# OBD-II P0715: OBD-II P0715: Input/Turbine Shaft Speed Sensor "A" Circuit

> **Quick Answer:** Code **P0715** (SAE J2012) means the Transmission Control Module (TCM) or PCM lost a valid signal from the **Input/Turbine Shaft Speed Sensor (ISS/TSS) "A"**—the sensor measuring torque-converter turbine RPM entering the transmission gearset. Without input speed vs output speed correlation, the TCM typically forces **2nd or 3rd gear limp-home mode** with harsh slams into Drive/Reverse; limit driving to short distances or have it inspected promptly to prevent clutch pack heat damage. Check **ATF fluid level and inspect for metal shavings** first, check the external **ISS harness/connector for ATF oil wicking or heat damage**, and test **2-wire VR sensor coil resistance (`~300–1,200 Ω`)** or **3-wire Hall-effect `5 V` / `12 V` supply and ground** ($35–$160 DIY for external sensor; $190–$680 shop for external/internal pan-mounted ISS).

- **URL:** https://faultcodes.org/automotive/obd2-p0715
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Transmission & Drivetrain
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Automatic transmissions calculate gear ratio slip and clutch apply timing by comparing **Input/Turbine Shaft Speed (`ISS`)** against **Output Shaft Speed (`OSS`)** and Engine RPM. Whether a 2-wire Variable Reluctance coil (`~300–1,200 Ω`) or 3-wire Hall sensor (`5 V`/`12 V`), thermal coil failure, ATF wicking into connector pins, metal clutch debris clinging to the magnetic tip, or broken wiring interrupts the signal and triggers `P0715`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Typical Limp-Mode Behavior | Locked in 2nd / 3rd gear + harsh shifts | TCM defaults to max line pressure & safe middle gear without ISS signal |
| 2-Wire VR / 3-Wire Hall Spec | ~300–1,200 Ω VR | 5 V / 12 V Hall | Test harness supply + ground before replacing external or internal ISS |
| Critical Physical Checks | ATF wicking & ferrous metal shavings | Metal fuzz shorts/distorts magnetic pickup; oil wicking ruins pin signals |

## Commonly Affected Models & Service Bulletins
- Chrysler / Dodge / Jeep 42RLE & 62TE / Hyundai / Kia (external 2-wire & 3-wire ISS)
- Ford F-150 / Mustang 6R80 & Mercedes-Benz 722.6/722.9 (internal lead-frame / conductor-plate ISS)
- Nissan Altima / Sentra CVT & Honda Accord / Civic automatics (input/primary pulley & turbine speed sensors)

## Common Symptoms
- Transmission locks in **2nd or 3rd limp gear** and refuses to upshift into overdrive
- Harsh bangs/slams shifting into Drive or Reverse, delayed gear engagement, or torque converter lockup disabled
- Live scan data reads `0 RPM` on **Input/Turbine Speed (`ISS`)** while moving, accompanied by `P0715` (and occasionally `P0717` / `P0730`)

## Most Likely Root Causes
- Failed **Input/Turbine Speed Sensor (`ISS`)**—thermally opening coil (`≠ ~300–1,200 Ω` VR) or failing internal Hall-effect IC
- **ATF oil wicking into the sensor connector**, corroded pins, or melted/rubbed harness near the transmission case & exhaust
- **Low/burnt ATF or ferrous metal shavings** sticking to the magnetic sensor tip (signaling internal drum/bearing wear)
- Damaged internal input clutch-drum reluctor teeth or failing internal **TCM / lead-frame conductor plate** (e.g., Mercedes 722.6 / Ford 6R80)

## Tools & Parts Reference
- OBD-II / TCM live-data scanner (**Input/Turbine RPM vs Engine RPM**)
- Digital multimeter (`300–1,200 Ω` VR resistance & `5 V`/`12 V` Hall probe)
- Drain pan, OEM-spec ATF, electrical contact cleaner & torque wrench

## Step-by-Step Troubleshooting & Fix
1. Top up low ATF with exact OEM-spec fluid and change dirty fluid/filter if metal debris coated the sensor's magnetic pickup tip.
2. Clean **oil-wicked connector terminals** with electronics cleaner and repair chafed transmission wiring or leaking O-rings/seals causing fluid wicking.
3. If supply/ground verify good (or 2-wire coil tests out of `~300–1,200 Ω` / opens hot), replace the external **Input/Turbine Speed Sensor** (or internal pan-mounted conductor-plate/lead-frame assembly where integrated) with OEM torque & O-ring.
4. Clear TCM/PCM codes, verify smooth live **ISS RPM tracking** matching engine speed in Park/Drive, and confirm normal upshifts across all gears.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $35–$160 | $190–$680 |
| GBP | £28–£130 | £150–£530 |
| CAD | CA$45–CA$210 | CA$250–CA$880 |
| EUR | €32–€145 | €175–€620 |
| CHF | CHF 40–CHF 175 | CHF 230–CHF 780 |

## Frequently Asked Questions
### Can I drive my car with code P0715 in limp mode?
Only briefly at low speeds to reach safety or a repair shop. Driving in **2nd/3rd limp gear** at highway RPMs overheats transmission fluid and accelerates clutch-pack wear.

### Is the Input Speed Sensor always external and easy to replace?
On many Nissan, Hyundai/Kia, Chrysler, and Honda transmissions it threads externally onto the case (`~20 min` DIY), whereas designs like Mercedes 722.6 or Ford 6R80 mount the sensors inside the pan on the **conductor plate / molded lead frame**, raising shop labor.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
