# OBD-II P0113: OBD-II P0113: Intake Air Temperature (IAT) Sensor 1 Circuit High

> **Quick Answer:** Code **P0113** (SAE J2012) means the PCM detects **Intake Air Temperature (IAT) Sensor 1 voltage stuck above `4.6–4.85 V`**, causing live scan data to lock at **`-40 °C (-40 °F)`**—the classic sign of an **open NTC thermistor circuit or lost sensor ground**. On most modern cars the IAT thermistor lives **inside the MAF sensor housing**, so forgetting to reconnect the MAF plug after changing the engine air filter triggers `P0113` (often with `P0102`) immediately. Check the **MAF/IAT plug** first, verify **`5 V` reference and ground** at the harness, and check NTC resistance across the sensor pins against ambient temperature ($0–$95 DIY; $95–$235 EUR / $110–$260 USD shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0113
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Engine Cooling & Thermostat
- **Severity:** Low — Minor Issue
- **Safe to Operate?:** Yes (Short Term)
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
The IAT sensor uses a **Negative Temperature Coefficient (NTC)** thermistor whose resistance drops as intake air warms. The PCM supplies a regulated `5 V` pull-up reference through an internal resistor and reads the voltage drop: warm intake air reads low voltage (`~1.0–2.5 V`), whereas an **open wire, unplugged connector, broken ground, or failed open thermistor** stops current flow and pulls the signal line up to **`> 4.6–4.85 V` (`-40 °C / -40 °F`)**.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| High-Input Voltage Threshold | > 4.6–4.85 V (against 5.0 V ref) | Open NTC circuit pulls signal rail high, triggering P0113 |
| Default Locked Scan Value | < -40 °C (-40 °F) | Instant indicator of open sensor, unplugged MAF/IAT plug, or broken ground |
| Typical NTC Ambient Resistance | ~2.0–3.5 kΩ at 20 °C (68 °F) | Resistance drops smoothly when warmed; OL confirms open internal thermistor |

## Commonly Affected Models & Service Bulletins
- Toyota / Honda / Subaru / Nissan engines (IAT integrated inside 5-pin MAF housing)
- Ford / GM / Chrysler trucks & sedans (airbox-mounted 2-wire IAT or integrated MAF/IAT)
- Volkswagen / Audi / BMW / Mercedes-Benz models (combined intake air temp & MAF/MAP sensors)

## Common Symptoms
- Live OBD-II scan data shows IAT locked at **`-40 °C` (`-40 °F`)** regardless of warm engine or summer weather
- Check Engine Light (`P0113`) often illuminated immediately after an air filter or oil-change inspection
- Slightly rich cold starts or minor fuel economy drop as the PCM substitutes default intake temp

## Most Likely Root Causes
- **Unplugged or half-seated MAF/IAT connector** forgotten after replacing the engine air filter (#1 cause—often $0 fix!)
- Broken **signal wire or open sensor ground** in the 2-pin IAT or 5-pin MAF/IAT harness near the airbox
- Failed internal **NTC thermistor** (open circuit inside standalone IAT sensor or combined MAF housing)
- Corroded, pushed-back, or oil-contaminated connector pins preventing circuit completion

## Tools & Parts Reference
- OBD-II scanner reading live **IAT (°C / °F)** & voltage
- Digital multimeter (checking `5 V` reference, ground, and `kΩ` NTC curve)
- Fused jumper wire / backprobe pins & electrical contact cleaner

## Step-by-Step Troubleshooting & Fix
1. Inspect the air intake duct and firmly click the **MAF/IAT connector** home if found unplugged after service.
2. Clean corroded terminals and repair any cracked wire or pushed-out pin in the sensor pigtail (check ground continuity back to PCM/battery negative).
3. If `5 V` reference and ground test good (jumper test swings scanner from `-40 °C` to high temp) yet the sensor reads `OL`, replace the standalone **IAT sensor** (or integrated MAF/IAT assembly).
4. Clear `P0113` and confirm live IAT matches outside ambient temperature on a cold engine before starting.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$95 | $110–$260 |
| GBP | £0–£75 | £85–£205 |
| CAD | CA$0–CA$125 | CA$145–CA$340 |
| EUR | €0–€85 | €95–€235 |
| CHF | CHF 0–CHF 105 | CHF 130–CHF 295 |

## Frequently Asked Questions
### Why does my OBD-II scanner say -40 degrees for P0113?
An open NTC thermistor circuit lets the PCM's `5 V` pull-up voltage rise past `4.6–4.85 V`, which corresponds to the coldest bottom limit (`-40 °C / -40 °F`) on the sensor's lookup table.

### Can I trigger P0113 just by changing my air filter?
Yes—very often! On vehicles where the IAT sensor is built into the MAF sensor on the airbox lid, unplugging the MAF to lift the lid and forgetting to plug it back in triggers `P0113` on the very first drive.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
