FaultCodes.org
P0456OBD-IIEVAP Emissions ControlVerified Guide· Updated: Nov 22, 2026

OBD-II P0456: EVAP System Very Small Leak Detected (0.020 in)

CARB/EPA `0.020-inch (0.5 mm)` micro-leak threshold tripped (half the 0.040 in P0442 pinhole)—inspect the gas cap gasket & rusted filler neck lip, check purge valve weep, and pinpoint with a low-pressure EVAP smoke tester (`~0.5–1.0 psi`).

Quick AnswerLow — Minor Issue

Code P0456 (SAE J2012) means the PCM detected a very small EVAP fuel-vapor leak matching or exceeding CARB/EPA's `0.020-inch (0.5 mm)` orifice threshold—literally half the hole size that triggers P0442 (0.040 in). Because a 0.5 mm pinhole is invisible to the naked eye, always inspect and clean the fuel cap rubber gasket and corroded metal filler neck rim first (a tiny grain of grit or rust bubble on the seat causes most P0456 warnings). If a genuine OEM gas cap doesn't clear it, check whether the EVAP purge solenoid is weeping vacuum/pressure slightly and pinpoint the micro-leak cleanly using a regulated EVAP smoke tester (`~0.5–1.0 psi`) ($15–$140 DIY; $110–$410 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$110 – $410

What This Fault Code Means

Federal and California OBD-II regulations require vehicles to detect evaporative fuel vapor leaks down to `0.020 inches (0.5 mm)` in diameter—smaller than a pencil tip. During engine-off or cruise self-tests (using either vacuum decay via the FTP sensor or natural cool-down pressure/ESIM/NVLD pumps), even microscopic hairline cracks in rubber hoses, rusted filler lips, or slightly weeping purge valve seats fail pressure bleed-down and set P0456.

Common Symptoms

  • Check Engine Light (P0456) with zero drivability change, rough running, or power loss
  • Occasionally preceded by a dashboard "Check Gas Cap" alert on Chrysler/Dodge/Jeep/GM models
  • Failed emissions inspection due to active MIL or unready EVAP monitor

Most Likely Root Causes

  • Aged/hardened fuel cap rubber gasket or rust/flaking paint along the filler neck sealing lip (#1 cause)
  • Micro-weeping EVAP purge valve (passing tiny air puffs while closed) or ESIM / NVLD leak-detection pump seal
  • Hairline dry-rot cracks on underbody EVAP rubber couplings or fuel pump lock-ring O-ring atop the fuel tank
  • Pinholes on steel EVAP vapor lines, loose green EVAP service-port cap, or cracked charcoal canister seam

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
CARB / EPA Leak Threshold

Half the diameter of P0442 (0.040 in / 1.0 mm) and one-fourth the area

0.020 inch (0.5 mm) orifice equivalent
Safe EVAP Smoke Pressure

Flowmeter ball reveals micro-leaks even before smoke becomes visible

~0.5–1.0 psi (regulated flowmeter)
Purge Valve Leak Tolerance

Even slight valve seat weep triggers P0456 during monitor decay test

Zero vacuum bleed when unpowered
Required Monitor Fuel Level

Monitor aborts outside range or during heavy sloshing / extreme cold

15%–85% full (+ cold soak)

Commonly Affected Models & Service Bulletins

  • Jeep Grand Cherokee / Wrangler, Dodge Charger / Ram & Chrysler Models (ESIM switch & gas cap)
  • BMW 3/5 Series & Mercedes-Benz Models (NVLD pump seals & fuel cap O-rings)
  • Ford F-150 / Explorer (capless filler seal debris), Toyota, Honda & Chevrolet Models

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Unscrew the fuel cap and inspect both the rubber O-ring (for flat spots or hairline splits) and the steel filler neck lip (for rust blisters or grit breaking the 0.5 mm seal); wipe clean and verify firm tightening.
  2. 2Test the purge valve in the engine bay: unplug its electrical connector and disconnect the tank-side hose—with engine idling, put a finger or vacuum gauge on the valve port; zero suction should exist (any slight weep causes P0456).
  3. 3Close the canister vent valve (via bi-directional scanner or pinch-clamp on the vent hose if applicable) and introduce `~0.5–1.0 psi` regulated EVAP smoke with an LED spotlight to watch for fine wisps around hoses, ESIM/NVLD seals, tank lock ring, or filler neck.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does the fuel cap rubber gasket have flat/cracked rubber OR is the filler neck lip rusted/pitted?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Regulated EVAP smoke tester (`~0.5–1.0 psi`) with flowmeter + bright LED flashlightOBD-II scanner (EVAP vent closure command & FTP pressure monitor)Clean rag + fine Scotch-Brite pad (for cleaning filler neck rust blisters)
  1. 1Sand smooth any flaky rust/paint blisters off the filler neck sealing rim (grease lightly only on threads if needed, keep sealing face clean) and install a genuine OEM gas cap (aftermarket caps frequently fail the 0.020 in check).
  2. 2If the purge solenoid pulls any trace of manifold vacuum when unplugged or fails an 18–30 Ω coil check, replace the EVAP purge valve cleanly.
  3. 3Replace any hairline-cracked rubber EVAP elbow/hose, failed ESIM/NVLD leak detection switch/pump (very common on Chrysler/Dodge/Ram/BMW), or cracked fuel-pump module O-ring spotted under smoke.
  4. 4Clear P0456 and drive with fuel tank 15%–85% full through a cold-soak cycle so the PCM confirms leak-free EVAP readiness.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$15 – $140
Professional Repair (Parts + Labor)$110 – $410

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

What is the exact difference between P0442 and P0456?

Both are EVAP vapor leaks—`P0442` catches a small leak (`0.040 in / 1.0 mm`), whereas `P0456` catches a very small micro-leak (`0.020 in / 0.5 mm`), which is often too tiny to smell and almost always requires an EVAP smoke machine or OEM gas cap swap to locate.

Why do aftermarket gas caps often keep P0456 returning?

Generic locking or universal parts-store caps frequently use looser spring tension and slightly harder rubber compounds that hold 0.040 in (P0442) yet leak past the ultra-strict `0.020 in` (P0456) threshold. Always fit an OEM dealer gas cap.

Related Searches & Questions

OBD2 P0456 very small EVAP leak 0.020 inchP0456 gas cap vs ESIM leak detection pumpP0456 how to find 0.5 mm EVAP leak smoke testJeep Dodge Ram Chrysler BMW P0456 fix

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0456: EVAP System Very Small Leak Detected (0.020 in) | FaultCodes.org