FaultCodes.org
P0302OBD-IIIgnition & Misfire SystemVerified Guide· Updated: Nov 22, 2026

OBD-II P0302: Cylinder 2 Misfire Detected

Mode $06 Cylinder 2 misfire counter exceeded threshold—use fast coil-swap + plug-swap isolation (#2 -> #1/#3 to see if code moves to P0301/P0303), check spark gap, injector pulse & compression (`~120–180 psi`, within `10–15%`); STOP immediately if the CEL flashes (catalyst meltdown hazard).

Quick AnswerHigh — Service Soon

Code P0302 (SAE J2012) means the PCM detected crankshaft rotational deceleration on Cylinder 2's power stroke via its Mode `$06` Cylinder 2 misfire counter. Safety rule: if the Check Engine Light is FLASHING, pull over and shut off the engine immediately—raw unburned fuel pouring into the exhaust superheats and melts the catalytic converter within miles. Isolate the culprit in 10 minutes with a component swap test: move the Cylinder 2 ignition coil to Cylinder 1 or 3 (and if needed, move Cylinder 2 spark plug to a different cylinder). If the misfire jumps to `P0301` or `P0303`, replace the swapped part; if it stays on #2, check fuel injector pulse/resistance and compression (`~120–180 psi`, within `10–15%` of adjacent cylinders) ($25–$180 DIY; $140–$580 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$140 – $580

What This Fault Code Means

During every combustion event, the Crankshaft Position Sensor (CKP) tracks tiny rotational acceleration spikes. When Cylinder 2 fails to ignite or produces weak expansion, that brief deceleration increments the PCM's Mode `$06` Cylinder 2 misfire counter. Once misfire percentage threatens tailpipe emissions (steady CEL) or catalytic converter thermal safety (2-Hz flashing CEL), the PCM logs P0302 and often cuts fuel to Cylinder 2.

Common Symptoms

  • Rough, shaking idle, vibration under acceleration, and clear lack of power
  • Steady or flashing Check Engine Light (`P0302`)—flashing warns of active raw-fuel catalyst overheating
  • Strong raw gasoline smell from the exhaust pipe and sharp fuel economy drop

Most Likely Root Causes

  • Failing Cylinder 2 ignition coil (COP), cracked boot, or oil leaking into the #2 spark plug well (#1 most common)
  • Worn, carbon-fouled, or cracked-insulator Cylinder 2 spark plug with excessive gap
  • Clogged, leaking, or electrically open Cylinder 2 fuel injector or broken injector driver wire
  • Low Cylinder 2 compression (burnt exhaust valve, blown head gasket, worn piston rings, or broken valve spring)

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
OBD-II Diagnostic Monitor

CKP angular velocity deceleration tracked per firing event

Mode $06 Cylinder 2 Misfire Counter
Healthy Compression Benchmark

Values > 15% below adjacent cylinders point to valve/gasket/ring loss

~120–180 psi (within 10–15% variance)
Port Injector Coil Resistance

Verify injector pulse with noid light if coil & plug swaps stay on #2

~11–16 Ω (high-impedance PFI)
Flashing MIL Safety Threshold

Unburned Cylinder 2 fuel causes catalytic converter meltdown

Type A Catalyst-Damaging Misfire -> STOP

Commonly Affected Models & Service Bulletins

  • Ford F-150 / Escape / Focus & Dodge/Jeep/Ram Pentastar 3.6L & HEMI Engines
  • Toyota Camry / Corolla / RAV4 & Honda Accord / Civic / Odyssey Models
  • Volkswagen / Audi 2.0T TSI, BMW N20/N55/B58 & Chevrolet/GMC Engines

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Note whether the MIL is steady vs flashing (never drive under load with a flashing CEL!), inspect the Cylinder 2 coil connector/wiring for rodent damage, and check Mode $06 live misfire counts on your scan tool.
  2. 2Swap #2 ignition coil -> Cylinder #1 (or #3) while moving the #2 spark plug -> a DIFFERENT cylinder (e.g., #4) (on coil-on-plug engines), clear codes, and run the engine: if P0301 or P0303 sets, the coil failed; if P0304 sets, the spark plug failed.
  3. 3If the misfire stays on Cylinder 2 after swapping both coil and plug, test the #2 injector with a noid light + ohmmeter (~11–16 Ω port injection) and run a compression test (~120–180 psi, staying within `10–15%` across cylinders).

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

After swapping Coil #2 -> Cylinder #1/#3, does the misfire code jump to `P0301` or `P0303`?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II scan tool reading Mode $06 live misfire countersSpark plug socket (14 mm or 16 mm) with extension + torque wrench + feeler gaugeDigital multimeter / noid light + mechanical compression tester
  1. 1If engine oil coats the Cylinder 2 spark plug boot, replace the leaking valve cover / plug-tube gasket so fresh coils/plugs don't arc and short out.
  2. 2Replace the failed ignition coil or spark plug confirmed by the swap test (replace all spark plugs as a matched OEM iridium/platinum set if near service interval and gap carefully without prying the fine electrode).
  3. 3If P0302 stays on Cylinder 2 with verified spark, replace a clogged/dead Cylinder 2 fuel injector or repair broken PCM ignition/injector harness pins.
  4. 4If compression on Cylinder 2 drops > 15% below neighboring cylinders, perform a cylinder leakdown test to isolate a burnt valve, head gasket leak, or ring wear before mechanical engine repair.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$25 – $180
Professional Repair (Parts + Labor)$140 – $580

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Is it safe to keep driving when code P0302 causes a flashing Check Engine Light?

No. A flashing MIL signals a Type A catalyst-damaging misfire: unburned gasoline from Cylinder 2 ignites inside the red-hot catalytic converter, potentially destroying the converter ($800–$2,000+) or creating a fire hazard within minutes.

Why should I move the coil and spark plug to two DIFFERENT cylinders during the swap test?

Moving Coil #2 -> #1 and Plug #2 -> #3 tests both parts in one single restart: if the code shifts to P0301, it's the coil; if it shifts to P0303, it's the plug; if it remains P0302, you immediately narrow the fault to Cylinder 2 fuel, wiring, or compression.

Related Searches & Questions

OBD2 P0302 cylinder 2 misfire coil swap testP0302 flashing check engine light safe to driveP0302 spark plug coil injector or compressionMode 06 cylinder 2 misfire counter P0302

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0302: Cylinder 2 Misfire Detected — Causes, Fixes & Cost | FaultCodes.org