 1 exhaust VVT OCV solenoid (6.0–12.0 Ω coil) along with any torn O-rings and clogged VVT oil screen.
  3. 3Test exhaust CMP sensor air gap/signal cleanliness and wiring back to the PCM if live angle telemetry glitches randomly.
  4. 4If fresh oil and a verified OCV still fail to retract an over-advanced phaser (especially with cold-start clatter), replace the exhaust cam phaser sprocket and inspect timing chain tension.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$35 – $145
Professional Repair (Parts + Labor)$170 – $520

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

What is the difference between P0014 and P0011?

Per SAE J2012, "A" (`P0011`) refers to the intake camshaft on Bank 1, whereas "B" (`P0014`) refers specifically to the exhaust camshaft on Bank 1.

Can low oil alone cause P0014 without any mechanical failure?

Yes—very frequently. VVT phasers rely strictly on clean pressurized engine oil to unlock and position the camshaft vanes; running 1–2 quarts low or overdue oil immediately triggers P0014.

Related Searches & Questions

OBD2 P0014 exhaust camshaft timing over-advanced fixP0014 VVT OCV solenoid ohm test 6 to 12 ohmsP0014 vs P0011 intake or exhaust camshaftP0014 oil level sludge cam phaser lock pin

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0014: "B" Camshaft Position Timing… — Fixes & Cost | FaultCodes.org