OBD-II P0304: Cylinder 4 Misfire Detected
Mode $06 Cylinder 4 misfire counter exceeded limit—swap Coil #4 -> #1/#2, inspect plug wear/carbon tracking, test injector resistance (`~11–16 Ω` port injection) + noid light, and check compression/leakdown if #4 stays dead; STOP if the CEL flashes.
Code P0304 (SAE J2012) means the PCM's Mode `$06` Cylinder 4 misfire counter detected recurring combustion misfires specifically on Cylinder 4. Safety first: if the Check Engine Light is FLASHING, pull over and shut off the engine immediately—raw fuel dumping out of Cylinder 4 can quickly overheat and ruin the catalytic converter. Isolate the failing part cleanly before spending money: swap Cylinder 4 ignition coil -> Cylinder #1 (or #2) and inspect the #4 spark plug for worn gaps or vertical black carbon tracking lines on the white ceramic insulator (move it to another cylinder like #3 to confirm). If the misfire stays locked on #4, check injector coil resistance (`~11–16 Ω` port injection) & noid-light pulse, then run compression & leakdown tests ($25–$180 DIY; $140–$580 shop).
- Safe to Operate?
- No — Risk of Damage
- DIY Difficulty
- Moderate (Intermediate)
- System
- Ignition & Misfire System
- Professional Repair
- $140 – $580
What This Fault Code Means
Using high-resolution Crankshaft Position Sensor (CKP) tooth timing, the PCM calculates rotational speed gains right after Cylinder 4 fires. Missing combustion on #4 causes a measurable deceleration dip that increments the Mode `$06` Cylinder 4 misfire counter, triggering P0304 and—under severe catalyst-heating misfires—a 2-Hz flashing CEL plus injector shutoff.
Common Symptoms
- Rough shuddering idle, heavy vibration under load, and reduced acceleration
- Steady or flashing Check Engine Light (`P0304`)—flashing signals immediate catalyst meltdown risk
- Raw gasoline smell from the exhaust and degraded fuel economy
Most Likely Root Causes
- Failing Cylinder 4 ignition coil, cracked rubber boot, or arc marks along the spark plug (carbon tracking) (#1 cause)
- Worn or fouled Cylinder 4 spark plug (excessive electrode gap) or oil leaking into plug tube #4
- Clogged, leaking, or electrically open Cylinder 4 fuel injector (
~11–16 ΩPFI coil out of spec) or broken driver wire - Low Cylinder 4 compression (burnt valve, blown head gasket—note #4 sits at the rear of many inline-4 engines where coolant/heat stress peaks—or worn rings)
Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold |
|---|---|
| OBD-II Misfire Counter Counts crankshaft speed dips tied to Cylinder #4 ignition timing | Mode $06 Cylinder 4 Misfire Counter |
| Port Injector Resistance (PFI) Combined with noid-light test to verify injector coil & PCM pulse | ~11–16 Ω at ambient temperature |
| Compression & Leakdown Rule Identifies burnt valve, head gasket, or ring wear when swap stays on #4 | ~120–180 psi (within 10–15%) / < 10% leakdown |
| Flashing MIL Safety Limit Prevents raw unburned fuel from melting catalytic converter brick | Immediate engine shutdown required |
Commonly Affected Models & Service Bulletins
- Subaru Outback / Forester / Impreza & Toyota Camry / Corolla / RAV4
- Volkswagen / Audi 2.0T TSI, BMW 4-Cylinder & Chevrolet Cruze / Equinox
- Ford Focus / Escape / F-150 & Honda Civic / Accord / CR-V Models
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Check whether the MIL is steady or flashing (never drive with a flashing MIL!), inspect the #4 coil and injector wiring, and verify live Mode `$06` Cylinder 4 misfire counts.
- 2Swap Coil #4 -> Cylinder #1 (or #2) and remove the #4 spark plug to inspect for worn electrodes or vertical black carbon tracking lines down the porcelain (swap the plug into a different cylinder such as #3—always pair a new boot if carbon-tracked); clear codes and observe if
P0301/P0302orP0303sets. - 3If misfire counts stay on Cylinder 4, unplug injector #4 to check `~11–16 Ω` coil resistance (port injection) + noid-light pulse during cranking/idle, and run a compression + cylinder leakdown test (
~120–180 psi, within10–15%).
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Does swapping Coil #4 -> Cylinder #1/#2 shift the misfire code to `P0301` or `P0302`?
Step-by-Step Troubleshooting & Fix
Tools & Parts Reference
14 mm / 16 mm) + torque wrench + multimeter (11–16 Ω injector check)Noid light injector tester + compression & cylinder leakdown tester- 1If black carbon-tracking lines appear on the #4 spark plug ceramic, replace both the spark plug AND the rubber coil boot/coil together—otherwise the scored boot immediately burns a carbon path onto the new plug.
- 2Replace any failed ignition coil or worn spark plug set proven by the swap test (plus valve cover tube seals if oil is present).
- 3If spark tests healthy yet
P0304persists on #4, test/replace a clogged or electrically open Cylinder 4 fuel injector or fix broken harness wiring back to the PCM. - 4If compression drops
> 10–15%below neighboring cylinders, run a cylinder leakdown test (listening at tailpipe, throttle body, and coolant reservoir) to pinpoint exhaust valve, head gasket, or piston ring repair.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $25 – $180 |
| Professional Repair (Parts + Labor) | $140 – $580 |
Recommended Diagnostic Tools & Replacement Parts
Check OEM specifications and compatible tools for this repair.
Frequently Asked Questions
What is carbon tracking on a spark plug and why does it cause P0304?
Carbon tracking looks like a thin black lightning streak running vertically down the white ceramic insulator. It happens when a cracked or loose coil boot lets spark voltage jump down the outside of the plug instead of across the gap—if you replace only the plug without the boot, the old boot immediately ruins the new plug.
Why should Cylinder 4 compression and leakdown be checked if swapping coils and plugs doesn't help?
On many 4-cylinder engines, Cylinder 4 sits farthest from the water pump or next to PCV/brake-booster vacuum ports. If spark and injector pulse test fine, a compression + leakdown test immediately rules out a burnt exhaust valve, intake gasket leak, or head gasket seep.