FaultCodes.org
P0440OBD-IIEVAP Emissions ControlVerified Guide· Updated: Nov 22, 2026

OBD-II P0440: Evaporative Emission (EVAP) Control System Malfunction

General EVAP self-test fail across purge, vent, or tank sealing—check gas cap O-ring first, then ohm-test purge (`18–30 Ω`) & vent (`20–40 Ω`) solenoids, verify FTP sensor baseline (`~2.5–3.0 V` KOEO cap off), and pinpoint leaks with a low-pressure EVAP smoke test.

Quick AnswerLow — Minor Issue

Code P0440 (SAE J2012) is a general Evaporative Emission (EVAP) system malfunction—meaning the sealed fuel-vapor loop failed its cold/warm self-test for tank pressure retention, purge vacuum draw, or vent closure. Before buying parts, inspect the gas cap rubber O-ring and filler neck lip (tighten until it clicks 3 times, or replace cracked gaskets), since a loose/worn cap triggers P0440 more than anything else. If the cap seals tightly, ohm-test the EVAP purge solenoid (`~18–30 Ω`) and canister vent solenoid (`~20–40 Ω`), verify the Fuel Tank Pressure (FTP) sensor reads atmospheric baseline (`~2.5–3.0 V` Key-On-Engine-Off with gas cap removed), and smoke-test the EVAP lines at low pressure (0.5–1.0 psi) ($15–$150 DIY; $110–$420 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$110 – $420

What This Fault Code Means

To capture raw gasoline vapors before they escape into the atmosphere, the fuel tank vents into a charcoal canister, which the PCM purges into the engine intake via the purge solenoid while closing the canister vent valve to pull slight test vacuum monitored by the Fuel Tank Pressure (FTP) sensor. Any vapor leak, stuck-open purge/vent valve, cracked hose, or skewed FTP pressure baseline sets P0440.

Common Symptoms

  • Illuminated Check Engine Light (P0440) with normal engine driving performance in most cases
  • Faint raw fuel vapor smell near the rear wheel well / gas filler door after refueling
  • Occasional hard restart right after topping off the gas tank if the purge valve is stuck open

Most Likely Root Causes

  • Loose, cross-threaded, or cracked rubber O-ring on the fuel filler cap (#1 most frequent cause)
  • Stuck-open/leaking EVAP purge solenoid (`18–30 Ω`) or dirt-jammed canister vent valve (`20–40 Ω`)
  • Dry-rotted rubber EVAP vapor hoses, rusted metal filler neck, or cracked charcoal canister housing
  • Skewed Fuel Tank Pressure (FTP) sensor (not returning to ~2.5–3.0 V atmospheric zero) or wiring corrosion

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Purge & Vent Solenoid Coils

Check electrical resistance plus mechanical air seal when unpowered/commanded

Purge 18–30 Ω / Vent 20–40 Ω (typical)
FTP Sensor Atmospheric Baseline

Confirms zero pressure reference before EVAP vacuum pull-down test

~2.5–3.0 V (KOEO with gas cap removed)
Safe EVAP Smoke Test Pressure

Higher shop air damages fuel tanks, canisters, and FTP sensors

0.5–1.0 psi (regulated nitrogen/smoke)
Monitor Fuel Level Window

EVAP self-test will not execute below ~15% or above ~85% fuel

15% to 85% tank fill required

Commonly Affected Models & Service Bulletins

  • Toyota Camry / Tacoma / Corolla / 4Runner (charcoal canister & VSV purge/vent valves)
  • Chevrolet Silverado / Equinox / Tahoe & GMC Sierra (canister vent solenoid & FTP)
  • Honda Accord / CR-V, Ford F-150 / Escape & Nissan Altima / Rogue EVAP Systems

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Inspect the fuel cap rubber O-ring for dry cracks or debris, clean the filler neck rim, confirm firm click-locking, and look under the hood and rear axle for split EVAP hoses or loose green service-port caps.
  2. 2Check live OBD-II FTP sensor voltage with Key-On Engine-Off (KOEO) and the gas cap removed (zero tank pressure): a healthy 5V FTP sensor reads atmospheric baseline around `~2.5–3.0 V` (varies slightly by OEM; flat 0 V or 5 V indicates a sensor/wiring fault).
  3. 3Disconnect and ohm-test the purge solenoid (`~18–30 Ω`) and vent solenoid (`~20–40 Ω`), verify mechanical sealing/blow-through when de-energized, and connect a low-pressure EVAP smoke tester (`0.5–1.0 psi`) while commanding the vent valve closed.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is the fuel cap loose, missing clicks, or cracked along its rubber O-ring / filler neck rim?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II bi-directional scanner (FTP voltage + commanding EVAP vent/purge valves)Digital multimeter (Ω solenoid check & 5 V FTP harness testing)Regulated low-pressure EVAP smoke machine (`~0.5–1.0 psi`)
  1. 1Replace a dry, cracked, or aftermarket non-sealing fuel cap with an OEM cap ($15–$35) and wipe corrosion off the metal filler neck sealing rim.
  2. 2If testing reveals a leaking/failed purge valve (allows air through while unplugged) or stuck vent solenoid (OL or jammed open with road dirt), replace the solenoid with an OEM part.
  3. 3Replace brittle rubber EVAP hoses, split plastic quick-connect fittings, or a cracked charcoal canister spotted during the smoke test.
  4. 4If FTP sensor voltage stays pegged off its atmospheric baseline with cap off, inspect its 3-wire 5 V reference/ground/signal harness or replace the FTP sensor, clear P0440, and complete the cold-soak EVAP monitor drive cycle.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$15 – $150
Professional Repair (Parts + Labor)$110 – $420

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Can I clear P0440 simply by tightening my gas cap?

Tightening a loose gas cap fixes the leak immediately, though the Check Engine Light usually stays on until the vehicle completes 1–2 cold-soak EVAP monitor checks (with fuel tank between 15%–85% full)—or you clear it with an OBD-II scanner.

Why must I never test EVAP lines with shop compressed air instead of a regulated EVAP smoke tester?

Full shop air (90–120 psi) can immediately rupture plastic fuel tanks, charcoal canisters, and the delicate 5 V Fuel Tank Pressure (FTP) sensor diaphragm. Always use regulated `0.5–1.0 psi` EVAP smoke pressure.

Related Searches & Questions

OBD2 P0440 EVAP system malfunction fixP0440 purge solenoid vs vent valve ohm testP0440 FTP sensor voltage KOEO gas cap offToyota Chevy Honda P0440 EVAP smoke test

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0440: Evaporative Emission (EVAP) Control System Malfunction | FaultCodes.org