# OBD-II P0456: OBD-II P0456: EVAP System Very Small Leak Detected (0.020 in)

> **Quick Answer:** Code **P0456** (SAE J2012) means the PCM detected a **very small EVAP fuel-vapor leak** matching or exceeding CARB/EPA's **`0.020-inch (0.5 mm)` orifice threshold**—literally half the hole size that triggers `P0442` (`0.040 in`). Because a `0.5 mm` pinhole is invisible to the naked eye, **always inspect and clean the fuel cap rubber gasket and corroded metal filler neck rim first** (a tiny grain of grit or rust bubble on the seat causes most `P0456` warnings). If a genuine OEM gas cap doesn't clear it, check whether the **EVAP purge solenoid is weeping** vacuum/pressure slightly and pinpoint the micro-leak cleanly using a **regulated EVAP smoke tester (`~0.5–1.0 psi`)** ($15–$140 DIY; $110–$410 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0456
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** EVAP Emissions Control
- **Severity:** Low — Minor Issue
- **Safe to Operate?:** Yes (Short Term)
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Federal and California OBD-II regulations require vehicles to detect evaporative fuel vapor leaks down to **`0.020 inches (0.5 mm)`** in diameter—smaller than a pencil tip. During engine-off or cruise self-tests (using either vacuum decay via the `FTP` sensor or natural cool-down pressure/ESIM/NVLD pumps), even microscopic hairline cracks in rubber hoses, rusted filler lips, or slightly weeping purge valve seats fail pressure bleed-down and set `P0456`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| CARB / EPA Leak Threshold | 0.020 inch (0.5 mm) orifice equivalent | Half the diameter of P0442 (0.040 in / 1.0 mm) and one-fourth the area |
| Safe EVAP Smoke Pressure | ~0.5–1.0 psi (regulated flowmeter) | Flowmeter ball reveals micro-leaks even before smoke becomes visible |
| Purge Valve Leak Tolerance | Zero vacuum bleed when unpowered | Even slight valve seat weep triggers P0456 during monitor decay test |
| Required Monitor Fuel Level | 15%–85% full (+ cold soak) | Monitor aborts outside range or during heavy sloshing / extreme cold |

## Commonly Affected Models & Service Bulletins
- Jeep Grand Cherokee / Wrangler, Dodge Charger / Ram & Chrysler Models (ESIM switch & gas cap)
- BMW 3/5 Series & Mercedes-Benz Models (NVLD pump seals & fuel cap O-rings)
- Ford F-150 / Explorer (capless filler seal debris), Toyota, Honda & Chevrolet Models

## Common Symptoms
- Check Engine Light (`P0456`) with zero drivability change, rough running, or power loss
- Occasionally preceded by a dashboard *"Check Gas Cap"* alert on Chrysler/Dodge/Jeep/GM models
- Failed emissions inspection due to active MIL or unready EVAP monitor

## Most Likely Root Causes
- **Aged/hardened fuel cap rubber gasket** or **rust/flaking paint along the filler neck sealing lip** (#1 cause)
- Micro-weeping **EVAP purge valve** (passing tiny air puffs while closed) or **ESIM / NVLD leak-detection pump seal**
- Hairline dry-rot cracks on **underbody EVAP rubber couplings** or fuel pump lock-ring O-ring atop the fuel tank
- Pinholes on steel **EVAP vapor lines**, loose green EVAP service-port cap, or cracked charcoal canister seam

## Tools & Parts Reference
- Regulated **EVAP smoke tester (`~0.5–1.0 psi`)** with flowmeter + bright LED flashlight
- OBD-II scanner (EVAP vent closure command & `FTP` pressure monitor)
- Clean rag + fine Scotch-Brite pad (for cleaning filler neck rust blisters)

## Step-by-Step Troubleshooting & Fix
1. Sand smooth any flaky rust/paint blisters off the **filler neck sealing rim** (grease lightly only on threads if needed, keep sealing face clean) and install a **genuine OEM gas cap** (aftermarket caps frequently fail the `0.020 in` check).
2. If the purge solenoid pulls any trace of manifold vacuum when unplugged or fails an `18–30 Ω` coil check, replace the **EVAP purge valve** cleanly.
3. Replace any hairline-cracked **rubber EVAP elbow/hose**, failed **ESIM/NVLD leak detection switch/pump** (very common on Chrysler/Dodge/Ram/BMW), or cracked fuel-pump module O-ring spotted under smoke.
4. Clear `P0456` and drive with fuel tank **15%–85% full** through a cold-soak cycle so the PCM confirms leak-free EVAP readiness.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $15–$140 | $110–$410 |
| GBP | £12–£110 | £90–£330 |
| CAD | CA$20–CA$185 | CA$145–CA$540 |
| EUR | €15–€130 | €95–€370 |
| CHF | CHF 20–CHF 170 | CHF 135–CHF 490 |

## Frequently Asked Questions
### What is the exact difference between P0442 and P0456?
Both are EVAP vapor leaks—**`P0442`** catches a **small leak (`0.040 in / 1.0 mm`)**, whereas **`P0456`** catches a **very small micro-leak (`0.020 in / 0.5 mm`)**, which is often too tiny to smell and almost always requires an EVAP smoke machine or OEM gas cap swap to locate.

### Why do aftermarket gas caps often keep P0456 returning?
Generic locking or universal parts-store caps frequently use looser spring tension and slightly harder rubber compounds that hold `0.040 in` (`P0442`) yet leak past the ultra-strict **`0.020 in`** (`P0456`) threshold. Always fit an OEM dealer gas cap.


## Verified Official & Engineering References
- [California OBD-II 0.020-Inch EVAP Leak Standard (13 CCR § 1968.2)](https://www.law.cornell.edu/regulations/california/13-CCR-1968.2) (Official Support)
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
