FaultCodes.org
P0715OBD-IITransmission & DrivetrainVerified Guide· Updated: Nov 22, 2026

OBD-II P0715: Input/Turbine Shaft Speed Sensor "A" Circuit

SAE J2012 transmission fault when the TCM loses the input/turbine shaft RPM signal, triggering harsh/delayed shifts or 2nd/3rd gear limp mode—inspect ATF level/metal shavings, connector oil wicking, and measure VR coil resistance (`~300–1,200 Ω`) or Hall-effect `5 V / 12 V` reference.

Quick AnswerHigh — Service Soon

Code P0715 (SAE J2012) means the Transmission Control Module (TCM) or PCM lost a valid signal from the Input/Turbine Shaft Speed Sensor (ISS/TSS) "A"—the sensor measuring torque-converter turbine RPM entering the transmission gearset. Without input speed vs output speed correlation, the TCM typically forces 2nd or 3rd gear limp-home mode with harsh slams into Drive/Reverse; limit driving to short distances or have it inspected promptly to prevent clutch pack heat damage. Check ATF fluid level and inspect for metal shavings first, check the external ISS harness/connector for ATF oil wicking or heat damage, and test 2-wire VR sensor coil resistance (`~300–1,200 Ω`) or 3-wire Hall-effect `5 V` / `12 V` supply and ground ($35–$160 DIY for external sensor; $190–$680 shop for external/internal pan-mounted ISS).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Transmission & Drivetrain
Professional Repair
$190 – $680

What This Fault Code Means

Automatic transmissions calculate gear ratio slip and clutch apply timing by comparing Input/Turbine Shaft Speed (`ISS`) against Output Shaft Speed (`OSS`) and Engine RPM. Whether a 2-wire Variable Reluctance coil (~300–1,200 Ω) or 3-wire Hall sensor (5 V/12 V), thermal coil failure, ATF wicking into connector pins, metal clutch debris clinging to the magnetic tip, or broken wiring interrupts the signal and triggers P0715.

Common Symptoms

  • Transmission locks in 2nd or 3rd limp gear and refuses to upshift into overdrive
  • Harsh bangs/slams shifting into Drive or Reverse, delayed gear engagement, or torque converter lockup disabled
  • Live scan data reads 0 RPM on Input/Turbine Speed (`ISS`) while moving, accompanied by P0715 (and occasionally P0717 / P0730)

Most Likely Root Causes

  • Failed Input/Turbine Speed Sensor (`ISS`)—thermally opening coil (≠ ~300–1,200 Ω VR) or failing internal Hall-effect IC
  • ATF oil wicking into the sensor connector, corroded pins, or melted/rubbed harness near the transmission case & exhaust
  • Low/burnt ATF or ferrous metal shavings sticking to the magnetic sensor tip (signaling internal drum/bearing wear)
  • Damaged internal input clutch-drum reluctor teeth or failing internal TCM / lead-frame conductor plate (e.g., Mercedes 722.6 / Ford 6R80)

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Typical Limp-Mode Behavior

TCM defaults to max line pressure & safe middle gear without ISS signal

Locked in 2nd / 3rd gear + harsh shifts
2-Wire VR / 3-Wire Hall Spec

Test harness supply + ground before replacing external or internal ISS

~300–1,200 Ω VR | 5 V / 12 V Hall
Critical Physical Checks

Metal fuzz shorts/distorts magnetic pickup; oil wicking ruins pin signals

ATF wicking & ferrous metal shavings

Commonly Affected Models & Service Bulletins

  • Chrysler / Dodge / Jeep 42RLE & 62TE / Hyundai / Kia (external 2-wire & 3-wire ISS)
  • Ford F-150 / Mustang 6R80 & Mercedes-Benz 722.6/722.9 (internal lead-frame / conductor-plate ISS)
  • Nissan Altima / Sentra CVT & Honda Accord / Civic automatics (input/primary pulley & turbine speed sensors)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Connect an enhanced OBD-II/TCM scanner and monitor live Input/Turbine Speed (`ISS`) vs Engine RPM in Park/Drive: 0 RPM or erratic spikes while Engine RPM spins confirms P0715 signal loss.
  2. 2Check ATF fluid level, color, and smell (burnt smell or sparkly metal flakes on the dipstick/sensor tip indicate internal mechanical debris), then unplug the external ISS connector to inspect for oil wicking or cracked wires.
  3. 3Test the sensor/circuit by design: on 2-wire VR sensors, measure coil resistance (~300–1,200 Ω) across pins and AC voltage pulse in gear; on 3-wire Hall sensors, verify `5 V` or `12 V` supply + ground at the harness and crisp square-wave switching.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does the transmission connector show ATF oil wicking, broken wires, or is the fluid severely low/full of metallic shavings?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II / TCM live-data scanner (Input/Turbine RPM vs Engine RPM)Digital multimeter (300–1,200 Ω VR resistance & 5 V/12 V Hall probe)Drain pan, OEM-spec ATF, electrical contact cleaner & torque wrench
  1. 1Top up low ATF with exact OEM-spec fluid and change dirty fluid/filter if metal debris coated the sensor's magnetic pickup tip.
  2. 2Clean oil-wicked connector terminals with electronics cleaner and repair chafed transmission wiring or leaking O-rings/seals causing fluid wicking.
  3. 3If supply/ground verify good (or 2-wire coil tests out of ~300–1,200 Ω / opens hot), replace the external Input/Turbine Speed Sensor (or internal pan-mounted conductor-plate/lead-frame assembly where integrated) with OEM torque & O-ring.
  4. 4Clear TCM/PCM codes, verify smooth live ISS RPM tracking matching engine speed in Park/Drive, and confirm normal upshifts across all gears.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$35 – $160
Professional Repair (Parts + Labor)$190 – $680

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Can I drive my car with code P0715 in limp mode?

Only briefly at low speeds to reach safety or a repair shop. Driving in 2nd/3rd limp gear at highway RPMs overheats transmission fluid and accelerates clutch-pack wear.

Is the Input Speed Sensor always external and easy to replace?

On many Nissan, Hyundai/Kia, Chrysler, and Honda transmissions it threads externally onto the case (~20 min DIY), whereas designs like Mercedes 722.6 or Ford 6R80 mount the sensors inside the pan on the conductor plate / molded lead frame, raising shop labor.

Related Searches & Questions

OBD2 P0715 input turbine speed sensor circuitP0715 transmission stuck in 2nd 3rd limp modeP0715 input speed sensor resistance ohms 5V 12VP0715 oil in connector metal shavings ATF

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0715: Input/Turbine Shaft Speed Sensor "A" Circuit | FaultCodes.org