FaultCodes.org
P0507OBD-IIPowertrain & Engine ManagementVerified Guide· Updated: Nov 22, 2026

OBD-II P0507: Idle Air Control (IAC) System RPM Higher Than Expected

Actual warm idle exceeds target map by `> 100–200 RPM` continuously (5–10 s) while throttle is closed—check unmetered intake vacuum leaks, carbon-bound Electronic Throttle Body (ETB) / IACV, and run the OEM Idle Air Volume Relearn after cleaning.

Quick AnswerModerate — Plan Repair

Code P0507 (SAE J2012) means the PCM tried to lower idle speed—commanding the Electronic Throttle Body (ETB) or Idle Air Control Valve (IACV) fully toward its closed stop—yet actual warm engine RPM stayed `> 100–200 RPM` above target for `5–10 seconds` continuously. Extra air is slipping past the closed throttle plate! Do not buy an IAC valve or throttle body first: inspect vacuum hoses, cracked intake manifold gaskets, leaking PCV valves, and brake booster lines (smoke-test or check high +LTFT fuel trims). Next, wipe carbon buildup off the throttle bore/plate and—crucially—perform the OEM Idle Air Volume / Throttle Relearn so the ECU stops holding the cleaned blade open ($10–$160 DIY; $120–$430 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Powertrain & Engine Management
Professional Repair
$120 – $430

What This Fault Code Means

At closed-throttle warm idle, the PCM targets a tight RPM curve (typically ~650–800 RPM). On drive-by-wire cars it adjusts the Electronic Throttle Body (ETB) opening angle; on older cable-throttle cars it modulates an IACV bypass motor. When vacuum leaks draw unmetered air—or after someone cleans carbon out of an ETB without resetting its learned open-angle offset—air volume exceeds the closed-throttle limit and trips P0507.

Common Symptoms

  • Warm idle hanging high (~1,000–1,800 RPM) or surging between gears with Check Engine Light (P0507)
  • Hard clunk when shifting an automatic transmission from Park/Neutral into Drive or Reverse
  • High idle appearing immediately after disconnecting the battery or cleaning a dirty throttle body

Most Likely Root Causes

  • Unmetered intake vacuum leak (split PCV hose, intake manifold gasket, brake booster check valve, or purge valve stuck open) (#1 cause)
  • Dirty/carbon-stuck Electronic Throttle Body (ETB) plate or binding Idle Air Control Valve (IACV) unable to close cleanly
  • Missing OEM Idle Air Volume Relearn after cleaning carbon off a throttle body (the ECU holds the clean blade too far open)
  • Worn throttle-shaft seal, misadjusted throttle cable stop screw, or faulty throttle body motor/TPS

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Idle Speed Deviation Threshold

Observed while closed-throttle idle air authority sits at minimum limit

> 100–200 RPM above target idle
Monitor Qualification Duration

Tested at hot operating temperature (~> 70–80 °C) in Park/Neutral

5–10 s continuous closed-throttle over-speed
Fuel Trim Leak Indicator

Separates unmetered vacuum leaks from clean-throttle relearn offsets

LTFT + STFT > +10% at idle
Post-Service Calibration

Required whenever ETB carbon is cleaned or battery/ECM resets

OEM Idle Air Volume / Throttle Relearn

Commonly Affected Models & Service Bulletins

  • Nissan Altima / Sentra / Rogue / Frontier & Infiniti Models (Idle Air Volume Relearn)
  • Chevrolet Silverado / Equinox / Malibu & Ford Focus / F-150 (ETB & PCV leaks)
  • Honda Accord / CR-V, Volkswagen / Audi TSI & Subaru Outback/Forester Models

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Monitor live OBD-II RPM, Target Idle RPM, Throttle Position (`TP%`), and Short/Long-Term Fuel Trims (`STFT/LTFT`) at hot idle in Park: high positive trims (+10% to +25%) paired with high RPM strongly indicate an unmetered vacuum leak.
  2. 2Inspect every vacuum line after the throttle plate—PCV valve/hose, brake booster hose, EVAP purge valve (pinch hose briefly with smooth-jaw pliers to see if RPM drops cleanly), and intake runner gaskets via an intake smoke test.
  3. 3Remove the intake duct to check the throttle bore/plate rim for sticky black carbon deposits or a sticking IACV pintle, and note whether P0507 began right after a battery swap or throttle cleaning.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Do live fuel trims show `+10%` or higher positive `LTFT/STFT` OR does pinching the PCV/purge/brake-booster hose drop idle RPM immediately?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II bi-directional scan tool (reading target vs actual RPM, LTFT & running Idle Air Relearn)Throttle Body Cleaner aerosol + lint-free microfiber clothIntake smoke tester (or smooth hose-pinching pliers to isolate vacuum lines)
  1. 1Repair all unmetered vacuum leaks first—replace split rubber vacuum hoses, leaking PCV valves, stuck-open purge solenoids, or hardened intake manifold gaskets.
  2. 2Clean black carbon buildup from the throttle plate edges and bore carefully using a lint-free cloth wetted with Throttle Body Cleaner (never flood shaft electronics or force-snap a drive-by-wire motor blade aggressively).
  3. 3If cleaning an older IACV, clean its carbon-coked pintle and housing passage (or replace a seized IAC stepper motor + gasket).
  4. 4Mandatory final step: Perform the OEM Idle Air Volume / Throttle Relearn (either via bi-directional scan tool or the OEM pedal/key sequence—classic on Nissan/Infiniti/Honda/GM) so the PCM learns the new clean airflow baseline and clears P0507.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$10 – $160
Professional Repair (Parts + Labor)$120 – $430

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does cleaning my throttle body sometimes CAUSE P0507?

Over miles, the PCM gradually opens the drive-by-wire throttle plate wider to breathe past thick carbon sludge. When you scrub that carbon away without resetting learned tables, that wider throttle angle suddenly lets too much air through, spiking idle RPM and setting P0507 until you run an Idle Air Volume Relearn.

Can I drive with code P0507?

Yes for short trips, though high idle causes harsh Drive/Reverse transmission clunks and requires stronger brake pressure at stops; repair vacuum leaks and relearn idle promptly.

Related Searches & Questions

OBD2 P0507 high idle RPM fix vacuum leakP0507 after cleaning throttle body idle air relearnNissan Chevy VW Honda P0507 IACV vs ETBP0507 idle RPM 100 to 200 higher than target

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0507: Idle Air Control (IAC) System RPM Higher Than Expected | FaultCodes.org