FaultCodes.org
P0113OBD-IIEngine Cooling & ThermostatVerified Guide· Updated: Nov 22, 2026

OBD-II P0113: Intake Air Temperature (IAT) Sensor 1 Circuit High

SAE J2012 fault when an open NTC circuit pulls the IAT line `> 4.6–4.85 V`, locking PCM air-temp readings at `< -40 °C (-40 °F)`—extremely common right after an air filter change leaves an integrated MAF/IAT plug unplugged.

Quick AnswerLow — Minor Issue

Code P0113 (SAE J2012) means the PCM detects Intake Air Temperature (IAT) Sensor 1 voltage stuck above `4.6–4.85 V`, causing live scan data to lock at `-40 °C (-40 °F)`—the classic sign of an open NTC thermistor circuit or lost sensor ground. On most modern cars the IAT thermistor lives inside the MAF sensor housing, so forgetting to reconnect the MAF plug after changing the engine air filter triggers P0113 (often with P0102) immediately. Check the MAF/IAT plug first, verify `5 V` reference and ground at the harness, and check NTC resistance across the sensor pins against ambient temperature ($0–$95 DIY; $95–$235 EUR / $110–$260 USD shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Engine Cooling & Thermostat
Professional Repair
$110 – $260

What This Fault Code Means

The IAT sensor uses a Negative Temperature Coefficient (NTC) thermistor whose resistance drops as intake air warms. The PCM supplies a regulated 5 V pull-up reference through an internal resistor and reads the voltage drop: warm intake air reads low voltage (~1.0–2.5 V), whereas an open wire, unplugged connector, broken ground, or failed open thermistor stops current flow and pulls the signal line up to `> 4.6–4.85 V` (`-40 °C / -40 °F`).

Common Symptoms

  • Live OBD-II scan data shows IAT locked at `-40 °C` (`-40 °F`) regardless of warm engine or summer weather
  • Check Engine Light (P0113) often illuminated immediately after an air filter or oil-change inspection
  • Slightly rich cold starts or minor fuel economy drop as the PCM substitutes default intake temp

Most Likely Root Causes

  • Unplugged or half-seated MAF/IAT connector forgotten after replacing the engine air filter (#1 cause—often $0 fix!)
  • Broken signal wire or open sensor ground in the 2-pin IAT or 5-pin MAF/IAT harness near the airbox
  • Failed internal NTC thermistor (open circuit inside standalone IAT sensor or combined MAF housing)
  • Corroded, pushed-back, or oil-contaminated connector pins preventing circuit completion

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
High-Input Voltage Threshold

Open NTC circuit pulls signal rail high, triggering P0113

> 4.6–4.85 V (against 5.0 V ref)
Default Locked Scan Value

Instant indicator of open sensor, unplugged MAF/IAT plug, or broken ground

< -40 °C (-40 °F)
Typical NTC Ambient Resistance

Resistance drops smoothly when warmed; OL confirms open internal thermistor

~2.0–3.5 kΩ at 20 °C (68 °F)

Commonly Affected Models & Service Bulletins

  • Toyota / Honda / Subaru / Nissan engines (IAT integrated inside 5-pin MAF housing)
  • Ford / GM / Chrysler trucks & sedans (airbox-mounted 2-wire IAT or integrated MAF/IAT)
  • Volkswagen / Audi / BMW / Mercedes-Benz models (combined intake air temp & MAF/MAP sensors)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read live OBD-II IAT temperature: a reading stuck at `-40 °C (-40 °F)` confirms an open circuit (> 4.6–4.85 V), then inspect the airbox/MAF plug immediately to ensure it wasn't left unplugged.
  2. 2Unplug the IAT (or integrated MAF/IAT) connector and test harness pins KOEO for a clean `5 V` reference and solid sensor ground (bridging the two IAT pins briefly with a jumper should drop the scanner reading from -40 °C to > +120 °C).
  3. 3Measure NTC thermistor resistance directly across the sensor pins and compare against ambient temperature (~2.0–3.5 kΩ at 20 °C / 68 °F for standard OEM curves; OL confirms a dead sensor).

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does the airbox / MAF connector show unplugged, loose, or have visibly snapped wires near the plug?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II scanner reading live IAT (°C / °F) & voltageDigital multimeter (checking 5 V reference, ground, and kΩ NTC curve)Fused jumper wire / backprobe pins & electrical contact cleaner
  1. 1Inspect the air intake duct and firmly click the MAF/IAT connector home if found unplugged after service.
  2. 2Clean corroded terminals and repair any cracked wire or pushed-out pin in the sensor pigtail (check ground continuity back to PCM/battery negative).
  3. 3If 5 V reference and ground test good (jumper test swings scanner from -40 °C to high temp) yet the sensor reads OL, replace the standalone IAT sensor (or integrated MAF/IAT assembly).
  4. 4Clear P0113 and confirm live IAT matches outside ambient temperature on a cold engine before starting.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0 – $95
Professional Repair (Parts + Labor)$110 – $260

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does my OBD-II scanner say -40 degrees for P0113?

An open NTC thermistor circuit lets the PCM's 5 V pull-up voltage rise past 4.6–4.85 V, which corresponds to the coldest bottom limit (-40 °C / -40 °F) on the sensor's lookup table.

Can I trigger P0113 just by changing my air filter?

Yes—very often! On vehicles where the IAT sensor is built into the MAF sensor on the airbox lid, unplugging the MAF to lift the lid and forgetting to plug it back in triggers P0113 on the very first drive.

Related Searches & Questions

OBD2 P0113 intake air temp -40 degreesP0113 after air filter change MAF sensorhow to test P0113 5V reference NTC resistanceP0113 IAT sensor 1 circuit high fix

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0113: Intake Air Temperature (IAT) Sensor 1 Circuit High | FaultCodes.org