# OBD-II P0507: OBD-II P0507: Idle Air Control (IAC) System RPM Higher Than Expected

> **Quick Answer:** Code **P0507** (SAE J2012) means the PCM tried to lower idle speed—commanding the Electronic Throttle Body (`ETB`) or Idle Air Control Valve (`IACV`) fully toward its closed stop—yet actual warm engine RPM stayed **`> 100–200 RPM` above target** for **`5–10 seconds`** continuously. Extra air is slipping past the closed throttle plate! **Do not buy an IAC valve or throttle body first**: inspect **vacuum hoses, cracked intake manifold gaskets, leaking PCV valves, and brake booster lines** (smoke-test or check high `+LTFT` fuel trims). Next, wipe carbon buildup off the throttle bore/plate and—crucially—perform the **OEM Idle Air Volume / Throttle Relearn** so the ECU stops holding the cleaned blade open ($10–$160 DIY; $120–$430 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0507
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Powertrain & Engine Management
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** Yes (Short Term)
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
At closed-throttle warm idle, the PCM targets a tight RPM curve (typically `~650–800 RPM`). On drive-by-wire cars it adjusts the Electronic Throttle Body (`ETB`) opening angle; on older cable-throttle cars it modulates an `IACV` bypass motor. When vacuum leaks draw unmetered air—or after someone cleans carbon out of an `ETB` without resetting its learned open-angle offset—air volume exceeds the closed-throttle limit and trips `P0507`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Idle Speed Deviation Threshold | > 100–200 RPM above target idle | Observed while closed-throttle idle air authority sits at minimum limit |
| Monitor Qualification Duration | 5–10 s continuous closed-throttle over-speed | Tested at hot operating temperature (~> 70–80 °C) in Park/Neutral |
| Fuel Trim Leak Indicator | LTFT + STFT > +10% at idle | Separates unmetered vacuum leaks from clean-throttle relearn offsets |
| Post-Service Calibration | OEM Idle Air Volume / Throttle Relearn | Required whenever ETB carbon is cleaned or battery/ECM resets |

## Commonly Affected Models & Service Bulletins
- Nissan Altima / Sentra / Rogue / Frontier & Infiniti Models (Idle Air Volume Relearn)
- Chevrolet Silverado / Equinox / Malibu & Ford Focus / F-150 (ETB & PCV leaks)
- Honda Accord / CR-V, Volkswagen / Audi TSI & Subaru Outback/Forester Models

## Common Symptoms
- Warm idle hanging high (`~1,000–1,800 RPM`) or surging between gears with Check Engine Light (`P0507`)
- Hard clunk when shifting an automatic transmission from Park/Neutral into Drive or Reverse
- High idle appearing immediately after disconnecting the battery or cleaning a dirty throttle body

## Most Likely Root Causes
- **Unmetered intake vacuum leak** (split PCV hose, intake manifold gasket, brake booster check valve, or purge valve stuck open) (#1 cause)
- **Dirty/carbon-stuck Electronic Throttle Body (ETB)** plate or binding **Idle Air Control Valve (IACV)** unable to close cleanly
- **Missing OEM Idle Air Volume Relearn** after cleaning carbon off a throttle body (the ECU holds the clean blade too far open)
- Worn throttle-shaft seal, misadjusted throttle cable stop screw, or faulty throttle body motor/TPS

## Tools & Parts Reference
- OBD-II bi-directional scan tool (reading target vs actual RPM, `LTFT` & running **Idle Air Relearn**)
- **Throttle Body Cleaner** aerosol + lint-free microfiber cloth
- Intake smoke tester (or smooth hose-pinching pliers to isolate vacuum lines)

## Step-by-Step Troubleshooting & Fix
1. Repair **all unmetered vacuum leaks** first—replace split rubber vacuum hoses, leaking PCV valves, stuck-open purge solenoids, or hardened intake manifold gaskets.
2. Clean black carbon buildup from the **throttle plate edges and bore** carefully using a lint-free cloth wetted with **Throttle Body Cleaner** (never flood shaft electronics or force-snap a drive-by-wire motor blade aggressively).
3. If cleaning an older **IACV**, clean its carbon-coked pintle and housing passage (or replace a seized IAC stepper motor + gasket).
4. **Mandatory final step:** Perform the **OEM Idle Air Volume / Throttle Relearn** (either via bi-directional scan tool or the OEM pedal/key sequence—classic on Nissan/Infiniti/Honda/GM) so the PCM learns the new clean airflow baseline and clears `P0507`.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $10–$160 | $120–$430 |
| GBP | £8–£130 | £95–£340 |
| CAD | CA$14–CA$210 | CA$160–CA$570 |
| EUR | €10–€150 | €110–€390 |
| CHF | CHF 15–CHF 195 | CHF 160–CHF 530 |

## Frequently Asked Questions
### Why does cleaning my throttle body sometimes CAUSE P0507?
Over miles, the PCM gradually opens the drive-by-wire throttle plate wider to breathe past thick carbon sludge. When you scrub that carbon away without resetting learned tables, that wider throttle angle suddenly lets too much air through, spiking idle RPM and setting `P0507` until you run an **Idle Air Volume Relearn**.

### Can I drive with code P0507?
Yes for short trips, though high idle causes harsh Drive/Reverse transmission clunks and requires stronger brake pressure at stops; repair vacuum leaks and relearn idle promptly.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
